Buggy new screen on iphone 5. What to do if the sensor stopped working - touchscreen on the iPhone

Apple company Watching the quality of parts from which its devices are collected. Almost every element is being finalized in the new generation of devices, but no one is insured against marriage or problems during operation. One of the most common faults for the iPhone and iPad is the output of the sensor. Touchscreen can refuse in whole or in part, without responding to the user's touch over the entire surface of the screen or only by a certain zone. If the sensor does not work on the iPhone or iPad, you should not immediately attract devices to the service center, often the problem can be solved on your own.

Signs of defective sensor in iPhone

In the iPhone and iPad, the display module consists of three components: safety glass, display and sensor (touchscreen). Sensor malfunctions are manifested by the following symptoms:

The symptoms described above may be present constantly or appear for a while, after which the iPhone will start working fine again.

It is impossible to use the touch device with a faulty touchscreen, and it is necessary to fix the problem immediately after it occurs. It is not always caused by the incorrect operation of the sensor, in some cases, errors in touch processing occur at the program level.

What to do if the sensor does not work well on the iPhone

If the problem with treating touches is caused software failure, I can eliminate its user device independently without resorting to the help of specialists. To do this, you need to perform a "hard reboot" of the device, climbing the "Home" and "Turning / Turning on the device" simultaneously. After 15-20 seconds, the smartphone screen will go out, after which the Apple icon lights up - this means that the reboot has occurred successfully. After the iPhone is loaded, you can test it on the quality of the sensor.

In addition, if the sensor does not work on the iPhone, you should make sure that the problem is not related to the case (or bumper) of the device. Often spontaneous pressing on the sensor are associated with the incorrectly glued film. In case of errors in the operation of the touchscreen, it is better to remove all protective accessories and see how the sensor responds without them.

Calibration of the iPhone sensor

Apple does not provide for the possibility of calibrating the iPhone sensor or iPad users. There are no tools in the device settings that would be responsible for calibration, and only the service center specialists can perform it, which is stated in the official documentation for smartphones and Apple tablets.

At the same time, some touchscreen settings in the iPhone are provided, but they only touch the models of the older iPhone 6S and iPhone 6S Plus. It is about adjusting the sensitivity of the 3D Touch function. To customize the press for execution various actions When using 3D Touch, you need to do the following:

How to replace the touchscreen on the iPhone

Replacing the sensor on the iPhone or iPad is a complex procedure that requires special skills, tools and availability of a spare part. In most cases, the attempts of self-replacement of the touchscreen in the smartphone lead to damage to other components of the device, the appearance of cracks / scratches on the case and other problems. That is why it is better to trust repair iPhone Specialists of verified service centers.

It is important to replace the touchscreen to select the service center correctly, for this, after reading the reviews on the Internet. When contacting the unverified service is a great risk that a low-quality substitution sensor will be installed in the smartphone, which will quickly fail. Verified services provide a guarantee for the completed operations of the touchscreen, which can be useful if the sensor starts to work out again.

What can be done if the sensor on the iPhone 5S does not work after replacing the screen?

If sensory screen iPhone It works with interruptions or does not respond to touch - this is one of the most unpleasant and complex problems with which the owners of smartphones can occur. This is due to the fact that working with iPhone and others apple devices Completely based on sensory functions, and this function is the main way to interact between the user and installed on the smartphone by applications of any type.

Apple took note of the increasing cases of sensor violations in its products and in new models it happens much less frequently. However, the problem did not disappear at all. Some users, after a fairly short time after purchase, notice that the sensor reacts with a large delay or does not respond at all to touch. In most cases, these problems arise from behind the LCD screen, but in some cases it helps to solve the situation to reboot the device or cleaning the connectors.

Possible Causes of Sensor Violations

If the screen does not work well on the iPhone 5S, it is necessary to figure out what caused this problem.

Causes of sensor disorders:

Too many programs and applications are performed simultaneously, which causes problems with rAM devices, which in turn slows down the sensor;
Entering the phone liquid;
Accumulation of garbage and dirt on the screen;
Dry soldering connectors touchscreen;
Malfunction of the primary or secondary touch screen control SC;
Touch screen received physical damage.

Ways to solve the problem:

Do not worry if touch screen Your smartphone does not work properly. This problem, like any other, has a solution.
First of all, you can try to remove the protective cover of the screen of your device, since it can be an obstacle.

If this does not help, you can try the following logical actions:

Restart an iPhone. If the problem with the sensor was caused by the phone's memory surge as a result of too large number running applications, the simplest solution to the problem is the restart of the device. To restart the iPhone 5S, press and simply hold the "Sleep / Power" button, which is located at the top of your smartphone housing.
Reset. If a simple reboot did not help you need to make a "reset" of your iPhone. To do this, press and hold the Sleep / Power button and the "Home" button simultaneously until the Apple logo appears. Release both buttons. The phone will turn on and must work. No data will be lost.

Signs of malfunction

First you need to figure out which problems occur when the sensor does not work on the iPhone. So, the fault is manifested as follows:

On the screen there are areas that do not react to pressing.
The display at all does not respond to touch.
After pressing the action occurs with a delay, or one touch causes several actions.
The so-called phantom clicks appear. Simply put, the phone begins to "live his life." Thus, these or other applications can be closed independently, the music is turned on, calling calls and so on.

Please note that anyone, even one of these problems indicates that the sensor does not work on the iPhone. At the same time, the situation may be gradually aggravated. For example, first stop responding to touch only individual areas on the display, and then the entire screen will start ignoring the press.

The reasons

Now it would be nice to find out which reasons lead to the emergence of faults described above. It can happen:

Due to mechanical damage. For example, your iPhone 5 fell, and the sensor does not work after that.

Under the influence of moisture. It does not mean at all that your phone should drown (although it happens). So, having climbed some time in damp (or in the rain), the device can start inadequately react to touch to the display.
As a result of the factory marriage or intervention of an unqualified employee of the Ayphon Repair Workshop.
Due to program errors.
While using some accessories.

This, of course, not all the reasons, because of which there may be problems with the sensor. But, as statistics shows, these cases are the most frequent.

It should be done first

No matter how strange it sounds, but some accessories may be the reason that the sensor does not work on the iPhone. What to do in this case? Of course, remove all accessories and check how the device is functioning without them.

So, most often problems may arise due to protective film, bumper, partially exciting screen, various brains, covers and so on. In any case, getting rid of all unnecessary, you definitely make sure that the fault has not appeared due to accessories.

Elimination of software failure

Another frequent reason for the occurrence of the sensor can act as a software failure. Fortunately, it is not difficult to correct it. This is done with the help of the so-called restart, which is performed as follows:

Clamp at the same time the "Home" key and the off button of your device.

Hold the buttons in the clamping state for at least 20 seconds.
Wait for reboot.

If everything is done correctly, a standard logo should appear on the iPhone screen. After that, wait some time and check whether the problem with the sensor disappeared.

If the reset helps, but not long

In the event that the restart procedure described in the previous section helps, but after a certain time the sensor does not work on the iPhone, then the reason should be sought in the programs installed on your device. It is likely that one (or more) from applications prevents normal operation operating system And leads to all kinds of malfunctions.

Best of all, of course, remove all third-party applications. After that, you need to restart again and check the performance of the sensor. Next, if necessary, you can set the programs you need one and test, as they affect the behavior of the touchscreen.

Sensor calibration

Unfortunately, the developers did not provide for the possibility of fully calibrating the iPhone sensor at home. However, some settings are present in the 6S models and above. Of course, we are talking about the 3D Touch function, which is responsible for the power of the presses needed to perform various actions. To configure this option, you need:

Go to "Settings".
Select the section "Basic".
Open the "Universal Access" tab.
Press "3D Touch".

Now you need to move the slider, thus setting the sensitivity of the sensor. After this procedure, it is advisable to restart the device.

Mechanical damage

It happens that none of the above manipulation helps and the sensor does not work as well. In this case, the reason should be sought in mechanical damage. Please note that this is not necessarily a broken display. Thus, problems may arise due to the deformation of the board, to detect only employees of the service center for the repair of iPhones.

We also keep in mind that the repair of a smartphone at home is extremely recommended. Not only do you lose the guarantee, you still risk to apply much more damage to your device than it was originally.

Replacement Touchscreen

In most cases, the problem with the non-working sensor is solved by replacing the touchscreen. Again, it is best to do this in a specialized service center. In the same place, by the way, you can find out how much the sensor is on the iPhone, as well as how much you will cost you the work of the master. Usually, the price of repair depends on the model (the newer, the more expensive) and ranges from 1000 to 40,000 rubles.

By the way, the operation on the replacement of the touchscreen takes no more than an hour. At the same time, the quality of the work done does not suffer from such a speed. The fact is that problems with the display on iPhones are found quite often, so the masters have already caught quickly replace damaged parts.

The defector on the iPhone does not work: prerequisites, diagnosis, repair.

Apple looks at the quality of parts from which its devices are collected. In fact, each element is being finalized in a new generation of gadgets, but no one is insured against marriage or the appearance of problems in the process of use. One of the more all-prolonged defects for the iPhone and iPad is The output of the detector is out. Tachkrin may refuse a hundred percent or partly, without responding to the touch of a user along the entire surface of the screen or only by a certain zone. If not sensor works On the iPhone either iPad, you should not take your devices to the service center, often it can be solved without the help of others.

Signs of a faulty detector in the iPhone.

The iPhone and iPad display module consists of 3 components: protective glass, screen and detector (touchscreen). Detector malfunctions appear subsequent symptoms:

It is buggy sensor after replacing the screen. Lagates the sensor on the iPhone 5. The sensor does not work. IPhone 5 solution!

Touching the elements on the display do not lead to action; The acts on the display occur with the delay, after some time after touched; Touch is processed not throughout the screen surface; Acts on the display occur without touching it: the phone itself launches the applications, the different menu items are pressed, etc.; The touch is processed incorrectly, in other words the action is not occurring in the zone of the screen, where the touch was performed.

The symptoms described above may be at all time to appear for some time, after that the iPhone will start working fine again.

Take the touch device with a faulty touchscreen is unrealistic, and you need to remove the one when it appears. With all this, it is not always caused by the incorrect work of the detector, in a number of all sorts of cases, errors in touch processing appear at the program level.

What to do if bad sensor works on the iPhone.

If the incurability with touch processing is caused by a software failure, then it can be removed by the user of the device without the help of others without resorting to the help of professionals. To do this, you need to perform a "hard reboot" of the device, closing the "Home" button and "Turning off / turning on the device". After 15-20 seconds, the phone screen will go out, after that the Apple icon will be lit on it - this means that the reboot has occurred successfully. After the iPhone is loaded, you can test it on the quality of the detector work.

Not counting if it works badly sensor On the iPhone, you should make sure that the failure is not related to the case (or bumper) of the device. Often spontaneous pressing on the detector are associated with the film incorrectly glued on the screen. In case of errors in the operation of the touchscreen, it is better to remove all protective devices and look at how the detector responds to touch without them.

Calibration sensor iPhone..

Apple does not provide for calibration sensor iPhone. or iPad users. There are no tools in the device settings that would be responsible for calibration, and only the service center specialists can perform it, which is stated in the official documentation for smartphones and Apple tablets.

At the same time, some touchscreen settings in the iPhone are provided, but they only touch the models of the older iPhone 6S and iPhone 6S Plus. It is about adjusting the sensitivity of the 3D Touch function. To configure the press strength to perform various actions when using 3D Touch, you must do the following:

Go to "settings"; Select the "Main" menu item; Go to the "Universal Access" tab; Click on the "3D touch" option, after which you can adjust the sensitivity of the screen.

How to replace the touchscreen on the iPhone.

Replacing the sensor on the iPhone or iPad is A complex procedure that requires special skills, tools and the availability of a spare part. In most cases, the attempts of self-replacement of the touchscreen in the smartphone lead to damage to other components of the device, the appearance of cracks / scratches on the case and other problems. That is why it is better to trust the repair of the iPhone to specialists of verified service centers.

It is important to replace the touchscreen to select the service center correctly, for this, after reading the reviews on the Internet. When contacting the unverified service is a great risk that a low-quality substitution sensor will be installed in the smartphone, which will quickly fail. Verified services provide a guarantee for the work on the replacement of the touchscreen, which can be useful if sensor Return again to work faulty.

Related records.

How to download video with YouTube on your phone on android.

How to make an IP camera of video surveillance from a smartphone on Android.

iPhone is disabled, Connect to iTunes: What to do.

OKEYGEEK is a site for those who are interested. computer technologyAnd wishes to know a little more than the ordinary user.

Short description

Buggy sensor on the iPhone - Apple Forum. I bought not so long ago iPhone 5. The first few days it seemed to work fine, but. It is buggy sensor after replacing the screen. Lags the sensor on the iPhone. Touchscreen is buggy - Apple Forum. It is buggy to spend in the air at a distance of half a cm from the observations, I understood why. The sensor does not work on the iPhone - causes and solutions. With a periodic manifestation of faulty work of the touchscreen on the iPhone (the sensor is buggy, you. Guys, acquired a black on 32 GB for yourself (Eurotest))) The sensor is buggy just pipets. Why does it bug the iPhone 5? Gluchet The sensor on the iPhone with what the canceled call on iPhone is;. What if the iPhone is buggy, iPhone 5, 5S, 5C, 4, 4S. Buggy iPhone, we will help in Moscow, the iPhone happens that it hangs, hangs on an apple or on iTunes. Gluchet sensor On the iPhone - Youdo. What if it is buggy sensor on the iPhone. Why The sensor on the iPhone can work well. IPhone hangs, top 3 tips, video instructions because of what. Reduced the price of 50% marked in a word why it is buggy iPhone, 5C, and also buggy iPhone 5, 5S, 5C.

The phone arbitrarily began to click on the top of the screen. Removed the film everything went, pasted another, it seemed to work, then again also, then at all the top of the screen has ceased to respond to touch. Rotate and found out if it does not notice the sensor to the screen itself not pressed. Tell me how to solve the problem, can anyone have a similar or similar situation?

Users on the iPhone, iPad and iPod are offended by the fact that the touchscreen itself is pressed on the screen and buttons, and after upgrading to iOS Beta., stopped working the touch. Today I will find out why the iRhone hangs the sensor and presses itself, and how to fix this trouble for iPhone 5/6/7.

How to fix the problem - sensor is pressed myself

Tenorshare Reiboot - free programwill solve all the hangs and problems associated with iOS 11/12, including, freezes when updating, hangs on the apple, it hangs in recovery mode, it hangs in dFU mode, constantly reboots, the screen is unexpectedly buggy and does not turn on and much more. In general, Tenorshare Reiboot allows you to fix the hang on iPhone XS / XR / X / 8/7 PLUS / 7 / SE / 6 PLUS / 6S / 6 / 5S / 5.

IPhone display is pressed by itself - Tenorshare Reiboot

Step 1. First, you need to download and run the program on your computer. And connect the device with a copmukter through the cable.

Step 2. By clicking "Log in to Recovery Mode", you can fix the smartphone screen itself is pressed using the recovery mode.

In addition, the program can correct other problems, an iPhone hung on an apple, the display does not respond to pressing, the battery is heavily discharged, the sensor stopped running, iOS 11 has turned the iPhone / iPad to the brick, iPhone is disabled. Connect to iTunes, reset the iPhone to factory settings. You can conveniently be used by this program on Windows and MAC.

There are several motors to display iPhone Or the iPad behaved correctly and did not live his life. You can install yourself without sorrowful adhesion.

Press keyboard buttons - reboot

Forced reboot - The easiest way to press itself. You need to press and hold the power and home buttons at the same time, for the iPhone 7 it is necessary to hold the power and volume while the apple appears when the screen appears. Next release two buttons while your gadget reboots. The iPhone lives his own life and does not respond to pressing - this breakdown is solved!

Fix the sensor works in itself through iTunes

Flashing - A common method corrects the problem with touchscreen with recovery iPhone, iPad. But all the information will be stern, before this action, backup copy Made in advance.

Using iTunes, the first to connect the iPhone to it. And should open main page Control your iPhone, iPad. You can see on top rash with the information "Restore" by clicking it. And iTunes automatically updates the device to latest version. After overgrowing an iPhone, the screen will stop working in itself.

If everyone does not help, then you need to contact service Center And replace the new display. And I would like to get useful advice, do not be shy, write to us!