1- Power Input Indication
2 - Indication of recording on hard disk
3 - Indication of the operating mode (LED is on when the standby mode is turned off)
4 - Reception Zone IR receiver

* The IVR 5100S model differs from the IVR 5250s model by the layout of the components of the nodes and
The power on / off (p. 12).

A unique receiver that can: rewind the live broadcast, put a live pause to 10 hours long, store a large amount of information (250GB, ~ 220 hours of video) to record video from 5 channels at the same time, compatible with HD high definition format

Rikor TV This is "Personal Television", truly convenient for the viewer, in which the possibilities of TV and a computer are combined.

Now you have the opportunity to watch your favorite programs and films from the air at a convenient time for you, as much as possible. You can create your own television channel and your news that will show exactly what you are interested.

Excellent domestic receiver with HDTV support for Riper TV.

Construction and connection

The first thing that draws attention to the presented novelty is durable, even somewhat heavy for the household receiver, the silver body. The impressive dimensions of the device (440x290x75 mm) give the apparatus a solid look. The chassis and the case cover of the IVR 5250 terminal are made of metal with a thickness of about 1 mm.
So it is possible to say with confidence: without any deformation, the terminal will calmly "feel" if you put a couple of other homemade multimedia devices by weight of a few kilograms. We were able to make sure during testing. Despite such a "army" reserve of safety, the terminal looks quite stylish and modern. The front of the front panel of the receiver corresponds to the overall concept of the design, which is characteristic of significance and conciseness. There are no automatic control buttons on the front panel. Indication of operation modes is carried out by three dot LEDs in blue:

• power switching indicator;
• record indicator on hard disk;
• view / duty indicator.

On the left side wall of the receiver case is a power switch power switch. He is unusual. Touch contact is used to turn on the machine. In the operating mode, the sensor playground is highlighted by the blue LED.

On the right side wall of the case there are two slots for smart cards of the built-in conditional access system and a slot for installing a DVB-CI module.

The rear panel of the Rikor IVR 5250 receiver is:

• inputs of two DVB-S / S2 Tuners LNB A and LNB B, equipped with F-type jacks. Each of the tuners has a loop output;
• eUROSCART connector;
• digital multimedia video / audio interface connector HDMI;
• s-Video output (mini-din);
• rJ-45 connector ethernet interface (LAN);
• RCA-outputs of stereo audio R / L;
• coaxial RCA-outlet digital audio S / PDIF;
• rF-modulator output for connecting a TV at high RF OUT;
• transit input of RF-INF modulator;
• connector for connecting the antenna GSM module. The terminal kit includes a compact GSM antenna, installed directly to the existing connector;
• connector for the GSM module SIM card. The receiver includes a SIM card, designed to support interactive services using the built-in GPRS modem;
• uSB data port connector;
• power connector.

The recruitment of the RIKOR IVR 5250 is available from the RIKOR 5250 receiver allows it to attribute it to a group of subscriber devices equipped with multimedia features. The lack of interfaces that give the ability to switch video and audio signals of other devices, assumes some self-sufficiency presented for testing the product. Such a decision of the developer, from our point of view, takes place, since the demand of excessive interface connectors in some devices is usually low.

Layout of the receiver electrical circuit - traditional: motherboard and fee (more precisely, two boards) power supply. We failed to determine the type of processor. The radiator, glued to its upper surface, hid the label, and we did not risk it. The system board has two identical satellite DVB-S / S2 tuner DNBU24511 Samsung.

Receiver Rikor IVR 5250 Equipped with an HDD-drive of a 3.5-inch constructive capacity of 250 GB (Seagate ST32508208CE). The technical specification of the terminal states that the product can be equipped with a hard drive capacity of more than 160 GB. Given that, for full support for interactive capabilities, the device almost always should be in active mode, the developers have tried to alleviate the thermal mode of the presented product. This contributes to the placement electrical schemes The device in a fairly spacious case, equipped with a sufficient number of holes for convection, as well as additional forced cooling of the terminal power supply of a miniature fan.

In general, it has a design similar to the digital console satellite receiverhaving a video recorder and storage device on hard disk (PVR). The numeric keypad is located at the top of the console. It can be used to enter text. In the middle of the console are:

• block button buttons with OSD and cursor position management;
• digital video recorder modes control buttons;
• buttons call interactive services.

The console has small sizes and comfortably lies in hand. The signatures of the functions attached to the individual buttons are made in Russian or have a generally accepted international designation. For a user already familiar with digital satellite receiver, will be somewhat unusual that the names of some functions differ from generally accepted (for example, instead of EPG there are "IPP"). The purpose of the individual buttons does not match what is indicated in the description of the receiver, although it does not create any special problems.

A distinctive feature of the remote control of the RIKOR IVR 5250 receiver is its "learning". Using this feature, you can program the selected remote control buttons to control, for example, with TV. The procedure for "learning" is very simple and available to repeat by any user.

Capabilities:

• rework live broadcast
• puts direct air pause long up to 10 hours
• stores a large amount of information (250GB, ~ 220 hours video)
• writes video from 5 channels at the same time
• compatible with high definition HD format

Technical data: Satellite IVR 5250s, IVR 3100S

Tuner
Input connector:	Type "F", IEC 169-24, socket
Input resistance:	75 OM
Range of received frequencies	950 - 2150 MHz
Strip width if:	36 MHz
Input level:	from - 65 to - 25 dBmWT
Support standards:	DVB-S and DVB-S2
Maximum symbolic speed:	20-30 MSM / C (QPSK), 10-30 MSM / C (8PSK)
FEC support:	1/2, 2/3, 3/4, 5/6 and 7/8
Converter feeding (LNB):	+13 V (vertical polarization), +18 V (horizontal polarization) at a current to 500mA
Switching ranges:	tone 22 + 2 kHz
Protocol:	Diseqc 2.0.
Number of tuners:	2
System resources
CPU:	STI 7100.
Flash memory:	8 MB
System Memory:	DDR SDRAM 128 MB
Video memory:	DDR SDRAM 64 MB
Hard disk volume:	from 160 GB
Digital port	USB 2.0
Software Update:	OTA ("OVER-THE-AIR", through channels of broadcasting)
Video
Video decoding:	MPEG-2, H.264 / AVC (MPEG-4)
Image format:	4:3, 14:9, 16:9
Number of lines:	1080i (HD HD), 576I (standard SD resolution)
Video outputs:	model IVR 5250s\u003e TV SCART, S-Video, HDMI (digital) RF-modulator (factory setting): 36 channel, frequency 591, 25 MHz
Audio
Audio decoding:	MPEG-1, MPEG-2
Audio output:	model IVR 5250s\u003e RCA stereo (analog), S / PDIF Coaxial (digital D-audio)
Conditional access
model IVR 5250s.	cartewear: 2 connector; CI Interface: 1 Connector
network hardware
100 Mbps Ethernet:	RJ-45, socket
GSM / GPRS Module
Power Supply
Voltage:	90-260 V / 50-60 Hz
Power consumption:	no more than 75 watts
Working temperature	0 - 70 ° С
Storage temperature	-20 - 70 ° С
Permissible relative humidity Working:	85%
Storage:	90%
Dimensions (w x in x d), mm	model IVR 5250s\u003e 437 x 73.6 * x 288 / * Size with legs /
Mass, kg.	model IVR 5250s\u003e 4.65
List of equipment supplied:	IVR, SCART-SCART cable, power cable, remote control remote control, Jumper Cable, GPRS Antenna

Ricor's developers are constantly improving the firmware of receiver so they are regularly updated. Official firmware Updated straight "with ether". But the most "tasty" it is not always possible to introduce official releases for updating the firmware. The example of such behavior of the vendor is usually purely legal.

Files of unofficial firmware for receivers Rikor TV (Active TV) are situated in file storage on our site

For manual update The firmware of the Rikor receiver must create a flash drive. It is enough and very small (512 MB) carrier. In the root formatted in FAT 32 (it is possible in EXT2 and EXT3 formats, but it is through Linux, which is associated with a mass of difficulties for the unprofessional in this OS) of the flash drives are copied files with the informal firmware of RIKOR.

The USB keyboard will have to be disconnected. After the firmware it can be connected again

The prepared flash drive must be inserted in the rear panel connector, enter the main thing on-screen menu and select menu Software Update. By the way, some inconvenience with USB connectors on the rear panel can be strongly reduced insert into these connectors of the usual USB devices of the desired size and output the ends into a more convenient and affordable place.

Attention! The installation process of updates is completed automatic reboot Receiver. As a result, all current records are interrupted! First, finish the record of all necessary gears. And then you calmly flash the Riort Receiver.

Buttons UP or DOWN On the remote selection item USB(Prepared USB device It must be inserted into the appropriate connector on the rear receiver panel).

Note: Through the Internet you can upgrade to purely official version. In unofficial firmware, developers can insert some interesting opportunities for any political reasons not entered into official updates According to satellite receivers of active TV.

Press the remote button OKTo close the message.

▪ If there is a newer firmware version, rather installed, then the screen opens the dialog box Software Updateindicating new version Software available for installation.

- Press the button Refresh To start the installation process of the new version of software.

If there are no updates available, the user receives a message: " You have installed latest version BY".

- Click the window button Outputor the remote button OUTPUTTo close this window without installing updates.

Pressing the button Refreshthe boot process begins and installing on the receiver of updates. The process of installing the update is displayed on the screen using the indicator.

Attention!In no case, turn off the power of the receiver until the firmware update process is complete! After the installation process of installing updates, a message appears on the screen: "updates are successfully installed. IVR will automatically rebooted after 10 seconds."

View of the front panel IVR 5250s (IVR 5100s *, IVR 3100S)

1- Power Input Indication
2 - Indication of recording on hard disk
3 - Indication of the operating mode (LED is on when the standby mode is turned off)
4 - Reception Zone IR receiver

1. LNB tuner satellite antenna in 9. HDMI output
2. LNB tuner satellite antenna output 10. RF In Antenna Entrance
3. LNB A 11 Satellite Antenna Entrance 11. Ether Non Antenna Efficiency Out
4. LNB A 12 satellite antenna entry 12. D - Audio output
5. Slot for SIM card GSM module 13. Audio stereo outputs (L, R)
6. LAN input for connecting to local network 14. S-VIDEO output
7. Input for an antenna GSM module 15. SCART output
8. USB 2.0 input 16. Nutrition from the network ~ 220 V / 50 Hz

Attention! Make all the necessary connections, turning off IVR and the device connected to it from the power supply. Do not remove the IVR top cover if IVR is connected to the power supply.

Attention! Make all the necessary connections by turning off IVR and the device connected to it from the power supply.
Do not remove the IVR top cover if IVR is connected to the power supply.

Installing the satellite receiver RIKOR TV

Connecting a satellite antenna to a satellite receiver RIKOR TV (for IVR 5250s and IVR 3100S) (Fig. 7)

To ensure the work of all IVR functions, it is necessary to key satellite antenna To both tynem. To do this, connect the cable from the satellite converter to the input (3) of the LNB A tuner, and the output (4) of the LNB A tuner is connected to the LNB b tuner input (1) with the cable - jumpers supplied in the kit.

Note The user can also use the services of third-party satellite television operators, for example, NTV +, HD platform (Fig. 8). To do this, you need to install a third-party satellite antenna and connect it to IVR through the DiseqC switch (the type of switch is selected depending on the configuration of the home antenna system) .

The cable from the RIKOR TV network antenna converter should always be connected via a branch (direct branch) to Tuneur V. The lateral branch of the coupler should be connected to the input 1 of the DiseqC switch through the satellite PC amplifier. The amplifier is fundamentally necessary to ensure the interchange from the network antenna Rikor TV. Other cables from third-party antennas are connected to other DiseqC switch inputs. The DiseqC output should always be connected to Tuneur A. The antennas and channel settings are described in the "Settings" section.

Connect an antenna cable (for IVR 5250C and IVR 3100C)

To ensure the work of all IVR functions, you must connect the antenna cable of the television cable network (TKS) to both tynemas. To do this, you need to connect an antenna CableTax to the input Cable in 1. (1 ) tuner 1, and output LOOP 1. (2 ) Tuner 1 Connect with input Cable in 2. (3 ) Tuner 2 with a cable-jumper supplied in the kit. If the TCS antenna cable is transmitted and analog channels are transmitted, it is necessary to connect the output LOOP 2. (4 ) Tuner 2 With an antenna television entrance.
Connecting video and audio outputs IVR can be connected to a plasma / liquid crystal panel, a projector or an electric body a visor using connecting cables. Connecting cables are not included (except SCART-SCART cable). The selection of audio / video connections is determined by the model of the reproducing device.

Connect to HDMI output (Fig. 9)

HDMI is a leading digital video and sound combining standard that allows you to play high definition images in digital format. If the reproduce the mouth is supported by this format and is equipped with an HDMI input, it is recommended to connect IVR to this input. HDMI output holds permissions 576p and 1080i. At the same time, the ropes will use the certified HDMI HDMI Cable from logo hDMI type (Not included in the package). Connect one end of this cable to HDMI-output (9) IVR, and the other end to the HDMI input of the TV (Fig. 9). If the TV is equipped with DVI input, connect it to HDMI-output (9) Satellite Ricor TV receiver, using a transitional interface or a special HDMI-DVI cable (not included in the package), and connect to RCA stereo stereo-stereocabel (only for IVR 5250S and IVR 5250C models only).

Connect to SCART output

If the reproducing device has an input SCART connector, then using the SCART-SCART cable bundle in the SCART cable kit SCART. (15 ). This ensures the transfer of high-quality video signal RGB standard and stereo audio signal. If the reproducing device has A / V inputs in the form of RCA connectors, then use the SCART - 3RCA cable (not included in the package).

Connecting to the S-VIDEO (for IVR 5250s and IVR 5250C) (Fig. 10)

If you connect to the S-Video (14) exit, use the specialized S- VideoO cable (not included). At the same time, in order to eliminate the distortion of video images, make sure that the reproducing device is configured to S-Video.
In this case, it is necessary to take into account that only a video image is transmitted by S-Video with unity, it is necessary to additionally undergo to the TV audio stereo (L, R) (13). This is performed under the key with a 2RCA cable - 2RCA (the set is not included).

Connect to digital D - Audio output

To the digital D- Audio (12) (12) (S / PDIF standard), you can connect an audioxyler having a Dolby Digital decoder and equipped with a complete set of sound columns. At the same time, the sound of the received or recorded television programs, having a Dart Darth Digital, will be played in mode 5.1.
Otherwise, the sound will be played in the mono / stereo standard. Connecting to digital D - Audio output ( 12 ) is made using a specialized coaxial cable (Not included in the package).
"Dolby" and "DD" are registered trademarks of Dolby Laboratories.

Connection to high-frequency (antenna) entry for IVR 5250s) (Fig. 11)

If the reproducing device has only high-frequency (antenna) input, the connection of the digital satellite receiver Riort TV is made as follows. Antenna cable Connect to the entrance RF IN. (10 ). Output RF Out. (11 ) Connect using a high-frequency cable (not included) to the television antenna input. After turning on the digital satellite receiver, Riort TV is re-scanning the air channels of the TV. At the same time, the "additional television" channel will appear on which audio / video information from the digital satellite receiver RiCor TV will be accepted. With this connection it is possible to match the frequency of essential channels and frequency
transfer audio / video information from digital satellite receiver Riort TV.
In this case, you need to configure the antenna output of the digital satellite receiver RIKOR TV (setting the RF-modulator).

Digital Interfaces Satellite Receiver Ricor TV

The digital satellite receiver RIKOR TV has a digital interface - USB 2.0. Currently USB (8 ) IVR is used to connect any USB drive to refresh the firmware. In the future, it is planned to develop a firmware for connecting to a satellite receiver RIKOR TV through USB interface Different digital eliggers: cameras, camcorders, keyboard.

Local connection connection

A digital satellite receiver RiCorv TV has full software and hardware support for 10/100 MBIT Ethernet.
Connect the standard cable (not included in the package) to the LAN input (6), RJ-45 socket and configure the Internet connection.

Connection GSM / GPRS Module

Digital satellite receiver RiCorv TV has a built-in GPRS module, providing permanent connection through the GPRS modem to the Internet anywhere in the world where there is cellular. To use the GPRS Internet you need:
1. Insert the SIM card into the adapter (included in the package).
Adapter Place in the slot (5) (IVR 5250s, IVR 5250C), located on the rear switching panel of the digital satellite receiver Rikor TV.
To remove the SIM card from the adapter, click the button next to the adapter.
2. Attach the GPRS antenna (included) to the connector (7) located on
rear switching panel IVR (Fig. 2, 5).
3. Configure the GPRS connection with the global Internet network.

View Paid Channels

View Paper Pack Channels Ricor TV

The digital satellite receiver RiCorv TV has a built-in descrambler Conax, designed to decode paid channels of the RIKOR-TV package. You need to purchase a Rikor Access Card and insert it into the first Card Academy Connector ( 1 ) (Fig. 12) microcircuit down and until it stops.

View paid channels of other satellite TV operators (only for IVR 5250S models, IVR 5250c)

To view the paid channels of other TV operators, follow the following:

1. Purchase conditional access module (CAM) and access card.
2. Insert the access card in the CAM module.
3. Insert a CAM module with a card into the CI interface connector (3).
The module is inserted into an arrow connector drawn on the label. The surface of the module with the label should be directed down.

Note
It should be advised to consult in the service center Rikor about the possibility
Use the module itself in the CI interface of the IVR console.

Enable / disable IVR 5250s and IVR 5250c

Connect the supplied network cord to the jack ( 16 ) Located on the right on the rear switching panel of the digital satellite receiver Riort TV (Fig. 13), and insert the plug of this cord into the power outlet.
To turn on / off the power supply of a digital satellite receiver RIKOR TV, touch the Single button located on the left side panel of the digital satellite receiver Riort TV.
When power is turned on, the indicator lights up 1 located on the front panel of the digital satellite receiver Rikor TV.
Re-enable / disable the digital satellite receiver Rikorv TV should no less than 2 seconds.

Enable / disable IVR 5100s, IVR 3100S and IVR 3100C

1. Connect the supplied network cord to the jack (16) located on the right on the rear switching panel of the digital satellite receiver Rikor TV, and insert the plug of this cord into the power outlet.
2. Press the red button of the console.
3. To translate the digital satellite receiver RiCor TV in the waiting mode and exit from it briefly press the red button of the remote button.
4. To turn off IVR, press and hold the red remote button for at least 3 seconds.
Re-enable / disable the digital satellite receiver Riper TV should no less than 2 seconds.

Remote control

To control the digital satellite receiver, RIKOR TV is designed to remote control (remote control).
The remote control is suitable for all product satellite and cable digital receivers.
Insert two batteries in the remote (AAA 1.5 V). When using remote control, make sure that:
▪ on the path of IR signals from the remote control to the IR receiver 4 (Fig. 1, 4) located on the front panel of the digital satellite receiver Rikor TV, there are no obstacles
▪ The angle of deviation of the remote control from the imaginary perpendicular to the IR receiver 4 on the front panel of the digital satellite receiver RIKOR TV does not exceed 30 degrees and the distance to the digital satellite receiver Riort TV does not exceed 8 meters.

Cautions
▪ Avoid contact with direct sunlight on the receiver of IR signals on the front panel IVR.
▪ Replace the batteries in the remote control in a timely manner. Do not use the old and new batteries at the same time. Try not to use rechargeable batteries.
▪ Do not drop the remote control, protect the moisture.

Video Decorder Management Rikor TV

Interaction with interactive screens objects

To interact with interactive screens, the video recorder is the remote control. All video recorder screens are divided into interactive objects with different functionality. An interactive object can be a button, menu, list of elements, data entry field.

How to highlight an interactive object on the screen?

To move the selection cursor over the interactive screen objects, use the remote control arches: ◄ ▼ ▲.
The object is active if it is highlighted in yellow.
If the interactive object is a list of elements, the list becomes active if one of its elements is selected.

How to highlight the item inside the interactive object?

To highlight an element within an active object, for example, to highlight the list item, item vertical menu, EVERYTHING THE NAVIGATION ROOTS OF THE CONTOLOR: ▲ ▼.

How to execute a command associated with an interactive screen object?

▪ Highlight an interactive object. If the object consists of several elements (for example, a list of channels), move the backlight cursor to the desired item of this object.
▪ Confirm the selection by pressing the remote control button. OK.

Transitions between screens

To go to the desired screen, the main menu is served.
The main menu can be opened / close by pressing the menu remote button.

Messages

When interacting with interactive screens, the user receives various messages.
Messages represent dialog boxes With input fields, interactive buttons.

Dialog boxes Open on top of the main screen. The user can execute
suggested commands or close the dialog box without performing any commands by pressing the remote control button OUTPUT.

Agreements adopted in the "User Guide"

▪ The names of the button buttons are denoted by capital letters in bold. For example, press the console button PANEL.
▪ Application names, menu items and screens are denoted by bold. For example, discover Archive.
▪ The term used in the text "Select the menu item" means executing the following: Move the allocation cursor to the desired menu item and press the remote control button. OK.

Assistance system

▪ Fast visual assistance " Advisor". In case of difficulty, you can always call on the screen AdvisorBy pressing the remote control button of the same name.
▪ Use the electronic version of the user manual, help.
To do this, select Main Menu Help\u003e Help.
▪ Use the Print Version of the User Guide.
▪ Call the Center.

Receiver Management Ricor TV

Purpose of the buttons of the console *

Standby mode

To transfer IVR to standby and exit mode
briefly press the red button of the console.

Note
▪ In the standby mode, the recorded records are executed on the video recorder.
▪ If the console is not used within 5 hours, then an automatic transition to standby mode occurs.

IVR.

Button IVR. Includes video recorder control mode.

TV.

Button TV. Includes TV control mode.
In TV control mode:
▪ POL + / R-R- serve to switch channels,
▪ The A / V button includes a / v TV channel.

Switching channels

To switch to the desired channel:
▪ Dial the channel number corresponding to the channel location in the channels or channels using the digital buttons
▪ Select a channel in the channel list using the ▲ ▼ remote control arrows and click OK to confirm the duration of switching.
Button 0 Used to return to the previously viewed channel.

Select video format

When viewing a transmission to select video format: 4: 3, 14: 9, 16: 9 Press the remote button.
The selected format is saved until it reinstalling it.
* To the remote control from the video recorder can also control the TV, the remote control
"Traine"

Text entry mode

1. Using the remote control buttons
▪ Deleting a symbol before the cursor in the text input field.
▪ Selecting a font register: Capital / lowercase.
▪ Changing the sequence of diothed fonts: Latin / Cyrillic.
For example: ABVGABC2 or ABCABVG2.
▪ Button " 1 @ "Used for a sequential set of following characters:
. / @ : 1
▪ Button " 0 _ "Used to enter numbers 0 And the sign of the gap between the symbols.
A single press on this button inserts a space, and the double press enters the number 0.
The alphanumeric buttons serve for consistent selection of letters / numbers: ABVGABC2.
2. With the on-screen keyboard
To enter text, you can use the on-screen keyboard to enter the selected input field.
To open screen keyboard, Press the remote control button Claw.

Sound adjustment

1. In the TV control mode:
▪ Navigate to the TV control mode.
▪ Set the sound level by pressing the V + / V- buttons.
Regarding the sound of the sound of the visor, you can adjust the sound level in IVR control mode.
2. In the Receiver Mode RiCor TV:
▪ Navigate to RiCor TV Receiver.
▪ Press the A / V button to go to setup mode.
iVR sound.
▪ Set the desired sound level by pressing the buttons. V + / V- .
The maximum sound level corresponds to the sound level installed in the TV control mode.
3. Turn on / off sound
To turn on / off, the button is the button:

SELECT SOUND LANGUAGE

If the transmission supports multilingual with a BEAUTY, the user can select a three-key audio track by pressing the remote control button LANGUAGE.

Reading Announcements Gear

Button A / A. Opens a window with an announcement for the transmission viewed on full screenas well as in Program program, in PC, in Archive, in screens Now on the air and Today on the air.

PANEL

▪ Opens / closes the information panel (Time SHIFT / pause mode is off),
▪ Opens / closes the transfer viewing panel,
▪ Opens / closes the browser panel when watching Internet pages,
▪ B. PC, IPP and B. Archive Spreads / shifts the selected field with the name of the transmission to provide more complete transmission information.

OUTPUT

Button OUTPUT Performs the following actions:
▪ Returns the previous screen,
▪ Closes pop-ups context menusmessages without performing any commands.

MENU

Button MENU Opens \\ closes the main menu of access to the services and functions of the video recorder. To open the screen of the required video recorder service, select the Navigation Arrow on the menu and click OK For confirmation of choice.

Navigation shooters console

The ▲ / ▼ buttons serve for:
▪ Displacement of the "backlight" cursor on the active list of items,
▪ Move the cursor up / down by the list of channels,
▪ Text scrolling (reading announcements, Internet pages, etc.).
◄ / buttons serve for:
▪ moving the "backlight" cursor between interactive screen objects,
▪ Displaying the information panel in TV viewing mode on the full screen.
Button OK Serves:
▪ To execute the command of the selected (active) interactive object (buttons, menu item, list item),

Button Advisor calls an adviser on the screen, which provides fast visual assistance in the open application. Choose in the offered list the right question and click OK.

IPP

The IPP button opens the interactive prog of the transmission (IPP), where the user
can:
▪ View program gear,
▪ Go to the current transmission on the selected channel,
▪ Read the announcements of the program,
▪ Schedule a single transmission entry, a recording of one or all releases of periodic transmission, one or all cycle or series transmissions,
▪ Schedule reminders of the beginning of the gear,
▪ Carry out the words or genres.

Note
If you need to restart the IPP, press the PLAB panel button.

ARCHIVE

Button ARCHIVE Opens the Archive of Records, Archive. VideosFor all users of the video recorder.
This archive also acts as a list of scheduled records, ScheduledCo.
you can open by pressing the red button of the console.
Records can be played, block from accidental deletion, delete, sort, alphabet and rating, and search for gears.

Personal canal

The PC button performs the following actions:
▪ Opens a personal channel (PC) of the user.
▪ For the viewer chosen in the list, switches the modes:
“Form PC / Stop PC Formation”,
▪ On the PC screen (p. 43) opens a list Spectators.

R button ("Record")

The R button opens dialog boxes with different commands, depending on the MOS from installed mode View TV (p. 34-36).
▪ Modes "Use the rewind when watching" and Pause Disabled.
When pressing the button R. A dialog box opens with a request for confirmation of the start of recording. To confirm the recording of the current transmission, press the R or OK remote button.
For reference to write, press the remote control button. OUTPUT.
▪ mode " use rewind"Or mode Pause included.
Button R. Opens the dialog box, using the buttons you can perform
the following actions:
1. "Record the current transmission" is a record of the transmission of the "current" ether, starting with
pressing the button R..
2. "Save from the beginning of the transmission" - it is saved in Archive current transmission
fully.
3. "Write a fragment" - from the current or transmission of the viewed
channel.

Recording Playback Control Buttons

Buttons of the console (drawing on the right), serve to use the reproduction of the transfer recording in mode Pause, in "use a rewind" mode when viewing "(Time SHIFT mode), to control recording playback in Archive, Personal Channel. The description of the buttons is given in the chapter " Playback of transmissions”.

Colored buttons remote

Colored buttons perform different commands depending on the screen open at the moment, dialog box, panels.

"Fast" personal buttons

Colored buttons: green, yellow, blue - are personal buttons for the dawn of the user. Serve to quickly switch to a new viewer with
automatic installation of its profile.

Red button console

▪ Transition from viewing the transfer in full screen (if the transfer does not contain
the attractive application) in the screen is now on the air.
▪ In a personal channel (PC), opens the PC settings screen (p. 48).
▪ The archive opens a list of scheduled records (p. 68).
▪ When watching an interactive transmission opens an interactive application on the screen. Interactive gears are marked with a special icon :.
▪ Includes listening to short messages (news, announcements of gear, jokes, jokes, etc.) that are prepared " Service service personal messages”
(THX). The ATP Banner disappears from the Che Ch screen for a few seconds, but it can be closed immediately by pressing the blue remote control button.

Programming console

The console designed to control the video recorder can be learned to control the TV connected to the video recorder. The programming process (learning) of the console is carried out by direct copying of the TV control commands in the memory of the remote control from the video recorder.
The two consoles are put nearby so that the IR - the emitter of the training TV console is directed to the IR emitter of the student console and was at a distance of 2-5 cm from it. The first remote sends the command code of the command by the button down, the second takes it to its sensor. Note that the remote control from the video recorder has two IVR and TV mode, which are used to switch the modes, therefore they cannot be sent control codes and it is impossible to program.
To program the remote control, follow these steps:
1. To enter the learning mode, press and hold the TV button until it turns out and the indicator * Log in to the learning mode will not constantly burn:
2. After that, on the trainee, press one of the trained buttons (except IVR and TV). The indicator flashes in anticipation of the IR signal from the educational console.
3. Press the button on the TV Remote Tutorial. Termination of the flashing indicator on the trained console means successfully learning the button. Otherwise, learning did not happen.
4. Repeat steps 2-3 to train other buttons.
5. To confirm the end of the learning mode, press the TV button on the trainee and wait 30 seconds without performing any commands.

Note
In the process of learning the remote control, change the IR code of the already programmed button cannot be. To cross the button, it is necessary to start the procedure for learning again and reassign the IR code of this button.

Check the functioning of trained buttons

Check the functioning of the trained buttons.
1. Press the TV button, the indicator flashes once.
2. Press one of the trained buttons. If the button is trained correctly, the console will send Ik-
the signal and the button command will be executed.

________
* If the remote indicator does not burn, then check the suitability of the power batteries.
If the batteries are suitable, but the indicator does not burn, follow these steps:
▪ Remove the power batteries,
▪ Press 5 times any remote button,
▪ Insert the power batteries.

Screen keyboard

The on-screen keyboard is used to enter data into different fields, for example, to enter data when registering a new video recorder user, to enter the Internet address, to enter keywords to search for gears in an interactive program program, etc.
Consider using the keyboard on the input example keywords To search for transmission in an interactive program program.
▪ Highlight the data entry field using the remote navigation shooter.
▪ Press the CLAB panel button to open the on-screen keyboard.
▪ Highlight the letter by pressing the pressure arrow ◄, ▲ ▼.
▪ To confirm the selection of the letter, click OK.
▪ Enter the data fully.
▪ To confirm the end of the dataset, click the keyboard button Ready

Purpose of keyboard buttons

• Space Inserts gaps between words.
• Removal Removes the symbol before the cursor.
• Signs, Figures opens the keyboard with punctuation marks, symbols, numbers
• A / A. Switches lowercase / title letters.
• ENG / RUS. Switching keyboard layouts: Latin / Cyrillic.
• Ready Confirmation of the end of data entry.
• ARCHIVE Archive, video school
• IPP Interactive program program
• PC Personal canal

Main menu of the video recorder

Map of the main menu

Access to the services and functions of the video recorder is both sought through the main menu.
To open the menu, press the remote control button. MENU.
To close the menu without selecting the application, press the menu or output button.
At the bottom of the menu, the version of the software version loaded into the video recorder is specified.

How to open the application?

▪ Highlight the desired menu item with the remote navigation shooter.
▪ Click OK to confirm the selection.

Note
A number of functions of the video recorder can be opened with the "hot" remote control buttons.

Restore the system partition receiver Riort TV

In the case when software ( software) Improperly functions or not loaded, you can restore the system partition on the hard disk. To do this, follow these steps.

1. Turn on the Riper TV satellite receiver.

2. When sunbathing any indicator on the front panel, press and hold any remote button (for example, OK), sending a remote to a satellite receiver Rikor TV.

3. After 10 seconds release the button.

4. Press the same button 3-4 times with intervals of 1 sec.

If the window "" for 2-3 minutes. has not opened, Turn off the satellite receiver Rikikov. Repeat steps 1- 4 .

If the window " Restore the system partition on the hard disk"Opened, follow these steps.

• ▪ To restore the system partition, press the remote control button.
• ▪ To restore the system partition without removing video records, press the remote button.
• ▪ Close the "Restore system partition on hard disk" dialog box (BOK was opened, but it is necessary to postpone the recovery process) by pressing any other button of the remote control.

The process of restoring the system time is accompanied by the necessary messages. Prior to the completion of the recovery process of the system time, do not disconnect the power of the satellite receiver Rikor TV!

After successfully restoring the satellite receiver, Riottomatically reloads.

Attention! After restoring the system partition, all user data (questionnaire, archive, PC) and RIKOR TV settings, as well as the configuration of the Internet connection and GPRS modem are removed. The version of the receiver firmware returns to the state at the time of purchase of the Riper TV receiver.

Beforethe system partition restores the following steps.

• ▪ Turn off the satellite receiver Ricor TV.
• ▪ Insert a Rickor SIM card into the GSM module slot (if it is not a ricorem card).
• ▪ Turn on the Riortic TV receiver and open the GPRS Connection Setup window.

Record code value in the code line.

Afterrecovery of the system time you need to perform the following steps.

• ▪ Update the firmware of the RIKOR TV receiver to the current version by selecting the Main menu item. Settings\u003e Update.
• ▪ Restore GPRS connection. To do this, open the GPRS Connection Settings window and enter a predetermined code value into the code string.