Why the right earphone does not work on the phone. What to do if one headphone does not work

Everyone praises that he is a master of all hands and is able to find a problem in a few minutes and fix any technique. But in fact, few people know what to do if one headphone does not work. Not to mention more serious faults. It is just great when the child was taught as a child in childhood. If this does not happen - you have to independently catch the missed, method and error.

How to fix headphones?

And so that the errors were less than, before starting active actions, it is worth reading thematic articles. Of these, you can find out that most of the headphones are connected:

With incorrectly configured drivers.
With a cliff of the wire.
With impaired integrity of the sound membrane.

With the first cause, users occur most often, it is enough to eliminate it:

Go to the official website of the manufacturer.
Download licensed driver For their headphones.
Following the elementary instructions to install it on your computer or laptop.
Reload the system.

If the problem is not related to software, faithful to just longer:

Prepare everything you need. Knife, soldering iron, tape - Most likely it will be limited to this small arsenal.
Connect the headphones to any sound system and start tapping the wire, while working.
As soon as the sound changes and characteristic noises or crackle will appear, you can be sure that the source of problems found.
Cut the wire below this area, clean it from rubber.
Then the soldering iron will go to the move, it is desirable to have some experience with this device. Spread two bare parts.
You can give a normal type of cleaned wire using the isol, the fastest and fiscal option.

We cope with the membrane

If reinstalling the drivers and tacking the cord throughout the length did not give any result, you can go to the next stage:

Disassemble headphones. If they are fixed with the help of cogs - a screwdriver or blade of the knife itself.
Explore the internal contents, perhaps, the gap is located directly in the earliest itself.
Check the membrane. This is a small plate into the mesh, it is difficult to confuse with something else.
The membrane can be contaminated or bent. In the first case, rinse it with alcohol, in the second - try to straighten yourself.

As in medicine, it is necessary to adhere to one just the rules. After your intervention, the situation should not be worse. Therefore, if you are expensive equipment, and in your own skills you are not too confident, it is better to visit service center. Work on the warranty coupon will not cost you exactly anything.

If you have a Chinese handicraft in your hands for a hundred rubles - you can also practice in your skills. It's necessary to train because it is necessary on something.

Headphones on the front panel do not work

The problems with the front panel are found due to two major troublegrowth groups:

Malfunction is associated with a computer	Malfunction with headphones themselves
Check out the presence of drivers.	Check if the connector is that you insert the plug.
Make sure the front panel is properly connected to the motherboard.	With the help of the already described actions, see the performance of the headphones.
Right in the BIOS settings.	Try checking them on another computer.
Just restart the computer.	Connect other work headphones to the same panel to understand what exactly the problem is.

Most often, people are confused by the connectors on this front panel. As a result, headphones are connected to the microphone channel and vice versa. It may even be that the plug sits loosely in his nest, sometimes quite a little more pressing. Do not forget about the settings of your mixer, going into them, you will find which equipment sees the system whether it is connected correctly.

Microphone does not work on headphones

Trying to say something in Skype., and the interlocutor you can not hear? To fix the microphone on the headphones is enough:

Make sure that everything is installed required drivers And the equipment is correctly connected.
Download new version Drivers, install and restart the system. While the computer restarts, you can check the conformity of the connectors. Usually they are marked with flowers, so it will not be difficult to make a dual blindon.
If you have other equipment, with which you can check the operation of the microphone - do it. So you can understand what exactly the main problem lies.
Use Windows? Then there is a special realtek Manager HD, the window of which will come out with each connection of headphones and microphone. While you do not click a pair of buttons in this window, the new equipment will not start working, so do not turn it before time. Yes, and the settings check does not hurt.
If the warranty period does not expire, you can not hesitate to attribute headphones to the service center. Let experts spend their time and understand.

Headphones on a laptop do not work

Laptops Although they are in a separate category among the entire office equipment, but the headphones have problems with their users arise in all the same reasons:

Malfunction of headphones themselves. Cable breaks or membrane deformation.
Mallings with port.
Changed settings Realtek HD. or Bios..
Lack of special software.

The problems are eliminated according to the same schemes. Is that with the microphone everything is a little different, usually it is built into the laptop itself. Therefore, with his breakdown to cope with its own forces much more difficult.

When you broke one earphone:

It should be understood that the problem is related to the equipment. No drivers or settings are specifically on the left or right ear.
We'll have to work hands and besides performance, we also have been important appearance fixed product.
Investigate headphones needed consistently, ranging from the plug.
Cable stripped from rubber can be covered with a special hollow tubule, they are sold in any radio market.

Not enough only in the theory to know what to do if one headphone does not work. Without practical skills, it is better to take the repair of only cheap headphones, and more expensive equipment can be attributed to professionals if you have no experience in this matter yet.

Video: If there is no sound in the headphone

Headphones are an indispensable device that allows you to enjoy your favorite music in any place or listen to audiobooks without interfering with others. Unfortunately, this indispensable electronic gadget breaks quite often, especially this concerns headphones - "shells". Many consumers when breakdown headphones throw out old and go to the store for the new accessory. However, it is not at all to do this, because you can try to repair a broken device on your own. The repair of headphones is a simple work that can be performed independently.

Probably the most popular problems with headphones can be called the lack of sound in one "ear" or the appearance of a viper or rustling against the background of the sound. However, such malfunctions, as a rule, can be eliminated with their own hands. The reasons for the appearance of such problems can be different, but in 99% of cases proper approach We can handle them yourself.

Cut internal cord

The "symptoms" of the cliff live is "rustling" sound and subsequent full disappearance. This means that there was a breakdown of the vein in the place of bend. In other words, the internal damage to the cord will be arranged either at the place of transition to the "ears" or near the plug, with which the headphones are connected to any devices. If such a breakdown occurs, the headphones can be repaired independently. To do this, you need to install the exact break location, rotating the cord. If a cracking or sound appears in the headphone, then you really defined the place of breakage. Eliminate such a malfunction is very simple - for this it is necessary to cut the cord at the site of the gap, and then the disconnected ends are soldered. Then it is necessary to rewind the place of damage to the insulating tape.

The rupture lived at the cord connector. Most headphones are equipped with one of two types of connectors. The most convenient to repair the connector consisting of a rigid core and a soft cap made of rubber. During repair, it can be easily removed and proceed with connecting contacts. If you are dealing with a monolithic flexible plastic connector, then you have to cut this part with a knife. Reaching damage to the place of damage, it is necessary to clean up the torn wire and re-solder it to the breakdown. Most likely, during repair in the plug, the cavities that need to be fill out. It is best to do this with instantly hardening glue.
The gap lived at the headset. In this case, you need to disassemble the headphone. As a rule, either plastic latches or screws are used as the attachment of the two largest parts of the headphones. If we are talking about "shells" headphones, then the adhesive connection is used mainly. After the headphones are open, it is necessary to cut the wire, then clean it and fall in the same way as it was before. Making sure that the design is properly functioning again, the halves of the "ear" can be collected.

The cause of damage lived headphones is very simple - a large fatigue load is located on a small bend radius. That is, with constant beggars in different directions, there will inevitably break. The time when this happens cannot be determined in advance, it all depends on both the quality of headphones and from the accurate handling of this accessory.

Problems with membrane headphones

Signs of problems with the membrane can be called "Jacgish" playback timbre, as well as the appearance of rattling in one or both headphones. To eliminate troubleshooting this type It is necessary to disassemble the "ear" and remove contamination from the membrane. If the membrane is crumpled, you need to carefully dissolve it. If necessary, the mesh is cleared, located at the membrane. It is important to remember that troubleshooting associated with the membrane is temporary. Soon this situation may repeat. Therefore, repaired headphones, you can begin to look after a new pair.

Channel clogging

If there is no sound in the headphones, but all channels are intact, it means that problems arose due to the clogging of the channel. The reason for clogging the headphone channels is a ear sulfur, which, with each use of the device covers the mesh. To eliminate this malfunction, it is necessary to disassemble the "ear" and clean the mesh, and it is advisable to do it with alcohol. Please note that in no case you should not pour alcohol into the headphones, because so you simply damage the membrane, to restore which it is unlikely to succeed.

How to keep headphones?

Now the headphone breakdown is not a problem, since when using one of the above methods, you can independently return to them former functionality. However, you see that it is better to do everything so that they do not break than then spend time on the repair of headphones. To do this, you need to adhere to the rules for the proper storage of headphones.

The simplest I. effective way is the storage of headphones in special cases or handbags. Before hiding the "ears", it is necessary to neatly wasting them without tightening and too flashing wire.

And so that the headphones not only do not break, but did not confuse, you can use undergraduate tools, for example, winding them on the coil from under the thread. It is advisable to use a coil with a wide inside, where not only "ears" could fit, but also the plug.

Many people who regularly enjoy MP3 players and mobile phonesFor listening to music through headphones, they probably got into a situation when in one of the headphones or immediately in both, suddenly the music stopped playing. What could be the problem? 90%, this is a break of one of the lives of the headphones. Very often, the opening happens near the plug, that is, in the place where the wire during operation is often subjected to bending. There is a topic on this topic, but I decided to add something from myself.

Photo - Insert headphones

I have been bought high-quality headphones - Inserts that mercilessly exploited) during the last 2 - 3 years. About a month 2 years ago, sounded sound in one of the headphones.

Plastic plug

You can determine the place of the cliff by turning on the player and by bending the wire of the headphones, slowly moving from the plug to the headphones as soon as the sound appears, it means in this place and there is a break. Thus, the place of damage on the wire was determined, it turned out, as in the most common case, near the plug.

Metal Headphone Plug

Plug Jack 3.5. You can buy in any radio car market, there is a choice for every taste, both in the plastic case, cheap and in fully metallic, more expensive.

The following figure shows the split plug conclusions Jack 3.5. :

It is advisable, only if the headphones are high-quality, with relatively thick veins. Cheap headphones, with thin wings it makes no sense to reflect, they will last long after the repair. Determine the cross section of the veins, you can feed the wire with your fingers. If the wire is easily beaten and very soft, most likely there are the casualties there, and plastic insulation occupies most of the wire. In the wire there are 3 or 4 veins, of which one or two, connected together, it is minus or a shared wire, and on one alkalo on the left and on the right channel. Sometimes, if there are pets in the house, in particular, cats, which, as you know, love all the wires to try tooth, wiring there are smoother. In this case, the part of the wire that was damaged is biteled with a small margin, it is cleaned and nicknamed by a multimeter in sound transk mode. If the wire is then the wire and the length allows you to connect the soldering, they span the wires. The location of the wire connections is insulated with slices of isol or tape, and after this place is a piece of heat shrinking.

The heat shrinking is most often sitting after heating in diameter 2 times. In order to prevent it, you need to warm up a lighter, or if there is a soldering hair dryer, you can use it. If the cliff was near the headphone, you can operate with a knife with a knife, cut the wire, ring, make sure that the break is eliminated and reappeared. After soldering, the earphone can be easily assembled using second-hand glue.

Also installing the multimeter to the resistance measurement mode of 200 ohms, you can ring the headphones through the plug. That is, we ring the resistance of the wires, together with the fallen speakers of headphones, when touched by the leads of the multimeter to the plug contacts. Resistance during a call, on the multimeter screen can be different from 8 to 30 and more. This means that the channel worker and the sound in the headphone will be. If one on the multimeter screen, it means in the wiring. When assembling a headset, you need to not forget to tie a cable with a node, this node will not give out the wire from the headphone when tensioning. The following figure shows a compound scheme:

This figure shows a connection of wires with a plug and speakers. The speaker itself, as everyone knows, consists of a permanent magnet and a membrane with a coil of dynamics pasted on it. The ends of the coil are soldered to contacts on the dynamics. The coil remind, it is nicknamed by a multimeter in an ohmmeter mode, which means that when we touch the shorts of the multimeter to the plug contacts, we measure its resistance, or in other words we are convinced that the chain plug - the wire - the headphone is closed, and from headphones when connected to the player will go sound. In the same way, in the presence of a multimeter, but the absence of a signal source (player or telephone), you can check any headphones on working capacity. The author of the instruction is AKV.

Those who like to listen to music came across such a situation when crackling or hissing is heard in one earphone and it fails. Your task is to detect where the breakdown, and eliminate it.

Do not understand anything in the technique? Take the unit to the workshop, but most can cope with the breakdown on their own, and we will tell how to fix the headphones.

You have long chose a device of a good brand, beautiful design, and once a crackle with hiss was heard in them? So, somewhere there was a problem, for example, at the plug, and the device must be fixed.

Some immediately begin to search on the Internet or ask friends, where is the nearest workshop? In fact, nothing complicated in the repair of headphones is not, and we will look at typical problems, ways to eliminate them.

Have you ever broken headphones? Not? Most often you will find one of the following problems:

the wire cut off at the plug itself;
there is no contact with the conductor with a headphone;
the canal clogged;
the membrane broke down.

Here with such basic problems you may encounter. Diagnose the breakdown and proceed to eliminate it.

We will analyze in detail how to fix the headphones. Let's start an overview with a frequent problem.

If the headphones are inexpensive, then Jack (connector) will not be very protected. Basically, they are produced 2 species.

You will get 2.5 "or 3.5". It is impossible to say that one is more reliable than the other. Broke can be broken at one time.

To eliminate the problem, you will need to read the theory and proceed to practice. It will take 20 minutes. Consider how the plug is arranged, and the appointment of its wires hidden in the cord:

one channel right;
second channel left;
common channel.

In the wire you will detect 3 wiring, each of which comes from these channels.

Warmed wire

Signs of breakage will be such.

You in one of the headphones either in both hear a rustling, and then the sound will disappear. So, there was a break of the wire on the bend. You need to turn on the headphones and feel the entire wire with your hands. In this case, move it and rotate. In place breakdowns you will hear a rustling. It is required to mark the place where the break, marker or something else. Headphones Now disconnect from the device. Take the plumbage and reject the wiring breakdown. Clean it so that you can be soldered 2nd. Swipe and check the device. Is there a normal sound in headphones? You can closure this place with a tape.
When we carry headphones in a bag, etc., often an openness occurs at the plug. Jack the mobility of the parts is large, due to folds, and then the chances one of the wiring can break.

Introduce plug

Often, the opening can be found at the plug, especially if the headphones are inexpensive and the manufacturers are not too taken care of their protection. You will need tools, and if the plug itself has failed, you will need to buy suitable.

Let us need The following tools and accessories:

tin with rosin and naturally, soldering iron;
knife Special Stationery;
lighter;
vice;
glue;
cambrick (heat shrink).

Getting Started Plug. Required from the cable to disconnect, cutting off, Jack. Do it a little higher than the place where the wiring is broken.

The connector requires removing the interfering and unnecessary plastic, and some buy a new spill or take a whole from old headphones. Not less than 2 cm, wiring is cleaned.

Your task to know which one is left, right, common - experienced by.

Connect the wiring queues, and in what dynamics will hear the sound, on the wire (left or right). The remaining overall wire will sound on the left channel.

These veins solder on their channels. Act so.

It is required to outreach one tip of the vein, then the second.
In vice, our jack is fixed.
It is required to solder each living to a specific channel. Spikes required to protect. To do this, thread from Capron, which is in the wire, fasten directly to the plug. This is insurance for the soldered connection.
You will need a thermoshrinkable Cambrick to hide the scratched ends with spikes. It is required to cut off a piece of the required length, put on the cereal veins and hold this place over the fire, and it will take.

If you want to make protection reliable, use here 2 Cambridges. Excessly cut off the stationery knife. If you follow the recommendations, you will manage to repair Jack yourself.

If you figure it out in the headphone device, then you will manage to fix them. Confidence will appear in their abilities during work. Check what works and what is not. Start repairing.

Headphone broke

You hear that the sound was gone in one earphone or a crash appeared with noise, it means you need an inspection of the part. Open and pay attention to the membrane. If it is crumpled, then scatter, correct and she will lie smoothly.

The membrane often accumulates. Because of them, you will hear crackling crackle, and the item will fail.

The mesh, which is closed by the membrane, is required to rinse with alcohol.

If the membrane is too crumpled, it has already failed. It makes no sense to contact the workshop. She is expensive, and easier to buy new headphones than buying a new membrane for replacement.

When veins break in the headphone, they will not work.

So, the earphone is required to disassemble. Fasters will perform screws or latches from plastic. In the "shells" of headphones to connect glue. Headphones need to open, and cut the wire. Now cleaned and solder tips. It will be like before breakdown.

Now check whether the sound works in the design? And 2 halves "Ear" can be collected.

At each of the stages, you did, how do you advise experienced music lovers, but the headphones did not earn? Look at the old, cut the plug. Next you need to discourage with working riding.

If you are tied to these headphones and want to fix them yourself, then combine the details, try to adjust. Nothing managed to fix?

Purchase new headphones, care for them carefully and will not have to once again repair or throw a favorite thing. Successful to you repair and listening to your favorite music.

According to modern headphones - both inserts, and invoice, and vacuum models - rarely you can predict their service life. Manufacturers can guarantee, but at any time it may happen that one of the headphones does not work; How to repair - depends on the nature of the breakdown.

The most frequent causes of problems

If consider different types The designs of "ears", then the most frequent types of problems with them are:

Cut wire. Cable leading to one of the speakers can be accidentally killed, break or grind. This is especially likely to try the cord often.
Dynamics membrane breakage. More often occurs in the overhead models, where the dynamics of larger size and are less protected by the case.
Power breakage. It happens if it is inactively bend it, pulling out of the player or phone.
Software with sound source (incorrect installed driver, incorrect setting exit)

Each of these cases should be considered separately.

Source Sound

Before thinking how to fix the headphones, if one does not work, it is worth checking them on another sound source. Connect them to another player, smartphone or amplifier. If on another device everything is correct, then look for a problem in your player. Most often such problems are:

Shifted balance. Sometimes, confusing the balance knob with the volume, the user turns it into one direction. Then, of course, the sound in one of the channels will be at zero.
Poor plug. Particularly often with stationary devices. Check the switch.
Open inside an amplifier or DAC. Then it is necessary to repair not headphones, but the sound source.

Relief wire

You can not always immediately determine that the cable to the left or right is damaged. The gap can be hidden under insulation, externally intact. The best way Determine the gap - try to try to try the cable over the entire length, from entering the speaker to the input plug. At the same time, the music should be turned on. If the problem is detected, there may be the following effects:

There is a sound that was previously absent
The sound disappears, before that the normally published
Crash and other side effects are heard

What to do if one headphone does not work because of the cliff, it is clear: you need to fasten the damaged cable again. We bring a brief instruction:

Prepare tools. You will need a soldering iron with perhaps more subtle stall, solder, flux, and a wooden or ceramic stand for work.
Cut the cable from two sides in a few millimeters to the breakdown.
Carefully clean the wire with a knife. In the cable, three wires are usually located; If the gap is above branching on the right and left channels, there may be two. Combined manufacturers provide them with insulation of different colors, which makes it easier to repair in such cases.
Raise the stripped ends of the wire to the soldering iron. To do this, put the cleaned end to the platform for work, apply a soldering iron flux to it, and after a few seconds, make a steel of the soldering iron gesture, similar to movement when cleaning from varnish. As a result, the wire should receive a kind of solid "tip", which improves conductivity.
Put on each wire slice of an insulating tube (Cambridge). Do the same with the cable as a whole.
Spread the wires, the color of isolation on which the same.
Protect spike places by moving an insulating tube on them. Lock the tube using a lighter, slightly sending. The resulting harness for reliability can be bent in the form of the letter Z and tie the thread, which will reduce the probability of re-rupture.
Do the same with the cable as a whole. From the aesthetic considerations, you can pick up an insulating tube of the appropriate color.

This method is suitable for any of the above types.

It happens that the wire has broken and inside the hull of one of the headphones. In this case, it is necessary to disassemble the case, which is simply enough with overhead models, but difficult with vacuum or inserts. Sometimes the disassembly method is obvious. In other cases, you may need consultation on the forums, where you probably have other users of this or similar model.

For disassembly, you may need a scalpel or just a sharp knife. If the body is glued, then it will have to clamp it in the vice so that the crack appears at the place of the adhesive. After repairing glued seams, it will be reopened.

Membrane damage

As a rule, this is the problem of large models that were often mechanically exposed. From the drops of the membrane dynamics can be deformed or crack. If you have determined that it is not a cable connection, then perhaps the problem is a membrane.

Alas, it is possible to fix it yourself can only light deformations in the form of concreteness. As a rule, there is enough easy pressing that the membrane restore the form. But if she cracked, headphones need to be repaired from professionals (if they are quite expensive). Budget models carry in service. No sense - new to buy easier and cheaper.

Plug plug

Another weak place of all audio systems is a plug. Careless movement - and the plug can break into the connector of your player or smartphone. It happens, it is because of this one headphone does not work; How to fix - only the replacement of the plug.

It is important to purchase the right model for replacement: for simple headphones it is a three-contact plug, for a headset - four-contact. Since u different manufacturers The flipping may differ, specify the specialized forums, which exactly the plug model is to buy for your headphones or headset and how to connect the wires. Although the latter can be viewed in the most affected plug. In general, this is done like this:

Cut the defective plug at a distance of 5-7 mm from the connection.
Remove the insulation from the cable as a whole about 1 cm
Each of the cable veins is removed with a 3-4 mm insulation using a stationery or ordinary knife. One of the wires in each housing should be covered with paint; Take it on the same 3-4 mm.
Twist those cables that are not covered with paint, in one.
Slide the plug and put on its housing to the wire before starting the soldering.
Squash the cable twisted from two to the central pin of the plug.
Sleep the wires covered with paint, to the contacts of the corresponding color.
When the solder cools, connect the headphones to the sound source to make sure that both channels work and the stereo effect is present. It is better to use specialized test records or music with a pronounced stereo (for example, Nirvana - Rape Me, Pink Floyd - One Of These Days)
If everything works correctly, then screw the plug housing to the connector.

We hope these instructions helped you understand what to do if one headphone does not work.

Just replacing cable

If you prefer high-quality sound and expensive players or smartphones with a dedicated DAC, then maybe good decision For you will be headphones with a replaceable wire. Today there are two main standard:

MMCX connector. It has a round shape with contact in the middle, reminding the miniature version of the television antenna plug. It is used by such manufacturers like Shure, Ibasso, Fio, Dunu, Tinaudio and others.
Biook connector. Looks like two pin contacts that are inserted into the headphone housing. Applied QKZ and other manufacturers from the budget segment.

This solution has many advantages:

Light replacement. Instead of long repairs you just buy new cable And connect your headphones to it.
Affordable price. Basic models of the replaceable cable are in online stores from 300 rubles.
Large selection of cables. There are ordinary models, options with a built-in microphone, with a Bluetooth receiver, as well as audiophile - from premium materials. You can also choose the design to taste yourself.

Cherry on the cake will be the opportunity to order alteration of any headphones under the MMCX standard, so that the cable becomes replaceable. However, this option is not from the cheapest and makes sense only for premium headphones.