Backlash of the volume and power buttons on the iPhone - marriage or not? iPhone mute switch not working iPhone mute button not working.

If the volume button on the iPhone does not work for you (for example, it sticks), do not rush to give the phone to a service center. Before you find out the cost of repairs and pay for the replacement of buttons (switching to silent mode or volume control), clarify the cause of the malfunction and try to fix it yourself.

Main causes of malfunctions

Primary diagnostics of the device can be done at home. If the volume button on the iPhone does not work - you do not hear a characteristic click, you feel that the mechanism is loosened - most likely, the cause is mechanical damage. Shocks and drops easily damage cables, screen, system board and other buttons (volume, lock, turn iPhone on and off, switch to silent mode). Often, the smartphone not only does not go into silent mode, but generally stops turning on after a strong mechanical impact.

Often problems with the iPhone occur due to liquid flooding. The penetration of moisture into the housing leads to serious consequences. It is important to dry the phone in time, clean the contacts and tracks, prevent corrosion, otherwise the problems may be not only with the sound.

Buttons "Volume" (decrease and increase the volume), "Power" (on and off) and "Mute" (mute, switch to silent mode) do not always break. In some cases, they stop working due to software glitches. For example, when you install unlicensed software on your iPhone or the firmware does not work correctly.

Symptoms of malfunctions:

the button is broken, does not respond
volume control (decrease, increase) does not work
button sticks, works irregularly

If you are sure that the buttons do not work due to a factory defect, immediately contact your Apple reseller, an authorized service center. In another situation, try fixing the problem with the iPhone yourself.

Troubleshoot software and adjust settings

In the process of diagnosing the device, you should pay attention to the iPhone settings - the phone may be working in silent mode. There is also a chance that a recently installed application is causing the blockage. Then it's worth doing a hard reboot:

simultaneously press "Power" and "Home" (for the iPhone 7, the on and off and volume buttons work this way, if the latter is not broken)
hold them until the phone turns off and the Apple logo appears

As a last resort, go through the iOS restore procedure through iTunes.

Where to go for repairs

Immediately contact the specialists if the software is working properly, and the mechanism for adjusting or turning on the silent mode has stopped working due to mechanical damage or flooding. When the warranty periods are violated, it is not necessary to waste time on a trip to the service center - it is much more convenient to call the master at home.

iPhones have great speakers, of course, but there are times when you might want to turn on what's called "Silent Mode," that is, turn off the sound. This function has long been possessed by almost all mobile (portable) communication devices, from ordinary cell phones to PDAs. And, of course, Apple products are no exception, here this mode is especially well debugged. As a rule, it is used in a working environment, at universities and institutes at lectures, at performances in theaters and in other situations where the rules of etiquette require silence. Don't worry about missing an important call. After all, the delicate vibration of the iPhone will certainly notify you of an incoming call, an update, a letter, and an SMS.

In order to activate silent mode on a device like the iPhone, you do not have to make a lot of unnecessary gestures, going through a bunch of settings over and over again. Everything can be done in just a second. On each iPhone model that currently exists, there is a convenient switch on the left side of the case near the display (top). One movement - and the phone will stop making any sounds, reminding of itself only by vibration at the right moments. iPhone vibrating alert is not loud.

Now we will talk about the positions that such a switch can take and how to quickly understand which mode is currently on. And so, in one position the lever creates a silent mode, and in the other - normal. In the first case, a small red dot or stripe is lit on the switch itself (depending on the phone signal). In addition, notifications are displayed directly on the iPhone display when switching between the two described modes. If you turn on the sounds, then the bell image appears, if you turn it off, the bell still appears, but already crossed out with a thick enough line obliquely.

Note that in silent mode, in any case, the alarm clock works, as well as sound notifications from the calendar: iPhone developers do not want to let their customers oversleep something or miss an important meeting, event, event. In addition, you yourself can even listen to the track with the sound turned off, view the video recording, and so on. But in applications, music and sound in general will not work until you remove your gadget from silent mode.

By the way, even in normal mode, you can easily reduce the ringer volume when incoming. Firstly, you can achieve this simply by opening the volume control menu, and then moving the pointer to the lower - zero - position. Secondly, you can use a special volume debugging button or a trite multifunctional Power button, one short press of which immediately extinguishes the call melody, while it does not reset itself - you can still pick up the phone. But the second press of the same will interrupt the call completely.

As you know, any picture taken with the camera in the iPhone is accompanied by a sound that simulates the shutter of the camera. This click sound is just a prop and you might think there should be an easy way to turn it off. I hasten to disappoint you, but such a setting does not exist in the iPhone.

If you constantly use your smartphone as a camera, then the presence of such sound is not always convenient. In some cases, "clicking the shutter" with each shot will simply be inappropriate.

In this article, we will show you how to turn off the camera sound on your iPhone and take photos without causing inconvenience to others.

On Apple iOS devices, you can use some tricks to solve this problem. Below are a few ways to turn off/on the camera shutter sound on iPhone.

These tips are universal and suitable for all models, so you can use them for any smartphone and tablet from Apple, regardless of the version of iOS that is installed on it.

Put your phone on silent mode

The easiest way to turn off the camera shutter sound on your iPhone is to use the silent mode switch located in the upper left corner. When you activate it, you will feel the vibration of the phone, and an orange stripe will appear on the button. Keep in mind that in silent mode, the sounds of notifications, incoming calls and other functions are also disabled.

If you cannot find the switch, then your model may not have such a function or it is under the cover. In this case, remove the protective case/cover from the phone. Oddly enough, this is the most primitive way to turn off the camera shutter sound on iPhone and iPad.

Turn down the volume

What will you do if the mute button doesn't work? In this case, the most obvious solution seems to be reducing the sound level, but if you try to do this in the Camera app, then turn on the time-lapse mode.

If you intend to take a picture, turn down your phone's volume before opening the app. This can be done by pressing the corresponding button on the left side of the phone. It is located under the mute switch.

If you have already launched the Camera app, you can reduce the sound level as follows. Swipe up from the bottom of the screen to open the Control Center, then swipe left to open the volume control. With it, you can turn off the sound of the camera on the iPhone.

Mute shutter effect sound with music app

Another method has been discovered on how to turn off the camera shutter sound on the iPhone, which works with iOS 7, iOS 8, iOS 9 and newer, regardless of the "Mute" switch. This is a workaround that involves playing the song, here's how it works:

1. Open the Music app and play a song, no matter what.

2. Now, use the volume buttons on the side of the iPhone and turn the volume of the song all the way down to zero.

3. After that, use the "Camera" application in the normal mode - after this, when shooting, the camera will not make a sound.

There are also other ways to turn off the camera sound on iPhone and iPad. They are a bit more difficult, but still worth mentioning.

Use Using Assistive Touch

Turn on the Assistive Touch function and adjust the audio level control. To do this, go to "App Settings" → "General" → "Access" → "Assistive Touch" ("Settings App" → "General" → "Accessibility" → "Assistive Touch").

For convenience, add a mute control button to the Customize Top Level menu. Now you can turn off the shutter sound before turning on the camera or while using it by simply tapping the picture on your iPhone or iPad (iOS).

There are also alternative ways to remove the sound of the iPhone camera:

● The first way is quite funny if it didn't cause tears. Its essence is to take a photo while recording a video. You won't hear the shutter sound, but you'll get a lower quality image (same resolution as the recorded video) and an unwanted video file that will have to be deleted in the future.

● The second method will not remove the sound when shooting, however, it will not be heard by others. All we need is to connect headphones (it doesn't matter standard wired or bluetooth) and take pictures.

I do not think that wearing headphones will be a problem, since a large number of people cannot go about their business without music or an audiobook. However, if you are in the company of friends, plugging your ears can be bad form.

● The third option is the most harmless and effective. After all, it will remove not only the sound of a click when shooting a camera on an iPhone, but also turn off all sound in principle. Just turn off the sound of the audio player.

Alas, all these methods do not turn off the sound of the camera, without incurring consequences for other systems. The only way to turn off the camera sound on iPhone and iPad is to download a jailbreak.

How to remove camera sound on iPhone and iPad with jailbreak?

Removing the camera sound on a jailbroken iPhone/iPad is much easier as there are a huge number of apps that help you do it. A great example is the "StealThsnap" app, which turns off the camera shutter sound on the iPhone. You can download it to your iPhone, iPad or iPod.

Who needs the StealThsnap app?

The Stealthsnap Cydia app allows you to turn off the camera shutter sound on your iPhone. Its developer Lex is a talented rookie in the field of cracking software development. The application is very convenient to use for all models of smartphones and tablets.

How safe is the application?

The application is completely safe as it simply changes the name of the photoShutter.caf file. This file in iOS memory is responsible for the sound of the camera shutter. After renaming the file, iOS stops seeing it and the sound of the camera trigger disappears.

When the application is deleted, the file returns to its original state and the shutter sound reappears.

How to download the application?

If you live in a country where the sound of taking photos should always be turned on, then this application is a must for you. You can download Stealthsnap.

What else makes the app stand out is its amazing compatibility. It supports all versions of operating systems from iOS 1 to iOS 10.2. In the future, it will also be compatible with iOS 11 without installing any additional modifications.

If the iPhone was purchased recently, then this article will be very relevant for you. The volume settings and switch on this phone are quite different from the standard settings on any other smartphone.

The first thing you need to pay attention to when using an iPhone is the mode switch located on the side panel above the volume buttons. This mechanism will allow you to put the phone on the silent profile without taking it out of your pocket, or vice versa, remove it from the silent profile and turn on the “Normal” profile. Such a toggle switch is available in all smartphone models and is very convenient to use. If you see a red bar, your phone is in silent mode, and if you don’t see it, then it’s in normal mode.

Also check if your iPhone 5s or 6 is connected to a headset, because when connected, the sound will only come from the headphones.

If you checked and your phone is still in normal mode, then we advise you to check the volume mode settings.

Setting Volume Modes

Sometimes you need the phone not to make any sounds, for example, while in a meeting, but sometimes, on the contrary, on the street you need it to ring much louder, because you can’t hear it because of the noise around it. To do this, we advise you to adjust the sound on your phone in a way that suits you.

In order to turn on the full sound of your device, you must select one of the loud or sound modes. For example, turning on the "Outdoor" profile sets the maximum volume.

Silent mode

Silent mode on your iPhone turns off the sounds that work for the "Calls" and "Alerts" functions. This mode is the most commonly used among users, you can turn on the silent profile using the toggle switch, and a notification icon will appear on your screen that the phone has switched to the silent profile. But do not forget that the alarm clock you set will still ring at the set volume, even switching it to the silent profile.

Do not disturb mode

This profile is especially useful when you are sleeping or visiting a museum or church. This mode will give you the feeling of not having a mobile phone at all. By putting your smartphone in this mode, it will, as before, receive messages and calls, but it blocks sound alerts, a light signal and “vibration mode”. You can turn this mode off, as well as turn it on, in the sound control panel. But do not forget that the alarm clock application will still sound at the volume you set, regardless of the mode.

Separate settings

If you are not satisfied with any of the modes or you have a desire to change some functions or vibro, you will need to study the settings for each mode separately. By entering the mode parameters, it becomes possible to set the volume for ringtones, messages and notifications; ringtones for system notifications and messages by default.

If you are an auditor by nature, then you might like that the phone reacts with a sound when you press the screen or keys, which can also be edited in the profile settings. The vibro feed and its sound character are also regulated there.

For each mode, you can choose your own settings and melodies, so it becomes possible to create your own mini-uniqueness.

iPhone Sound Problems

Faced with the problem that your smartphone is frozen at maximum volume and you can’t do anything about it, or vice versa, it doesn’t want to play melodies, but just makes a “vibrate” sound and all the previous tips didn’t help you, we will try to tell you a few methods how to fix this error.

Reset sound settings

Most often, a problem with sound or the fact that it does not work on an iPhone is very easily solved by resetting the sound settings. Unfortunately, all the modes you configured earlier will be reset to the default, but you can configure them again. This process is not laborious and will take you very little time and it can be done at any place and time that suits you.

1 The first action you will need to press and hold for about four seconds is the sleep button, which is located at the top of the smartphone. 2 After you need to move the scrolling line on the screen to the Off position, after which the display will go out or the wait sign will be displayed, and then the smartphone will turn off. 3 Now you need to repeat the first action, press and hold the sleep button, which is located at the top of the smartphone, for about four seconds, until the Apple logo appears on it. 4 The final step is to check and adjust the volume by listening to a melody.

Master reset

The most radical method in this situation is a general reset. Before doing this, be sure to back up all your personal data so that they are not erased from the phone during a reset.

Content:

To turn off sounds, vibration, and light alerts on your iPhone, turn on silent or do not disturb mode. Silent mode changes the sound alert to vibration, while Do Not Disturb mode temporarily blocks all alerts (including vibration and light alerts). Customize your iPhone settings to get exactly what you want from it.

Steps

1 Silent mode

1 Familiarize yourself with the concept of silent mode. iPhone silent mode mutes calls and alerts and replaces them with vibration. Silent mode is a quick and convenient way to silence your phone (most of its features).
- Note: The alarm you set in the Clock app will bypass the silent mode and ring at the scheduled time. Alarms set in other applications may not ring.
2 Turn on silent mode. The (mute) switch is located on the top left of the phone. Switching it to the “down” (silent) position will turn on the vibration and reveal an orange strip under the switch itself.
- The "up" position means that the sound in the phone is turned on.
- If you switch to silent mode and look at the phone screen, you will see a notification - "Silent".
3 Adjust your sound settings to turn off vibration on your phone. To make your phone really quiet, you can turn off vibration in silent mode by going to Settings > Sounds. Locate the "Vibrate on Silent" switch and turn it off.
- Even after doing this, your phone's screen will still light up when you receive notifications or calls.
4 Silence the keyboard. If you can still hear your keyboard keys beeping, mute them by going to Settings > Sounds. Switch the "Keyboard Click" switch from green (On) to white (Off).
5 Turn off "Lock Sound". While locking or unlocking, your phone will make sounds whether it is in silent mode or not. To turn off this sound, go to Settings > Sounds, and at the bottom of the menu, find "Lock Sound". Turn the switch from green (On) to white (Off) to mute all blocking sounds.

2 Do not disturb mode

1 Check out Do Not Disturb Mode. Do Not Disturb mode temporarily disables all sounds, vibration, and alert lights to completely free you from various distractions. When your phone is in this mode, it will receive calls and messages, but it will not ring, vibrate, or glow.
- Note: The alarm set in the Clock app will ring even in Do Not Disturb mode.
- Many people put their phones in this mode at night so that they are not woken up by a sudden vibration, ringing, or phone backlight.
2 Swipe your finger across the bottom of the screen. This will open the phone control panel.
3 Click on the crescent shaped button. This button, located at the top of the control panel, turns on Do Not Disturb mode. If this button is white, then the mode is enabled. Tap it again (so it turns gray) if you want to turn off Do Not Disturb.
- You can also enable this mode by going to Settings > Do Not Disturb Mode. Place the switch next to the "Manual" option from white to green.
- On the control panel, there is another similar icon of a crescent moon inside the sun. This button enables a feature called NightShift.
4 Turn this mode on and off at a specific time every day. If you use Do Not Disturb every day, then program your phone to turn Do Not Disturb on and off automatically at certain times of the day. Go to Settings > Do Not Disturb Mode. Turn the switch next to "Scheduled" from white to green, and then manually set the "From…" and "To…" times.
- For example, you can set working hours (from 9 am to 5 pm) so that the phone does not distract you at work.
5 Allow certain phone numbers to disturb you when do not disturb is turned on. By default, contacts that you have defined as "Favorites" will be able to reach you in this mode. You can change these settings in Settings > Do Not Disturb Mode > Allow Calls From.
- Choose from Everyone, Nobody, Favorites, or All Contacts.
6 Allow me to call you. By default, the "do not disturb" mode allows you to dial people who call with an interval of up to 3 minutes. This setting is for emergencies, but can be turned off.
- Go to Settings > Do Not Disturb.
- Look for the toggle next to the Recall option. Leave it green to enable the feature, or switch it to white to disable it.

Good time! I don’t know why you needed to conduct silent shooting (for example, I was never annoyed by the characteristic “click” of the camera shutter) on your iPhone, but I really hope that for some good and kind purposes - as our beloved sports minister says, “everything there should be no criminality ":). And if the goal is good, then you can help! After all, that's what this site was made for!

In fact, there are quite a lot of ways to turn off camera sounds (and not just through the settings, as it might seem at first glance). What are these methods? Now we will deal with all this ...

Let's get started!

How to remove sound when taking photos without jailbreak

To take pictures in silence, it is not necessary to hack the iPhone and do other incomprehensible things. All actions are easily and simply performed without using a jailbreak:

Perhaps this is all from simple methods, it will move on to more cardinal decisions ...

Disable Camera Shutter Sound with Jailbreak

Well, to be more precise, by replacing the corresponding file. A jailbreak is only needed to gain full access to the system and get to the file responsible for the sound when photographing. How to jailbreak, I will not tell you - here in a nutshell it will not work. Therefore, those who have it read on, and the rest is left to use the methods indicated above or learn how to hack the device (if the camera clicks are very annoying).

We connect the iPhone to the computer and using any file manager, for example, iFunBox or iFile, open the folder along this path /System/Library/Audio/UISounds. Here you need to find the photoShutter.caf file.
Change its name to any, it's better to just add 1 digit. After getting something like photoShutter1.caf. What is it for and why can't it just be removed? Just in this way, you have the original file and you can always return it back.
Download this file (link to Yandex.disk) and replace the original photoShutter.caf with it.
We try to take a picture and are glad that everything happens without sound!

Why do all these troubles with jailbreak, file system and other things?

The fact is that there are such iPhone models on which the sound cannot be removed in any way other than this. They are intended mainly for sale in the markets of Asian countries (Japan, Korea, etc.), where such things are prohibited by law, which means that it will not work out in the usual ways.

The method mentioned above solves the problem completely. That is, the camera will never have sound. Well, or until you do all the operations in reverse order.

The iPhone is one of the most reliable phones of our time, but even it can break. You may notice that switching to silent mode and back will be done every other time. Or even the Mute switch will move without resistance, with no mode switching at all.

In this case, the normal use of the iPhone will be difficult: when the call sound is turned off, you can miss an important call, and the inability to turn on silent mode can lead to an unpleasant situation due to a loud call during a meeting or other official event.

Why is the mode button not working?

There are several possible failures:

button malfunction;
loop malfunction;
vibration motor malfunction;
electronics failure.

The easiest option is a button malfunction. It may fail due to dust or liquid ingress, as well as due to normal mechanical wear. In the first case, it is enough to rinse and clean the button, and in the second, it will need to be replaced.

The loop is harder to deal with. On the one hand, a breakdown can be simple (detached or oxidized contacts), and on the other hand, a break in the conductor inside the loop is possible.

Vibration motor malfunction is rare, but it can also fail due to liquid getting inside or due to impact when falling. The vibration mode will not work in this case. In this case, the vibration motor must be replaced with a new one. But the burnt chip is considered the most difficult. If it is easy to replace a button or a cable, then the microcircuit will have to be soldered.

How can I fix the Mute switch?

In simple cases, you can fix the problem like this: disassemble the iPhone, rinse the contacts of the button and cable, if necessary, order a new spare part and replace it.

But to perform this work, you need to have at least elementary experience with complex equipment, otherwise you can simply break the latches or even order a spare part from another model. There is also a risk of buying a non-original part with a short lifespan. Well, replacing the microcircuit will require the use of a soldering station, so such an operation is not carried out at home.

Therefore, it is better to turn to professionals, such as the employees of our Total Apple service center. We can repair any Apple gadget. At the same time, we use only original spare parts, so we provide a maximum warranty period (3 years) for both parts and labor.

Fair, not too high or too low. There should be prices on the Service website. Necessarily! without "asterisks", clear and detailed, where it is technically possible - the most accurate, final.

If spare parts are available, up to 85% percent of complex repairs can be completed in 1-2 days. Modular repairs take much less time. The site indicates the approximate duration of any repair.

Warranty and Liability

A warranty should be given for any repair. Everything is described on the site and in the documents. A guarantee is self-confidence and respect for you. A 3-6 month warranty is good and enough. It is needed to check the quality and hidden defects that cannot be detected immediately. You see honest and realistic terms (not 3 years), you can be sure that you will be helped.

Half the success in Apple repair is the quality and reliability of spare parts, so a good service works directly with suppliers, there are always several reliable channels and a warehouse with proven spare parts for current models so that you do not have to waste extra time.

Free diagnostics

This is very important and has already become a rule of good form for the service center. Diagnosis is the most difficult and important part of the repair, but you should not pay a dime for it, even if you do not repair the device after it.

Service repair and delivery

A good service values your time, so it offers free shipping. And for the same reason, repairs are carried out only in the workshop of the service center: it can be done correctly and according to technology only at a prepared place.

Convenient schedule

If the Service works for you, and not for itself, then it is always open! absolutely. The schedule should be convenient in order to be in time before and after work. Good service works on weekends and holidays. We are waiting for you and working on your devices every day: 9:00 - 21:00

The reputation of professionals consists of several points

Age and experience of the company

Reliable and experienced service is known for a long time.
If a company has been on the market for many years, and it has managed to establish itself as an expert, they turn to it, write about it, recommend it. We know what we are talking about, since 98% of incoming devices in the SC are restored.
We are trusted and passed on complex cases to other service centers.

How many masters in the directions

If you are always waiting for several engineers for each type of equipment, you can be sure:
1. there will be no queue (or it will be minimal) - your device will be taken care of immediately.
2. You give Macbook repair to an expert specifically in the field of Mac repairs. He knows all the secrets of these devices

technical literacy

If you ask a question, the specialist must answer it as accurately as possible.
To give you an idea of what you need.
Will try to solve the problem. In most cases, from the description, you can understand what happened and how to fix the problem.

If the vibration switch on the iPhone 6 is broken, the operation of the gadget can lead to a number of oddities. The inability to turn off the sound on the phone makes it difficult to stay at meetings and official events. If the iPhone 6's silent mode button is broken, frozen in vibration mode, the owner cannot avoid a series of missed calls. That is, such a trifle can cause great discomfort.

The vibration switch on the iPhone 6 is broken: what to do?

If the mode switch on the iPhone 6 is broken - it starts to stick, move freely without a click, or does not affect the activation of the vibration mode - it's time to think about replacing the Mute button. The iPhone 6 is a solid and durable build, but it's not immune to wear and tear. After all, prolonged or intensive use is the most common cause of failure of buttons and switches.

In addition, replacing the vibration switch on the iPhone 6 may be caused by water ingress into the device or mechanical damage. In any of the cases, the cable connected to the button is damaged. Replacing the iPhone 6 vibro switch cable will not cause difficulties for the master, but for a person without special knowledge it can be a big problem. After all, this task requires a lot of professionalism.

To repair the iPhone 6 mode switch, you will have to disassemble virtually the entire phone, replace the element and reassemble the gadget. Are you sure that you will complete this task carefully enough so as not to cause further damage to the smartphone? One way or another, if the mode switch button on the iPhone 6 is broken, then the most reasonable way out is to contact the service center and the help of a professional wizard.

Our service center carries out diagnostics completely free of charge. After a comprehensive check of the phone, we will inform you what kind of repair of the iPhone 6 and the broken vibro button is needed in this case. More often, the repair of the iPhone 6 mode switch is limited to replacing the cable, less often it is necessary to replace the vibration mode switch as a whole. Regardless of the breakdown, the work takes no more than one hour.