What if you forget the administrator password? How to bypass the Windows administrator password to enable blocked functions how to bypass the password on the Windows 7 laptop.

In the Boot menu, select the desired drive. When you start a computer in the download menu, select the launch from the Windows installation disk 7. When downloading from the BIOS menu, you need to go to the boot section using the keyboard, and then change the computer loading order in such a way that the installation disk with Windows 7 is indicated first in the list.

Load your computer from the Windows 7 installation disk and run the Windows installation program. You should save all changes before going out of the BIOS and then restart the computer. After these actions, you need to start the download from the installation disk. Press any key when the program is offered to start installing Windows.

Select a language and enter the required information. In the window that opens, you will be prompted to select a language and enter data. You can leave all these settings unchanged.

Click the Repair Computer button on the installation screen. Do not press "Set Now" (Install Now), otherwise installing Windows 7. You need to select the "Restore Computer" option in the upper left corner.

Select "Windows 7" from the list of operating systems. You need to make a choice of all operating systems installed on the computer. Most computers have only one operating system.

Select the menu "Run with command line support" in the next window. This action will start the command line.

Enter the following commands in order. The following four commands will help you access the command line from the password entry screen to enter Windows. This will allow you to reset passwords in the account after Windows download. Enter each of the listed commands in order by clicking ↵ Enter. After each action:

C: \\
CD Windows \\ System32
Ren Utilman.exe utilman.exe.bak
Copy Cmd.exe Utilman.exe.

Remove the installation disk from the drive and restart the computer. Now Windows 7 should be booting in normal mode.

Click. ⊞ Win + U at the entry stage in the Windows Account to open the command line. Such a combination of buttons, as a rule, allows you to call the "Special Opportunities" screen, but thanks to the previously entered commands, this will open the command line.

Enter. Net User. and press ↵ Enter. to display the list of usernames. All computer users will appear on the screen.

Sometimes to forget the Windows 7 password is very annoying, because you lose control over all data on your computer under this account. You can find solutions on the Internet and still do not know how to unlock the computer. And some incorrect actions can be harmful to your blocked computer.

So here we will show you how Course Windows 7 password In efficient ways 5, whether you want to get around the administrator password or do not want to log in.

Part 1. How to get around Windows 7 password using the command line

CMD, command line, is an advanced administration tool on Windows computers. This is a powerful feature that helps solve some system problems.

The solution to bypass the Windows password is pretty old-fashioned, but every time it works well. Here, to bypass Windows, you need to first log in to the Windows 7 computer as a guest, and then reset the Windows account password.

Log in to your computer with Windows 7 using a guest account. (Guest accounts do not require a password at all).

Copy and paste "cmd.exe" to the desktop. Rename "cmd.exe" in "SETHC.EXE".

Copy the file in C "\\ Windows \\ System32 and rewrite the file in this folder.

Restart the computer and press the SHIFT 5 key to enter the CMD. Enter "Net User MyuserName Mypassword".

Here "MyuserName" is the name of the user account, and "MyPassword" is a new password for the administrator account. Press "ENTER" to execute the command and restart the computer.

You can then use a new password to log in on Windows 7.

Part 2. How to bypass Windows 7 password by creating a new account

If you just forgot one of the passwords of the administrator on your computer with Windows 7, but you still have other available administrator accounts, you can log in to your computer and create a new administrator account to get around it.

Click Start, and then enter "CMD" in the search field. Right-click and select "Run from the administrator."

When the administrator's command row opens, copy and paste the following command to reset the lost user password.

net Username New_Password

"UserName" is a new account you create, and "new_password" - for your new account.

Thus, you can bypass the forgotten password Windows 7 and create another new account with a new password.

Part 3. How to bypass the administrator password using Windows Password Reset

If you forgot the administrator password and did not receive an administrator account, then you should use a password reset tool to help you bypass and create a new password for the administrator. You do not even need to log on to the Windows 7 computer.

Here we do not intend to use, but use only secure Windows Password Reset Software to do this.

Tipard who can help you cope with such a headache in simple steps. With the help of a brilliant program, you can easily remove the password of your local administrator accounts with CD / DVD and USB drive. In addition, you can also create a new administrator account in the Software Interface, without going into the control panel.

Follow the instructions and go around the Windows 7 Password to use it again.

Download and install the appropriate Windows Password Reset software on an affordable computer.

To circumvent a blocked computer password, you may need to prepare a CD / DVD or a USB disk as a bootable tool for writing Windows Password Reset to a Windows 7 locked computer. Thus, you can download and install the appropriate Windows Password Reset software on an affordable computer.

Create a boot CD / DVD or USB drive (as an example, consider the version of Windows Password Reset Ultimate).

When you successfully register the program you selected, you have two options to choose a CD / DVD or USB drive.

1. Insert the boot tool (CD / DVD or USB drive) to the computer by downloading this program. Then click "Write a CD / DVD" or "Write a USB".

2. Select "Write a CD / DVD" or "Write a USB" and click "Yes" to wait for the recording process (for example, take "Burn USB").

Install the download of the locked computer from the boot disk / USB drive

1. Insert the boot tool into the Windows 7 closed computer and restart the locked computer

2. Continue clicking F10 / DELETE / ESC / F8 / F12 when the screen lights up

This record data will have to log in to your BIOS interface of your locked computer, so you need to press the key to enter the BIOS interface.

Advice. The button required for clicking depends on your motherboard of your blocked computer, you may need to find out which key you should click.

3. After logging into the BIOS interface, select the "System Configuration" tabs and select "Download Options"\u003e Enter the "Download order"\u003e Change the "Download order" menu parameter and place the boot tool (CD / DVD or USB drive) first, At the bottom of the interface, you will find several key tips to help you save your settings. And then close the BIOS interface. After that, your blocked computer will reboot again. Then your computer will enter the Windows Preset Wednesday.

After logging in to the Windows Preset Wednesday, Windows Password will start automatically. Select Windows 7, where you want to bypass the administrator password.

If your Windows 7 has been created by several administrators, you can selectively select the user as you like by clicking on it.

Then click "Reset Password" and select "Yes." And click "Restart" to start a computer from Windows 7. After that you will find that the password of the selected account will be deleted from Windows 7.

1. If you want to get around the password only in Windows 7, you can do it at this step. If you want to add another administrator for your Windows 7, you need to perform more steps as shown below.

2. This software will also help you bypass the administrator password in Windows 10/8 / Vista / XP and much more.

Add an administrator account or other user account if you have a need. Click "Add user". You can add another account and set a password for a new account (only for Ultimate version). Click "Restart". And then you will get your boot tool.

The crawl process will be completed, and remove your boot tool, and the computer will reboot again. You will see several accounts (administrator account, previously blocked account or a new account, if it was set) in the log interface on Windows 7 computer. And you will be happy to find out what can enter your account without typing One password of your initial locked account.

More tools to restore a password for Windows, check it out here.

Part 4. How to bypass Windows Password With RESET DISK

If you have created in the past, below were the simplest steps that would help you bypass forgotten password in Windows 7.

When entering an incorrect password in the login interface in Windows 7, a message will appear, and you need to click "OK" to close the message.

Click "Reset Password", and then insert a disk to reset the password that you created earlier.

Follow the instructions on the screen to create a new password.

Then you just need to log in with a new password.

Note. The disc works only in the account you created if you changed Windows XP password for this account it is still working.

Part 5. How to skip password to enter Windows 7

If you can remember your password, but just want to skip the login window, you can easily remove the password by performing simple actions.

Click the Start button, and then click the image of your account to go to your accounts.

Click "Delete your password" and enter your current password and "Delete password" to confirm your work.

Then you can restart the computer to make sure that you do not stop on the login interface with the Windows 7 password.

The whole process is simple, right? You can try to independently bypass the administrator password on your Windows 7.

Output

Here we are mainly talking about ways to get around forgotten password in Windows 7. Regardless of your administrator password, or you do not want to log in, you can also find accurate solutions to fix it. Last Tip: You can remove Windows 7 password directly to avoid an additional stop when accessing a computer.

Of course, you could delete the set password.

Was your problem solved?

Let me know if you have any questions, leaving your comments.

How to reset the password in Windows If suddenly you forgotten it? I will tell about this today in this article. To change the password, we need a disk with a Windows distribution. I will disassemble an example on Windows 8. But this scheme allows you to change passwords on all modern operating systems including Windows 7.

Please do not consider this guide as an instruction on hacking Windows. This is the help of those who want to restore access to your computer account.

With this method, you can work with any account, including administrators. So that now you can easily get out of the situation even if you forget the password or you can help those who will be in this position.

By the way, if you do not know how to enable the administrator account, read here. Also, for clarity, I recorded a video. It is at the bottom of this article.

We load from the boot disk

So. Install the distribution of the operating system in the drive and load it from it.

In the next menu, press the SHIFT + F10 key combination. The command line opens.

We switched to an English layout using the "Alt + Shift" key combination and enter the "Regedit" command. Confirm the "ENTER" command and the registry editor opens.

Select a directory with an installed operating system. In my case it is a "local drive D". You choose your own.

We are looking for the file "utilman.exe". This is a special features program. It is loaded with system rights.

Press the right mouse button and select "Rename" in the context menu. You call it "Utilman1" (you can not be fundamentally any name).

Closes all windows and reboot the computer.

Reset user password

After rebooting. On the Greeting page, click the "Special Features" button

Start the command line

It needs to give a view command - "Net User Username Password". After the command via the gap, specify the username that you need to change the password and then also through the gap itself the password that we want to set.

That's all! The password from the forgotten user is changed and can be logged in. Now it remains only to rename back files. To do this, boot off the disk and do the reverse procedure.

Rename the "Utilman" file in "CMD" and "Utilman1" in just "utilman". So you install a new password from the computer for your account and can continue to work.

In conclusion, as promised, a video about that - how to reset a forgotten password in Windows:

Many users in order to secure their information from prying eyes, install the administrator password for your account in Windows. Some people for different reasons forget the installed protection code and to reset Windows password Conduct the procedure for reinstalling the entire system. And as you know, it takes about a long time.

There may also be problems with saving the necessary files, because we can not log in to the system, and when installing Windows, as we know, the local disk to which the operating system will be installed must be formatted. Well, of course you can always find a simpler solution to the problem, just this will be discussed in this article and you will learn how reset password in windows 7 Without resorting to reinstall.

The only complication is that we need an installation disk or flash drive, to work on the command line. If you do not have any other, you can always use your neighbor's computer to download the image and burn it to the disk or flash drive.

How to reset Windows 7 password if it is forgotten

Lased to reset the password protection in Windows 7 was the mode of sticking the keys, which is caused by a fivefold key by pressing the key Shift.Just like this will help to bypass our security code forgotten. The essence of the procedure is that when calling the plug mode, the command line window in which we will need to work will be opened. And how to make it read below.

To start, you need to boot from the installation disk or the drive flash drive. In the first window we click further.

In the next window, we are interested in the system recovery, click on it.

If you have multiple operating systems installed, all available, choose the desired and go on.

In the system restore parameters window, open the command line.

We enter the command:

• copy D: \\ Windows \\ System32 \\ SETHC.EXE D: \\and press ENTER.

sethc.exe. - file causing sticking mode with fivefold pressing key shift..

With this command, this file is copied to the disk root (D: \\) (the system is a disk (C: \\)).

• copy D: \\ Windows \\ System32 \\ Cmd.exe D: \\ Windows \\ System32 \\ SETHC.EXE

cmd.exe. - The file is responsible for calling the command line.

We replace this command in the sethc.exe file on cmd.exe. Confirm the change in key "Y".

In the password input window, call the command to the string five times pressing the key shift..

We enter the command: net User Andrey 54321 And confirm it by pressing ENTER.

• nET User - user selection function.
• Andrew is the name of the account (introduce your own).
• 54321 - New password.

After successfully passing the procedure, we enter the changed password and rejoice.

We replace the command line to stick the keys

If you are not interested in the sliding mode, you can leave everything as it is. To return to the call of this mode, read on.

As can be seen in the picture below, using the commands entered above, the file sethc.exe. moved to the root of the disk. And in the system folder system32, It was replaced by the command line. Now we should move it back. You can try simply transfer it to system32.and remove the false file located there. But perhaps it will not be possible to do this, due to the insufficient number of rights. Therefore, we use the string command.

Open the Start menu, enter search cMD I.run the found file on behalf of the administrator .

We enter the command:

• copy C: \\ SETHC.EXE C: \\ Windows \\ System32 \\ SETHC.EXE

Click Enter and confirm the key " y."If everything is done correctly with a fivefold keystroke shift.oh, the sticking mode opens .

ABOUTput your opinion about this article, well, of course, ask your questions if something suddenly went wrong.

Thanks for attention!

This guide will tell you how to do if you forget the Windows XP password and how to solve this problem without reinstalling the operating system. In addition, we will consider other possible problems with passwords. Windows 10 and Windows 7 operating systems have improved security features compared to earlier Windows XP / 2000 systems.

By the way, it is possible on your PC one of the frequently used passwords, a complete list of popular passwords, see.

In the extreme versions of Windows, a more efficient password system is used, designed to be used in business so that no one without the necessary authority can access information on your computer. This is a stick about two ends. Most users at least once forgets some important password. And then the user / owner of the information becomes the enemy without access "for his computer.

Naturally, for each way of protection there is a way to get around it, especially if you have physical access to the computer.

In this article, we will look at various methods of protecting the computer using the password and how to get around them. We begin not with passwords of user accounts, but with no less important passwords, such as BIOS passwords.

How to "get around" Password BIOS?

Password BIOS. - One of the oldest ways to protect the computer from unauthorized access and one of the most common. Why? This is one of the most effective means if the user does not have access to the system unit. Otherwise, it is like locking the house into a variety of locks and leave the window open.

The default BIOS settings in all system boards do not store password information. So everything you need to do to remove the BIOS password - just reset the current settings by restoring the default configuration. But remember that the reset of the current BIOS settings will destroy not only the password, but all the same settings that you installed yourself.

There are two ways to reset the BIOS settings. Most system boards have a special jumper to clean CMOS (the memory in which the BIOS settings are stored). Usually this jumper is located near the battery on the motherboard, but it is advisable for complete confidence to refer to the instructions from the motherboard. On some motherboards, instead of jumper, there are simply two contacts that you need to close the metal object to reset the CMOS, such as a screwdriver.

If you have a jumper on your board, turn off the computer to clean the CMOS, install the jumper so that it closes the contacts of the jumper, and press the computer's power button. Your computer will not start loading, but the installations in CMOS will be reset. Remove the jumper and turn on the computer again. Most likely, you will see the request on the screen to press F1 to install the BIOS parameters. If you are satisfied with the default settings, press F1, and in the BIOS menu, select the 'Save and Exit' (Save and Exit). After that, the computer will boot as usual, with the exception of the BIOS password.

If you do not know where your board is the necessary jumper or there is no, which is quite possible, you will have to go to another. On each motherboard there is a battery that is a power source for CMOS memory, allowing you to save information. As a rule, this is a standard CR2032 battery.

To clean CMOS, turn off the computer and remove the battery (you may need a thin screwdriver). After 5-10 minutes, install the battery in place and turn on the computer. The default parameters will be installed in the BIOS, and the password will not be. To continue the download, you will need to press the F1 key, and if you set up the default settings, select the 'Save and Exit' menu that appears in the BIOS menu.

As you were convinced, all this is very simple on the desktop, but with a laptop, the BIOS password can become a serious problem. Due to the frequent theft of laptops, the manufacturers take care of accessing, bypassing the password, it was almost impossible. So, if you forgot the BIOS password from your laptop, most likely you will have to contact the manufacturer's service center.

What if you forgot the password from Windows?

If the circumstances have developed in such a way that you have forgotten the Windows password, then, we recommend that you reset it is guided by the built-in account called the administrator. This is done in safe mode, during boot or reboot your PC.

To restore access to your computer, you will need to simply press F8 and in the menu already opened in which some additional options for downloading your operating system will be presented to your attention, you will have to choose the aforementioned "secure mode". Next, you need to select an embedded account, which, by the way, by default, cannot be protected by any password.

If you are all done correctly, since the above-mentioned sequence of actions accurately complied with the above, then you should knock out a window with a message that Windows works in the required, "safe mode" that is as simplified as possible. You will need to click "Yes" and go to the control panel - user accounts where the account icon is the password from which you are your own and want to lose. On the left you must select the "Change Password" item and enter the appropriate window, and after and confirm the new password. Ultimately, that the above-mentioned changes have entered into their legal force, you will need to restart the PC.

How to hack Windows password on a computer or laptop?

In order to do this, you will have to adhere to the following sequence of actions:

1. Prepare a CD, or the same flash drive to which a special set of resuscitation programs that intend to restore Windows will be recorded. You will need to insert it into the drive or in the appropriate port during the subsequent reboot of the computer. This resuscitation software package can be prepared independently by downloading a program there intended to separate, save and recover data, or even download some, are ready, RBCD 10.0, for example;
2. During the PC start, in order to go to the BIOS, press the "Delete" button. There we will need to change the priority of the installation and assign the computer download from the CD-ROM. After that, we visit our boot disk into the drive and reboot PCs;
3. Going into my resuscator disk, which should appear with us after the resuscitation package is loaded, we must select the editable copy of Windows and go to "System Recovery" mode - a section that will be in you at the bottom of the page;
4. We are looking for a command line and enter the "regedit" there (we look for it in the dialogs of the same window). We find, and after and allocate the HKEY_LOCAL_MACHINE section, in which we need to choose File, and then Load Hive;
5. Open the file "SAM" and select the section - HKEY_LOCAL_MACHINE \\_name \\ Sam \\ Domains \\ Account \\ Users \\ 000001F4. Twice click on the key placed there and go to the very first value located in the string that we need to replace the number 10;
6. In the same section, select "File", and then "Load Hive". Click "Yes" to confirm the unloading of the bush. We close the registry editor, thus end the installation process, take the flash drive or disk and reboot the computer.

How to find out the password from the computer?

Question: How to hack the password on the computer, remains relevant until now. Unfortunately, it is really possible to find out the password from the computer, it is possible only correctly in hand in hand. Therefore, if you are not ready to spend a few hours of your free time on this process, we strongly recommend that you just reset it and come up with some kind of new one.

Again, it is much easier to just reset the password and come up with some new one. However, if you need to find out the password, we recommend that you use the program for this purpose what is called, from the image of which you will need to make a boot disk. By setting up the BIOS booting from the drive and installing this program, immediately at the input to the desktop, you will open the window in which you can see usernames, including administrator, as well as passwords from their accounts.

Worth the question: what to do if I forgot the password from my own PC, it is absolutely not necessary to use the above methods of its recovery. Password reset in the Windows 7 operating system, can also be made using the Net User command. For this case, during the restart of PC you need to press F8. Thus, you can open the menu allows you to make additional options for downloading this operating system in which you will need to choose not just "safe mode", and such that would also support a command line. While in it, you will need to choose the built-in administrator account and in the command interpreter window, immediately, after that, the system invitations appear where you need to enter the Net User Name "Password".

We assume that you yourself understand that instead of the "username" you need to enter the name of your local user account, and instead of the "password" you have a new password. If you are all done correctly, in order to close the window, you will need to register on the command line: EXIT and restart the PC.

How to reset the password on windows 8?

In the case of this operating system, things are much simpler! Password reset on Windows 8, can be implemented as follows:

• You will need to click on the login screen to click on the special power icon, which is in the lower right corner of your screen;
• Next you will need to press the SHIFT key and click "Reboot";
• Click "Troubleshooting";
• Click "PC Reset";
• Click "Next" and the system will automatically restart in order to start preparing for the password reset.

How to reset the password on windows 10?

It's not so difficult to reset the password to users of Windows 10, of course, provided if they have access to email, or the same to the phone to which their account was tied. Otherwise, you will have to drop the password from the flash drive, as it has already been described above.

How to reset the Windows 7 administrator password?

Upload the Windows 7 administrator password is best through the Windows command interpreter. Observe the following sequence of actions:

1. First, run it. You can do this while holding the following path: Start - Run - Start the program - CMD. In the command interpreter opened menu, you will need to enter: Control UserPasswords, after which you will open the window called "User Accounts";
2. Highlight the password account from which you want to reset and do not forget to remove the checkbox of the "Require user name and password" checkbox;
3. In the window that opens, you will need to enter, and after and confirm the new password. Next, in the command boot window, you need to enter Exit and restart the PC, as usual.

View passwords that store windows

In addition to the passwords of access of various users, Windows stores and a number of other, no less important: password connecting to the Internet, passwords of mailboxes or access to Web sites. They are usually quite a lot, so it is quite natural that they are forgotten with time.

The operating system offers the "Auto-Fill" function for passwords and other frequently entered information in browsers (Google Chrome, Yandex.Browser, Opera (Blink), Firefox, Explorer 11 and D.R.). So not a rare situation when the user enters the password once, and in a few months, naturally, can not remember it. Everyone understands that important passwords need to be recorded, but they do not all. And if you no longer remember the password, how to find out, because it is displayed in the form of a row of stars: ******?

The solution is offered programs from different manufacturers that can get a password from this row of stars. There are quite a lot of freely distributed programs to decode Windows passwords or hidden passwords from input rows in various browsers.

We will use the program from Passware. This is a convenient in handling a freely distributed program that analyzes the passwords hidden as stars and informs them to you. It is very easy to work with her. It is enough to highlight the string with the password and click the 'Recover' button.

Of course, there are also commercial versions of programs that, as a rule, have a large set of functions. For example, the Password Recovery Toolbox program scans the system and defines saved passwords, data stored for automatic fill, Outlook Express passwords, passwords for connecting to the Internet, etc. This information is then presented in a convenient form. A few more alternatives above the programs described:, or Password Viewer.

Windows XP users passwords

Windows XP stores user passwords in the changed form. For example, Password password will be stored as a string similar to this: 'HT5E-23AE-8F98-NAQ9-83D4-9R89-MU4K'. This information is stored in the file called SAM in the C: \\ Windows \\ System32 \\ Config folder.

This part of the SAM file is encrypted by the SYSKEY system utility to improve password security. The data required to decrypt information after SYSKEY is stored in the System file in the same folder. But this folder is not available to anyone from users. Access to it has only the operating system itself during its work. You can access the SAM and System files only running another operating system or connecting the disk to another computer with the Windows system.

All versions of Windows XP have an ADMINISTRATOR account. This name gives the user full access to the system and the ability to reset passwords of all other users. It can save you if you for any reason can not go under your usual password of the user. The specific use of the administrator password depends on the Windows XP version: XP Professional.

The administrator password is set during the installation of the operating system. If you recorded it or simply pressed Enter, leaving it empty, then you will easily enter the system as an administrator and reset user passwords. To enter the system in the administrator mode, on the screen with a greeting system, press twice Ctrl + Alt + Del, a window will appear to enter the administrator password.

When the computer boots, go to 'START \\ CONTROL PANEL \\ User Accounts' (Start \\ Control Panel \\ User Accounts) and change the required password. Since you are here, it is a good opportunity to correct your error if you left the administrator password empty. In addition, it is desirable to change the name of the 'Adminisrator' account. This name is known to everyone and use it first to access your computer. To change the account name, right-click on the 'My Computer' and select 'MANAGE'. Open 'Local Users and Groups' and open the 'Users' folder. Right-click on the 'Administrator' entry and change it.
XP HOME.

This system will not let you just get access to the computer in the administrator mode. First you will need to download the computer in the protection mode from failures. To do this: restart the computer; Immediately after testing BIOS, press F8 several times; In the menu that appears, select 'START Windows XP In Safe Mode' (download Windows XP in failure protection mode). When the computer boots, go to the name of the 'Administrator'. The default password is missing. Now you can change user passwords by going to 'START \\ CONTROL PANEL \\ User Accounts' (Start \\ Control Panel \\ User Accounts). When you finish, restart the computer in the usual way.
Creating a disk dropping passwords

Windows XP allows you to record information on the usual diskette that provides the ability to reset the password. Naturally, if you have already forgotten the password and cannot access the system, you cannot create any disk, but you will start such a floppy disk in advance to protect yourself from such randomness.

To create a floppy disk: Go to 'START \\ CONTROL PANEL \\ User Accounts' (Start \\ Control Panel \\ User Accounts); Select the name under which you entered the system; In the related task menu, select 'Prevent A Forgotten Password' (prevent password forget); Follow the instructions that running the wizard.

To drop passwords using a floppy disk: If you enter a password when entering the system is incorrect, the system will ask, or you have not forgotten; At this stage, you can use your floppy disk, following step-by-step instructions of the operating system.

Be careful: If you used the built-in Windows capabilities to encrypt files and folders, but did not install the operating system update (Service Pack 1), the password deletes will result in loss of encrypted information.

Windows XP / 7/8 / 10 password change utilities

There are special utilities that allow you to edit or reset the passwords of Windows XP / 7/8/10 users. The principle of operation of most of them is to download the minimum version of an alternative operating system, such as DOS or Linux, which can be accessed by access to files with passwords.

An example of such a utility can be found at this address: http://home.eunet.no/~pnordahl/ntpasswd/ work instructions, as well as files to create Linux boot disk, are available on the same site.

Please note that if you used the functions of the operating system to encrypt files and folders by changing the password using any program, you will lose access to encrypted data. In this case, the following method can help, allowing not to replace the forgotten password new, and know the old one.

Password selection and decoding

If nothing else helps, but you have physical access to the computer, it means not all is lost. You can rewrite Config and SAM files and try to decipher passwords that are stored in them using special third-party utilities. As we have said, this will have to use an alternative operating system, such as DOS or Linux. And when files are at your disposal, you can use one of the password decryption programs, for example, LC4 or.

You will need:

1. Access to another computer.
2. At least two empty floppy disks.
3. An archiver designed to work with the command line, for example, RAR.
4. The DOS or Windows 98 boot disk (the image of the required disk can be obtained at http://www.bootdisk.com/) or the minimum version of Linux (for example, Knoppix). The need for boot disks disappears if you can simply connect your hard drive to another computer. If you use the DOS boot disk, and the partitions on your hard disk use the NTFS file system, you will need a program to access them that allows you to view sections in NTFS format, such as NTFSDOS.
5. The program for receiving passwords. We recommend using, since the Bat version of this program is free, and the free version of the LC4 is very limited.

Using the loading flash drive:

1. If there are sections in NTFS format on your hard disk, copy the NTFSDOS file to your boot flash drive.
2. Copy the archiver (RAR) on the boot flash drive.
3. Load a computer from this flash drive. If there are sections with NTFS, type the NTFSDOS command, this program will show which letter is assigned to your system disk, and it will be necessary to use it instead of the letter C in the next item.
4. Place the system files with passwords in the archive. For example, if you are using the RAR32 archiver, the corresponding command will look like this: RAR32 A -VA: \\ Systemandsam C: \\ Windows \\ System32 \\ Config \\ System C: \\ Windows \\ System32 \\ Config \\ SAM If the files do not fit on one USB flash drive, archiver Asked you to insert the second.

Hacking passwords

Each of your selected programs will display a list of accounts detected in the SAM file. Choose those of them, passwords to which you need to determine. If you are using, select ATACK TYPE: BRUTE-FORCE. If you used only the numbers in the password, check the 'All Digits (0-9)' item. Start the password selection process using the command from the Recovery menu.

The selection of the password can last from 10 minutes to several hours, or even a few days, and it may end up. Especially if letters in various registers, numbers and special characters are used in the password.

This is a good way to verify the reliability of your passwords. If you want to just check your password, do the steps described above and see how long it will take its selection.

Programs for hacking password in Windows

Software that can help you crack a password in Windows There is a huge amount. In addition to the above-mentioned program, there is also Windows Admin Password Hack. But, unfortunately, it is impossible to call it now because it works only in Windows 2000 / XP. Its closest replacement is MULTIBOOT 2K10, which is essentially a functional boot disk.

conclusions

In any case, if someone from your loved ones forgot your password on Windows 7, well, or you yourself have been forced to come across this - do not despair, there are a lot of solving this problem. Well, in order to: how to hack a password on a laptop - you no longer arose, we strongly recommend that you save them anywhere, in notes inside your own smartphone, for example.

We hope that you do not have to resort to the methods described by us. So that such a need has not arise, remember that all important passwords need to record. And if there is a real need to protect information on your computer, use passwords from characters in both registers and numbers and do not use ordinary words. In this case, your passwords will be very difficult to hack.

3 more useful articles:

A program that checks the reliability of user user passwords. This utility uses network administrators to calculate users with ...

A simple utility that allows you to display passwords hidden stars. Compatible with all browsers, among them and ...

Windows Repair is a rare type of program that can save your personal computer almost from all ...