What to do not broke the headphones. We repair headphones

Each of us once faced such an unpleasant problem as a breakdown of headphones. Most often, telephone headphones are faced. This is connected with constantly deformation of a thin coupling wire that twisted and rewind each time the device is removed in pocket or bag. From frequent beggars The core of the wire can break, and then one or both earnings cease to reproduce the sound. Consider how to fix your favorite headphones if their wire broke.

To repair the headset with the interrupted wire, the owner needs to be stocking a suitable tool and determination to bring the case to the end. Having found a breakdown, first of all it is necessary to find out in which of the wires the gap. Specialists are resorted to the multimeter, the test.ru or a voltmeter.

Check for the boron of the wires are carried out as follows.

There are cases when the device never ceases to feed signals - this means that the problem is not hidden in the cable, but in the speakers themselves.

How to restore the broken wire

If the study showed that the cable was still broken, it would have to connect it. This procedure is carried out in several stages.

Many owners in the breakdown of the headset are interested, and whether the repair of headphones is possible with their own hands without soldering iron. Specialists answer - no. All wires require reliable spike to provide stable contact. Twist, not fixed by the solder, will constantly disintegrate, the quality of sound and speech does not go.

Repair of the headset with the function of adding sound and microphone

Headphones, equipped with a microphone, do not have fundamental differences from standard system. However, to know how to make them workers, you need to understand in some nuances of functioning. The causes of problems in such a headset, as well as in ordinary headphones, can be the breaks of wires, failed plugs or broken headphones membranes requiring replacement.

Sometimes exotic breakdowns occur in the form stretching wires. This situation is not typical, since in the usual life of the wire is rather crushed than stretching. The damaged section of the cable in this case is good enough - in this area there will be a significant thinning of the vein. You can fix the breakdown with the help of an already familiar soldering iron. Remove isolation and protective lacquer with wires. Experts say that it is possible to do this with a candle or lighter. After that, there is a logging of their ends and a reliable spike - the repair of the headphones is over with their own hands.

For additional protection, you can cover the solder with a new layer of protective varnish, it prevents oxidation and minor damage.

Restore torn headphone wires is easier than it seems, however, it is necessary to spend some time. Fight all the necessary materials so as not to interrupt the process and not leave the bare parts unattended. Be careful with fine wiring, because they are very easy to damage with impressions or knife.

In order to quickly repair headphones, it is worth preparing tools and materials. If they are big and attached on small cogs, then you should choose a suitable screwdriver. Also need a stationery knife, lighter. It is possible to connect the parts using the isol, epoxy glue, but it is better to use tubes that have a heat shrink function. Turning wiring connect most often with a soldering iron. With others. Parties can and do without it. Wires are cleaned, and then twisted together. From additional devices you may need a multimeter. It easily determines the place of the cliff.

Breakdowns often occur due to breaks inside the cord and low quality assembly. You do not need special skills and tools to eliminate them. You may need a screwdriver and soldering iron. To begin with, it is necessary to find out what the problem is and finding the place in which the breakdown occurred. We will analyze the most frequent options and ways to eliminate them.

Next, you can act differently - in accordance with where the breakdown is located. If the wire break occurred inside the headphone, then it must be promoted. In large usually use screws. Little headphones-droplets can be revealed using a conventional sharp knife. They usually glue on the sides.

In an open earphone, the wire break is also determined by the power. Walk throughout the cord and listen to the sound. After you found the desired place, you will need to cut off the wire below it. Then the cord is read up to the wire and solder it in the same way as it was originally. Many headphones are tied to the node. If the wire is clicked in this way, then after circumcision it must be tied, and then solder. Check out the sound in the headset. If everything is in order, then collect it back. In the case when it does not work, use epoxy glue.

Also, the wire can break inside the plug. This problem is also audible in working headphones when palp. In such a situation, you need to get to the inner wire and cut it in the right place. Pre-plug cleaned from rubber. Next, see the location of the wire and connector. The non-working site is cut and soldered. Instead of the scratched rubber on top of the plug, make a "shell" from epoxy. Additionally, on top, the plug can be wrapped with threads or use a plastic shell from thick wire.

This situation is very common, since the cord is formed during use. As a result, the wire headphones are broken in these places. Also, the problem arises near the foundation. The output in this situation is one - to find a break and cut the non-working part.

Turn on the headphones into the connector and play music. Follow the cord with your fingers. Special attention is paid to those places where obvious bends can be seen. In the non-working segment to the headphones there may be hoarse or seeding sounds. Using a knife, cut the cord below the right place. Clean the wire. Spread the plots. The clutch space can be strengthened with a tone of the cord. Rubber bushings are better looking, which are sold in radio components. They are hollow tubes that are tensioning on top of the cord.

If the sound does not pass, then the case in the deformation of the membrane. In this case, it must be disconnected and gently straighten. Then the surface of the mesh is thoroughly wiped with a cotton disk with alcohol. The membrane is connected back, the housing is closed.

To begin with, take a small ball. From this amount of silicone, roll striped-sausage. Then wrap it around a poorly running headset. If the rim is too long, it should be trimmed with a stationery knife. Fingers give Silicon the desired shape. All the same thing we do with the 2nd earphone. Leave Silicon for 1 hour. For solidification.
Several tips:
If a wire breaks below the beginning of the branching of wires going to headphones, then it is worth paying attention to the correctness of their twisting. Inside the cord, you will notice that they are connected in pairs of color. After circumcision, they sold them on the same principle.
If you do not have a soldering iron, and the cliff occurred inside the cord, then connect the wires using a simple twisting of the spiral. To do this, take both wires and clamp your fingers. Then fasten their tips, rotating them together.
More reliable twisting - linear. Place 2 wires parallel to each other. Connect them so that the tips wrapped the opposite wire on the helix from top to bottom.
Sometimes it is very difficult to determine the location of the wire cliff. It will help to solve the problem of the multimeter. To begin with, with the help of a stationery knife make an incision in the estimated place of the cliff. Then neatly pull the wires. Next, it is necessary to remove the plastic to which they are covered. The easiest way to make it a lighter. When a little plastic comes down from the wire, attach to the alleged non-working multimeter location. He will show whether the site is really damaged. In this case, the multimeter should work in resistance mode.

In order to fix the headphones yourself, you need to determine the type of problem. Most often occurs the wire inside the cord. This happens because of the beggars. Common principle Actions when the break is simple. It is necessary to find a plot on which the wires were combined, trim it and re-connect with a working part. Also, one of the headphones may not work due to clogging and deformation of the inner membrane. It must be disconnected, wipe with alcohol and straighten.

Why doesn't one headphone work and how to fix it?

Any technique has a shelf life, and many consumers have come with this. In order not to shorten the already short life of the devices, the owners try to be careful in handling them, which is not always possible. A headset is particularly susceptible to listen to music, because every fifth person does not leave the house without a player or a smartphone, under the eyeproken driven by tracks.

At such moments, it's offensive when the sound does not work in one earphone. This trouble does not allow to fully enjoy the trip somewhere, and in general the mood will deteriorate for the whole day. But what to do?

Causes that do not depend on the headset

It also happens that the device itself is fully operational, and the wines of the whole-waveness of its owner or incompatibility with the player. There may be several such options:

loosely entry of the plug in the connector;
contamination of the dynamics of ear gray;
absence required drivers on the smartphone / PC;
too tightly stuck plug ("magic" of some laptops).

These are not all the reasons explaining why one headphone does not work. But to deal with them the easiest way, because of which they are considered in the first place.

Problems with entering the nest

It would seem that the reason is rather stupid, isn't it? But no, most often it is she who is a guilty of malfunction. To exclude a similar version of the development of events, you need to check how tightly the plug is inserted into the connector of the reproducing device. If the headset is not fully entering the socket, it immediately becomes clear why one headphone does not work.

Contacts responsible for the transmission of sound are made in the form of a rings that swinging the pin. If it enters the connector not until it stops, the connection between the "ears" and the player is broken, since the elements needed to play signals do not come into contact with each other.

However, there is a reverse situation. Sockets of some laptops may not be suitable for the plug-in headset. However, everything will work, if it is slightly pulling the pin so that its small part is visible outside.

Lack of drivers

Why does not one headphone work when connecting to a specific device? Everything is simple: sound drivers are incorrectly functioning or not installed. Because of this, audio equipment conflicts with operating system Gadget and the connection of the headset causes all kinds of trouble.

You can eliminate them by installing the software that comes on the disk bundled with the "ears" or available for downloading on the official website of the manufacturer.

Why doesn't one headphone work?

Among other things, the cause of the owner and simple model Headsets. If the holder of headphones-drops (meaning the form) is engaged in sports or other hard labor in them, after a couple of months, the speaker will be abandoned by ear gray. And it will certainly affect the sound.

In this case, it remains to thank only simple design Headset, which is easy to disassemble and clean if necessary. But it is better to keep track of the condition of the device carefully, so as not to face such a problem when one headphone does not work.

How to fix a damaged headset?

If all the light options were considered, but none of them caused a breakdown, you will have to take a serious thing. It will take carefully to examine the cord, forgive it and bend it several times at different angles near the plug or headphones speakers. Of course, when confirming concerns with them, it will have to part, but it is possible to make the device to work a little longer possible without replacing the headset.

Faulty part of the old cord is required to trim, clean the wires and twist with the balance of the entire cable.

Wireless device

The measure described above should help in the case of a damaged wire (if one headphone does not work). How to fix a bluetooth headset? The answer, unfortunately, does not encounter. This technique is most often not intended for independent repair by the owner, and something will be done only in the presence of certain knowledge in this area. Therefore, you have to replace the device or access specialists.

Most often, such a problem overtakes Sony's headphones (one headphone does not work), but at the expense of high cost, the warranty service centers solve any similar breakdown. The same applies to other headsets issued under well-known brands, so it is not necessary to despair. But if the purchase cost cheap, replacing the device to the new will be much easier and faster.

Everyone praises that he is a master of all hands and is able to find a problem in a few minutes and fix any technique. But in fact, few people know what to do if one headphone does not work. Not to mention more serious faults. It is just great when the child was taught as a child in childhood. If this does not happen - you have to independently catch the missed, method and error.

How to fix headphones?

And so that the errors were less than, before starting active actions, it is worth reading thematic articles. Of these, you can find out that most of the headphones are connected:

With incorrectly configured drivers.
With a cliff of the wire.
With impaired integrity of the sound membrane.

With the first cause, users occur most often, it is enough to eliminate it:

Go to the official website of the manufacturer.
Download licensed driver For their headphones.
Following the elementary instructions to install it on your computer or laptop.
Reload the system.

If the problem is not related to software, faithful to just longer:

Prepare everything you need. Knife, soldering iron, tape - Most likely it will be limited to this small arsenal.
Connect the headphones to any sound system and start tapping the wire, while working.
As soon as the sound changes and characteristic noises or crackle will appear, you can be sure that the source of problems found.
Cut the wire below this area, clean it from rubber.
Then the soldering iron will go to the move, it is desirable to have some experience with this device. Spread two bare areas.
You can give a normal type of cleaned wire using the isol, the fastest and fiscal option.

We cope with the membrane

If reinstalling the drivers and tacking the cord throughout the length did not give any result, you can go to the next stage:

Disassemble headphones. If they are fixed with the help of cogs - a screwdriver or blade of the knife itself.
Explore the internal contents, perhaps, the gap is located directly in the earliest itself.
Check the membrane. This is a small plate into the mesh, it is difficult to confuse with something else.
The membrane can be contaminated or bent. In the first case, rinse it with alcohol, in the second - try to straighten yourself.

As in medicine, it is necessary to adhere to one just the rules. After your intervention, the situation should not be worse. Therefore, if you are expensive equipment, and in your own skills you are not too confident, it is better to visit service center. Work on the warranty coupon will not cost you exactly anything.

Headphones on the front panel do not work

The problems with the front panel are found due to two major troublegrowth groups:

Malfunction is associated with a computer

Malfunction with headphones themselves

Check out the presence of drivers.

Check if the connector is that you insert the plug.

Make sure the front panel is properly connected to the motherboard.

With the help of the already described actions, see the performance of the headphones.

Right in the BIOS settings.

Try checking them on another computer.

Just restart the computer.

Connect other work headphones to the same panel to understand what exactly the problem is.

Most often, people are confused by the connectors on this front panel. As a result, headphones are connected to the microphone channel and vice versa. It may even be that the plug sits loosely in his nest, sometimes quite a little more pressing. Do not forget about the settings of your mixer, going into them, you will find which equipment sees the system whether it is connected correctly.

Microphone does not work on headphones

Trying to say something in Skype., and the interlocutor you can not hear? To fix the microphone on the headphones is enough:

Make sure that everything is installed required drivers And the equipment is correctly connected.
Download new version Drivers, install and restart the system. While the computer restarts, you can check the conformity of the connectors. Usually they are marked with flowers, so it will not be difficult to make a dual blindon.
If you have other equipment, with which you can check the operation of the microphone - do it. So you can understand what exactly the main problem lies.
Use Windows? Then there is a special realtek Manager HD, the window of which will come out with each connection of headphones and microphone. While you do not click a pair of buttons in this window, the new equipment will not start working, so do not turn it before time. Yes, and the settings check does not hurt.
If the warranty period does not expire, you can not hesitate to attribute headphones to the service center. Let experts spend their time and understand.

Headphones on a laptop do not work

Laptops Although they are in a separate category among the entire office equipment, but the headphones have problems with their users arise in all the same reasons:

Malfunction of headphones themselves. Cable breaks or membrane deformation.
Mallings with port.
Changed settings Realtek HD. or Bios..
Lack of special software.

When you broke one earphone:

It should be understood that the problem is related to the equipment. No drivers or settings are specifically on the left or right ear.
We'll have to work hands and besides performance, we also have been important appearance fixed product.
Investigate headphones needed consistently, ranging from the plug.
Cable stripped from rubber can be covered with a special hollow tubule, they are sold in any radio market.

Not enough only in the theory to know what to do if one headphone does not work. Without practical skills, it is better to take the repair of only cheap headphones, and more expensive equipment can be attributed to professionals if you have no experience in this matter yet.

Video: If there is no sound in the headphone

Collection of answers to your questions

The use of materials is allowed only with the consent of the copyright holder. The information on the site is familiarized and is not a guide to action. Before applying medical recipes, be sure to advise with your doctor.

Noticed a mistake? Please let us know! Highlight it and press Ctrl + Enter. Thank you!

What if one headphone does not work?

How to be? Is it possible to come up with something?

Faced with such a problem. In my case, one earphone did not work because a little wire was damaged. It was possible to solve the "surgical" path, that is, cut off the damaged area. This method can be applied if the headphones are expensive. If the price is not high, you can just buy new ones.

And also, as an option, the pin from the headphones is poorly inserted.

Question, what to do if one headphone does not work, I think almost everyone asked himself at least once in his life. It's a shame, of course, because everyone is accustomed to stereo sound, and listen to one ear inconvenient and unusual.

The reasons are why one headphone does not work, Usually only two: first, the wire broke into one of the headphones. And secondly, sometimes the jack plug bends and simply no contact with one channel.

By the way, the second reason almost no one takes into account, and it happens not so rarely, the plug is sleeping easily.

Therefore, in the second case, the plug is needed to straighten, better by passage. And in the first - try to get to the rupture and secure. I warn you: it's not so easy to do, I tried. And not long.

Therefore, the third option is to just buy new headphones.

This is a daily problem, as the headphones are mainly bought cheap. And if one of them does not work, then the best way In this case, throw them away, or listen to music in one earphone, which is completely unusual for those who love the stereo sound.

It is best to buy more expensive headphones, with them such a casus is rare.

Such problems are far from uncommon. The fact is that if the headphones are not too good quality, it is very often so that the wires inside are broken, because they are so thin there. In this case, the headphones under the replacement. Of course, it is possible to disassemble and see if the postings from the solder did not break off in the earliest itself, I do not exclude the breakdown option there. In this case, you can fix it yourself.

My headphone did not work because of the bad contact of the wire. Then just twisted and disassembled. Everything has earned. It was still correctly said above that bad headphones are inserted. Sometimes enough just to twist the headphone plin in the connector and everything comes to normal. If you can see on the computer in the speakers settings.

If you checked the connection with the device, they are tightly stuck and everyone else, then it is most likely damaged by some of the small conductors directly in the "ear" itself.

Of course, the case is painstaking, but you can try to cut a damaged area, clean the wiring, twist and wrap the tape.

It often happens that cheap headphones break, and the reason happens more often in the wire it happens that there has occurred a wire break or contact somewhere, of course, the wire can be soldered, but if the headphones are cheap, it is better to buy new ones, but if the headphones are expensive to contact the center Repair technology.

If it does not work on any device, you can already do anything.

But it happens that on the player headphones work well, and only one earpiece works on the computer. But if you insert the pin is not completely, then for some reason two headphones work.

Moreover, everything is fine with the settings.

Nothing amazing. Headphones we have the cheapest and quite a penny. The material from which they are made, completely poor quality. What to do? BUY is more expensive, branded and with a guarantee. Believe me, in the end it will turn out that you will save.

Always buy inexpensive headphones. As soon as one headset ceases to work, the husband, I saw, begins to shake them. Funny. Here, however, I did not recognize this method of repairing headphones, or not.

What if one headphone does not work? How to make headphones alone: \u200b\u200btips

Many know that sometimes even almost new headphones cease to work normally. In one of them, interference may appear, the sound is placed, and sometimes it disappears at all. In this situation, you should not immediately run to the service center. Most problems with headphones can be solved independently at home. With repair, even one who does not understand the technique will cope with the repair.

Repair of headphones do it yourself

The breakdowns often occur due to breaks inside the cord and low quality assembly. You do not need special skills and tools to eliminate them. You may need twig and soldering iron. To begin with, it is worth finding out what is the problem and find the place in which the breakdown occurred. We analyze the most frequent options and ways to eliminate them.

The wire break is manifested by outsiders and interference. Over time, the sound in the 1st headphone completely disappears. This situation is looking for a gap. Walk through the entire cord with your fingers, pre-connecting the headphones and turning on the music. Special attention is paid to the bend area and the field of entry of the wire in the headphone. In the right place you will hear the characteristic sounds.

In an open earphone, the wire break is also determined by the power. Walk throughout the cord and listen to the sound. After you found the desired place, you will need to cut off the wire below it. Then the cord is read up to the wire and solder it just as it was originally. Many headphones are tied to the node. If the wire is clicked in this way, then after circumcision it must be tied, and then solder. Check out the sound in the headset. If everything is in order, then collect it back. In the case when it does not work, use epoxy glue.

Also, the wire can break inside the plug. This problem is also audible in working headphones when palp. In such a situation, you need to get to the inner wire and trim it in the right place. Pre-plug cleaned from rubber. Next is looking for the connection of the wire and the connector. The non-working site is cut and soldered. Instead of the scratched rubber on top of the plug, make a "shell" from epoxy. Additionally, on top, the plug can be wrapped with threads or use a plastic shell from thick wire.

One earphone does not work: how to fix?

Turn on the headphones in the connector and play music. Follow the cord with your fingers. Special attention is paid to those places where obvious bends can be seen. In the non-working segment to the headphones there may be hoarse or seeding sounds. Using a knife, cut the cord below the right place. Clean the wire. Spread the plots. The clutch space can be strengthened with a tone of the cord. Rubber bushings are better looking, which are sold in radio components. They are hollow tubes that are tensioning on top of the cord.

One earpiece does not work with problems with a plate-membrane. They are not used in all models. Most often, such membranes are placed in small acoustic headphones, which are inserted into the ears. Problems with sound arise if the canal clogged or the surface was deformed. How to make headphones:

In the 1st case, it is necessary to reveal the case. Then disconnect the plate gently. It is a small mesh. Take a cat drive. Wet it with alcohol and carefully clean the entire accumulated dirt. As a result, no parties should remain on the surface. Carefully connect the platinum back. Close the headphone housing.

Sometimes it happens that the sound in headphones becomes quieter due to poor fit. There is an easy way to make headphones louder and more convenient. You will need a little special Sugru silicone.
First, take a small ball. From this amount of silicone, roll striped-sausage. Then wander it around a poorly running headset. If the rim is too long, it should be trimmed with a stationery knife. Fingers give Silicon the desired shape. All the same we do with the 2nd earphone. Leave Silicon for 1 hour. For solidification.
Several tips:
If the wire breaks below the beginning of the branching of wires going to headphones, it is worth paying attention to the correctness of their twisting. Inside the cord, you will notice that they are connected in pairs of color. After circumcision, they sold them on the same principle.
If you do not have a soldering iron, and the cliff happened inside the cord, then connect the wires using a simple twisting of the spiral. To do this, take both wires and clamp your fingers. Then fasten their tips, rotating them together.
More reliable twisting - linear. Place 2 wires parallel to each other. Connect them so that the tips wrapped the opposite wire on the helix from top to bottom.
Sometimes it is very difficult to determine the location of the wire cliff. It will help to solve the problem of the multimeter. To begin with, with the help of a stationery knife make an incision in the estimated place of the cliff. Then neatly pull the wires. Next, it is necessary to remove the plastic to which they are covered. The easiest way to make it a lighter. When a little plastic comes from the wire, attach to the alleged non-working place multimeter. He will show whether the site is really damaged. In this case, the multimeter should work in resistance mode.

In order to fix the headphones yourself, you need to determine the type of problem. Most often occurs the wire inside the cord. This happens because of the beggars. The general principle of action during the break is simple. It is necessary to find a plot on which the wires were combined, trim it and re-connect with a working part. Also, one of the headphones may not work due to clogging and deformation of the inner membrane. It must be disconnected, wipe with alcohol and straighten.

Dear readers, we will be glad to take your gratitude, as well as criticism and any comments. We make this site better together.

Well, I don `t know, it's hard too

I think that you do not need to bother very much if one earphone does not work, you just need to buy new headphones

Anastasia, headphones are good and expensive, cheaper to fix.

In everyday life modern man Headphones are an indispensable attribute that enjoy listening to listening to your favorite music and audiobook anywhere and at any time. Unfortunately, this gadget is not eternal and susceptible to breakdowns. In this situation, you have to think if you can repair headphones with your own hands, or better buy new ones. It is recommended not to rush to throw out old, since broken, in most cases, can be repaired at home. On how to repair the headphones independently, and it will be discussed in this article.

Headphones are a fairly simple device, so all malfunctions can be listed literally on the fingers. Frequent reasons why headphones stopped working, you can call the following:

plug;
faulty headphone cord;
the volume regulator failed.

Plug plug

If headphones broke, first of all it is worth paying attention to place connecting plug with cable. Often the reason for breakdown lies in this place. Because of the frequent bends, cable veins break, so the signal does not pass into one "ear" of the gadget or both at once. Also, the microphone may not work.

The breakdown to detect is simple enough. It is necessary when the gadget is on, try to curb the cable in the place of the estimated breakage in different directions. If the sound appears or cracks, it means that one of the live wires is interrupted. What if a problematic location is detected on the cable?

For the repair of headphones, do the following.

The plug replacement procedure is the same for any types of headset, for example, such as: Beats by Dr., Sennheiser headphones (SENHER) HD 215, Razer Kraken (Kraken) Pro, and also, for SteelSeries Siberia V2 headphones, Audio-Technica ATH-ES7 and headphones Defender.

Faulty cord of headphones

How to repair headphones when the headset cord faults? You can try to find place of fracture The internal cable lived, tackling and flexing all its sites when the gadget is running. If you hear the cracking or the appearance of sound during check, then mark this place with a marker. Next, in the site of the breakfast, the cable is cut and is cleaned. After that, the tips of thin conductors need to be soldered, observing the chromaticity, and insulate.

If the breakdown is not found, it will be necessary to replace the entire cord. In the following example, the repair of vacuum headphones will be shown.

Replacing the cord in large headphones

Large gadgets, such as, for example, Philips headphones or SVEN headphones for a computer, differ from the dynamics inserted only (membranes in small gadgets). Difficulties may occur when trying to get to the dynamics, in order to secure the contacts of the wires.

W. different manufacturers The set of ways to open them differ. It may be latches that are difficult to detect or hidden screws hidden under the soft "pads" - ambush. For example, a question often arises how to disassemble the Headphones Sennheiser HD203?

It's just done.

When repairing headphones SteelSeries Siberia, the ambush will hold on adhesive basis. You can remove them, carefully dodging a screwdriver, after which you can detect fasteners. In some models, latches are used instead of screws, which can be broken with strong juggles. If they break, the gadget cups will have to glue, after which they will become non-separable.

In the headphones Razer Kraken, the ambush is not glued, and they are simply removed.

After disconnecting them, the fasteners can be detected under the glued paper.

In the headset of Audio-Technica M30 or ES7, they also dress on the rim of the gadget cup. Not exceptions are the headphones Philips.

By the way, in the headphones Audio-Technica ES7 there are hinges for turning the cups. Therefore, if you, repairing the gadget, disassemble it, then care must be taken.

The headset Philips SHD 8600 is deprived of all flaws associated with the replacement of the plug and cable, as it is a representative wireless devices.

Volume Control Problems

How to fix the headphones if there are problems with the volume control in the form of a loss of sound or cod? In this case, you can use graphite lubricantTo apply it to the resistive layer to restore contact. After that, the headset must function without problems.

If after lubricating the headset continues to work badly, then the regulator is required to replace the new one.

Thus, in most cases, before running and buying a new headset, its repairs can be done personally. To do this, you will need a soldering iron with a thin stress and the skills of handling it.

Repair of headphones from the player on their own

An article about how in a couple of hours to repair all the faulty stereo telephones, which managed to accumulate during the operation of the player or players.

Aesthetes may not worry, it is not for them.

This article for those who are more important functionality and saving than the appearance of the connector ... who still does not see anyway except the user itself.

The most interesting videos on YouTube

In the good old days to repair headphones (phones) it was possible to buy a separate wire with a plug. When such a wire could not be bought, you could buy Chinese headphones for $ 0.30 and use the cord from them.

Anticipating that my last headphones are about to start the crack, I put on the market of radio components and several stores. The cheapest thing I found is the headphones about $ 8.

Well, and since some headphones used by me were bought even for a smaller amount, then I decided all the headphones to repair myself.

In the daily life of a modern man, headphones are an indispensable attribute that can enjoy listening to beloved music and audiobook anywhere and at any time. TO...

Modern people cannot do without technological devices that make life more interesting and more productive. Music is present in our lives thanks to MP3 players and smartphones. Going on a jog, getting to work, many listen to music. Such a pleasant time is provided by headphones, which qualitatively transmit sound and at the same time allow you not to interfere with others. On how to repair headphones, you can find out in this article.

Many are faced with the fact that after a certain period of use, headphones break. Most often one of the headphones ceases to work, which gives hope that it can still be repaired. The question is especially relevant for those who use expensive headphones.

"What needs to be done first, when a headphone broke?" - First of all, you need to find out the cause of the breakdown.

Often the cause of the headphone fault is the wire breakdown. The second prevalence problem is a malfunction of the speaker. If you carefully listen to the "symptoms", then you can determine the cause of the breakage of the rumor.

How to determine the cause of the breakdown:

The lack of sound or its frequent breaking, the disappearance says that the case is in a torn wire.
Hope and muted sound indicates that the breakdown occurred in the dynamics.
Permanent sound drops can say that the plug breaks and departs.
If the cord broke into the cord, the earphone begins to make rustling sounds.
Usually cords are broken at the location of the plug or inside the headphone.
Channel may simply clog out. To clean it, you need to disassemble the headphone and clean the membrane with the help of alcohol or hydrogen peroxide.

The breakdown and bending of the cord usually occur with constant loads. The breakdown may also lead to an increase in wire bending radius. Independent repair of headphones is possible only if the wire broke into them. But the breakdown of the speakers, most likely, will lead to the purchase of new headphones. If the headphones are high-quality and there is a guarantee, then in case the coil breaks, they can be attributed to the service center.

Headphones broke: how to make

First of all, when sound disappears in the headphones, you need to establish the cause. If this is a wire break, you need to find the place of its cliff. If it's about it, then the headphones are subject to repair.

Determine the location of the wires is very easy if the headphones reproduce the sound. To do this, you need to include music and forgive and base the wire along the entire length.

Where the sound disappears when the wire is flexing, there is a broken element. It will be easy to fix the breakdown. Part of the broken wire is removed, and "healthy" elements are again connected with a soldering iron. Sometimes the wire breaks in the connector, then most likely it will be necessary to replace the plug.

How to repair headphones:

Open the earphone.
View the membrane. Smiling membrane must be dissolved.
If dust and sorts got into the membrane, it must be cleaned.
Alcohol wipe the grid that separates the membrane from the space.

The problem may be in the gap lived. To restore them, you need to fully disassemble the headphones. Different headphones can be fastened differently: elements can be attached with plastic latches or screws. Some headphones are fastened with glue. After the headset is open, it is necessary to remove unnecessary residues of the wire, his sweeping and spike.

Why headphones broke out

Those part of the headphones use, they know that they are used to break. Often the headphones distort the sound, broadcast it with a break or stopped sounding at all. In order to understand why headphones break, you need to know how they are arranged.

Sometimes avoiding breakdowns of headphones can be - for this, they need to take carefully to use, and after each use, it is gently brusing the wires.

The cause of the breakage is mainly faulty plugs and wires. If the cable broke into expensive headphones, it can be replaced by purchasing ordinary headphones and cutting off the cable from them. If a plug replacement is needed, first need to decide on its type, and then go to search for the necessary item to a specialized store.

Causes of headphone breakdowns:

Cord inflection;
Zoom mechanism;
Cord breakdown in dynamics;
Malfunction of the plug;
The electrical connector does not work well.

To determine the cause of the breakdown, you need to open a headset. If the cord broke down and moved the contacts, they need to be simply connected using a soldering iron. When connecting the wires, you need to pay attention to the fact that the left channel must be connected to the tip of the connector, and the middle is right.

Tips: how to make headphones if they broke

From time to time, headphones for the player or the phone come into disrepair, but you should not hurry to throw them out. For example, if the headphones broke out, they can be fixed, and this can be done at home. To fix the breakdown, you must remove the insulation and the protective winding from the cord.

It is possible to do the headphone stripping procedure using special bodies or a simple knife.

Usually headphones consist of a pair of wires connected together. Each wire has a zoomed signal and a ground wire. You can correct the headphones by cutting off the non-working area of \u200b\u200bthe wire. It is important to avoid splitting the wire. To protect the electric cord from damage, you need to ensure that the pruning of the wire occurs smoother.

Repair Tips:

If one wire has been denied or one channel deployed, you can skip the circumcision procedure by directly starting the spike.
On the wires it is necessary to wear a special thermo-shielding tube, which performs an insulating function.
After twisting wires, the sealing of all connections produce.

If there is no possibility of soldering the headphones, most likely they will have to be simply changed. In order for the wire no longer bends and did not break, it can be protected at the place of repair using special glue. And in order to avoid breakage of the wires, they must be carefully worn in a pocket or bag, follow so that they do not go.

Overview: how to disassemble headphones-droplets

Headphones can work for a long time if you contact them. But over time, any wires wear out, the contact is moving away. Sometimes with your favorite headphones, it is so difficult to part that it is easier to subordinate to them and use for some time. When repairing headphones you need to be extremely careful. Because one incorrect movement - and the repair will be inappropriate.

You can repair the headphones, disassemble them, but also during disassembly, you can damage the membrane and capsule.

If cheap headphones broke out, it is almost impossible to disassemble them, because they are glued to tightly. To open the non-working earphone, you will need a scalpel or a sharp knife, which is consistent with the half of the case. After halves are revealed. You can clean the headphone housing.

How to reveal the headphones:

Open in a circle using sharp tools.
To break two halves, you need to make an effort, but so as not to break the case.
It is not necessary to cut through the headphones for a greater depth, enough half or one millimeter.
All actions need to be done carefully, which is not damaged by the headphone membrane.

Not all headphones can be repaired. For example, if the speaker broke, it is likely that it does not even be fixed in the service. Many people face the problem when Iphonian headphones break. Before buying equipment, it is important to pay attention to the presence of a guarantee from the manufacturer. Strong headphones are rare. For the mining of headphones at home is necessary in obligatory Use a soldering iron, otherwise all the repair will leave the pump.

Instruction: How to fix headphones (video)

Those who use headphones know that they are often broken. But this is not a reason to constantly buy new headphones, especially if they cost a lot of money. Before proceeding to independent repairIt is important to remember if the headphones have a warranty period. If so, it is better to attribute them to the service. For the repair of headphones at home, you will need a soldering iron and knife. First of all, it is necessary to determine the cause of the breakdown. Most often it is a wire break or speaker breakdown. Before soldering the wires, you need to determine where exactly the contacts were moved: at the top of the headphones or near the plug. After the breakdown is detected, headphones can be quickly soldered.

From this article you will learn how to fix the headphones that are inserted into the ears. To do this, you will have to replace either a plug or headphones themselves. If the cable is damaged, it can be fixed or also replaced with another. Keep in mind that in many cases the repair of cheap wired headphones will cost more the purchase of new ones, especially if you do not have the necessary tools.

Steps

Part 1

How to determine where there is a breakdown

Prepare the necessary tools. Depending on what needs to be fixed, you may need the following tools:

soldering iron and solder;
knife or scissors;
heat suplated tubes;
wire stripping tool;
multimeter.

Make sure the problem is related to headphones. Take other workers headphones and connect them to the device (for example, to the headphone connector on the computer); If there is no sound, most likely, he has been broken by headphones connector, not the headphones themselves.
- To check it out, plug your headphones to another connector and listen, is there any sound.
Find out if the cable is not polulled. Connect the headphones to the audio input, play the melody, and then bend and instill the cable. If intermittent sound is heard in the headphones, go to.

Determine whether the plug is not polulman. If the headphones are heard the sound when you press or twist (in the connector) plug, go to.

Try repairing headphones that are put on the ears. If the headphone cable is disconnected (like most Bluetooth headphones), connect it to other headphones - if in this case everything works, most likely, the problem is the headphones themselves. ; To do this, read the instructions for them to find out how to repair.

Cut the old plug. Knife or scissors place approximately 1 cm above the location of the cable connection with the plug, and then deploy the cable.
- Some cables set up plugs. Keep in mind that most of the problems with the plug occurs due to the overwhelmed wires inside the cable.
Remove the insulation (3 cm) from the end of the cable. Make it using the wire stripping tool. You will see the wires for the right and left headphones, as well as at least one ground wire.
- If you found two ground wires, they will have to be soldered.
Sore the wires in color. As a rule, the red wire is designed for the right earphone, white (or green) - for the left headset, and one or two black or bare copper wires - for grounding.
Remove the insulation (1 cm) from the end of each wire.
- If the wires are covered with enamel, skip this step.
Twist the wires of the same color. If you have found two ground wires, twist their bare ends.
- If the wires of the same color are different, make sure that the bare ends of the overwhelmed wires twisted.
Remove enamel from the ends of the wires. If the wire is isolated by enamel, burn it, touched the soldering iron by the end of each wire.
- Skip this step if you see bare copper at the ends of the wires.
Put on the housing of the new plug on the cable. At the same time, the carving inside the case must be directed towards the bare ends of the wires. (Please note that the metal plug is spinning into two parts - the case and the actual plug itself.)
- At the end of the plug must be two contacts. If you see only one contact, it is a mono-and not stereo plug.
Apply a little solder on the bare end of each wire. This is called the "tinning" of the wires; It is necessary to solder wires to the plug.
- Give the shipment completely cool before continuing.