Religments iPhone 6 when you turn off the cable. Why the iPhone is rebooted after disconnecting from the computer

For iPhone and iPad, after upgrading to iOS 11 and iOS 12, the problem arose, often the appearance - constantly reboots on the apple. Several situations can be distinguished: iPhone hangs on an apple and blue screen; iPhone reboots on an apple and a red screen; iPhone hangs on the apple and reboots; iPhone does not turn on the apple and turns off; iPhone does not turn on the apple and reboots; It does not turn on the iPhone flashes apple, etc.

If you have clapped with one of the above, you can fix them in the future ways.

Why is Irhone X / 8/7 / SE / 6S / 6 / 5S / 5 hanging on the apple and turns off?

Everyone knows, iPhone X / 8/7 / SE / 6S / 6/5 / 5S often arises problems. Especially, when updating the firmware, may not start, but show the apple, then either with one strip. What causes it? Maybe the firmware is not compatible with your device. Or the problem is that the malfunction is caused by system failures.

What to do if an apple is burning on iPhone but does not turn on

Do not worry, now we offer 2 ways to get out of reboot on the apple: enter an iPhone in DFU mode, or in service center, most effective method - Program.

The usual way to solve a problem with rebooting on an apple - DFU mode

We can recover the gadget when iTunes does not recognize your device. But these methods all the data will be erased.

For iPhone 6S, SE and below, please do it:

1. The first convey the device to the computer, turn on iTunes.

2. Cleash the home and power button at the same time, keep 12 seconds, after which we release the power button, but continue to keep the button home before defining the iPhone in iTunes.

For iPhone 7 and iPhone 7 Plus, please do it:

2. At the same time, press and hold the side button and decrease the volume.

3. After 8 seconds, release the side button by continuing to hold the volume button. If the Apple logo appears, the side button has held too long.

4. B. dFU mode There are no identification signs on the screen, the screen is completely black, iTunes will report that the device is in recovery mode. If the device displays the screen in which the device is connected to iTunes, repeat these steps.

For iPhone 8, iPhone 8 Plus and iPhone X, please do it:

1. Connect the device to the computer.

2. Tap and quickly release the volume button.

3. Tap and quickly release the volume reduction button.

4. Press and hold the side button until the screen becomes black, then press and hold the side button and decrease the volume.

5. After 5 seconds, release the side button, continuing to hold the volume button. If the Apple logo appears, the side button has held too long.

6. In the DFU mode, there are no identification characters on the screen, the screen is completely black, iTunes will report that the device is in recovery mode. If the device displays the screen in which the device is connected to iTunes, repeat these steps.

If this method cannot solve the problem, try using Tenorshare Reiboot.

Efficient and fast way to solve a problem with rebooting on an apple - Tenorshare Reiboot

Click the button and download the program for free from the official site. Set the utility to your computer (there is support for Mac and Windows).

1. Before restoring, it is unable to enter the phone to the recovery mode to see the device. Press and hold the home and power button at the same time, and then release the buttons until the connection to iTunes appears on the screen. Connect your iPhone to a computer using USB cable. Then run the Tenorshare Reiboot program on the PC, it automatically recognizes your device.

2. Click on the active button to "fix now". And select "Next", the firmware will boot.

Attention: Before working, users must make a backup. Theoretically, Tenorshare Reiboot does not bring data loss, but Tenorshare recommends backing up in advance to prevent accidents.

3. After downloading, click "Start Restore". The system recovery is executed, and then your phone will be rebooted. The device will be ready to work. And your problem will be solved.

If the solutions did not help, then contact the service center. After replacing the screen or battery, the device is restarted.

Tenorshare Reiboot provides all users of five opportunities to enter and exit the "Recovery Mode" for free. This will definitely eliminate some problems with them.

Such a review, using the Tenorshare Reiboot tool, you can solve not only this problem when the iPhone is hung in headphones mode, but others that may arise after iOS updates 11. For example, if your iPhone after installation new iOS. 11, or (during incoming challenge). There may also be a situation when the phone is. You can download the Tenorshare ReiBoot program for free on the official website of the developers.

Your iPhone is constantly rebooted, and you do not know what to do? We need our iPhone, and he must work all the time. It would be nice if there was one reason why the iPhone reboots again and again, but there is no one single reason for this problem. In this article, I will explain what causes the iPhone to continue to reboot, and show you how to solve the problem of rebooting the iPhone.

Attention! Owners iPhone. X: If you have an iPhone X with this problem, read my new article to find out how to stop the iPhone X from the reboot again and again. If these fixes do not work, go back and follow this manual.

Why does my iPhone continue to reboot?

IPhone, which constantly reboot usually divide into two categories:

1. iPhones that reboot periodically: you can use your iPhone for some time without any problems, and then your iPhone suddenly begins to reboot.

2. iPhone stuck in a reboot cycle: Your iPhone is constantly rebooted, and it is completely unsuitable for use. Apple logo, appears and disappears on the screen, again and again.

If your iPhone falls into the second category, go to step 5. It is impossible to make the first few steps if you can not use software On your iPhone. Let's decide this problem!

1. Backup iPhone

Before we start solving the problem of constant restarting the phone, then make sure you have a backup of your phone. If your iPhone has hardware problems, then all data from it can disappear. If we need, we will restore your iPhone later, and you will need a backup before recovery.

If you need help in reserve copying iPhonein the article apple support There is an excellent step-by-step guide.

2. Update iPhone Software (iOS)

Like Windows on PC or OS X on Mac, iOS is the operating system of your iPhone. IOS updates always contain many fixes program errors And other problems. Sometimes the software update eliminates the problem calling the iPhone reboot.

To check the availability of software updates, go to the Settings section -\u003e General -\u003e Software Update. If an update is available, install it. You can also connect the iPhone to the computer and use iTunes to update the iPhone software. If your iPhone is constantly rebooted, iTunes can help you best.

3. Determine whether any application is the cause of the iPhone reboot

It rarely happens that some application can cause a frequency reboot of your phone. For the most part, the programs on the iPhone are protected and should not cause any problems. At the same time B. App Store. more than 1.5 million applications, and not all of them are ideal and tested properly.

If you installed the application directly before restarting the iPhone, delete it and check if the problem is eliminated.

Settings -\u003e Privacy -\u003e Analysis -\u003e Data Analysis - Another place to verify problem applications. Quickly scroll through the list and look for any applications that are listed there several times. If you find such an application, then try to delete it and check if the problem was solved.

4. Reset all settings

Reset all settings is not a miraculous way, but it can solve some problems with software. Go to Settings -\u003e General -\u003e Reset -\u003e Reset all settings to restore factory settings iPhone. You will not lose your applications or data, but you will have to enter the Wi-Fi password.

5. Remove the SIM card

IPhones can get stuck in the reboot cycle, if there is a problem with connecting your iPhone to wireless network. SIM card connects iPhone to the operator wireless communication, Therefore, its extraction is the best way to eliminate this problem.

Do not worry: nothing will happen if you extract your SIM card. Your iPhone will be immediately connected to the operator as soon as you connect it back.

Apple's support service is written on how to extract the SIM card from the iPhone. There will be shown exactly where the SIM card is on the iPhone. Special clip is used to extract the SIM card tray from the iPhone.

If the removal of the SIM card eliminates your problem, return the SIM card to the iPhone. If the problem occurs after installing the SIM card, you need to restore the iPhone (step 7) or replace the SIM card.

If the SIM card extraction does not eliminate the problem, do not insert a SIM card back until you run the next step. If you want to know more about the SIM card of your iPhone, check out my article "Why doesn't my iPhone sees a SIM card?".

6. Full reset settings

Do not make a hardware reset on your iPhone, if it is absolutely necessary. It looks like shutdown desktop computerBy turning off it from the wall. This, as they say, is one of those cases when the hard reset is simply necessary.

To perform hardware reset, at the same time hold the power button and the "Home" button (pie button under the screen) while screen iPhone Apple logo will not turn off and will not appear.

On iPhone 7 or 7 Plus, the buttons required to perform hardware reset are slightly different. At the same time, press and hold the power button and the volume reduction button.

If you have an iPhone 8, 8 plus or x, the process full reset Also different. Press and release the volume button, then the volume button, then press and hold the side button.

No matter what you have model iPhone.Make sure you hold both buttons together at least 20 seconds. People were amazed when they came to the Apple Store, and I quickly corrected their dead iPhone using a hardware discharge. They thought they made this reset at home, but they did not hold both buttons long enough.

Fir you removed the SIM card with the iPhone at the previous step, now you can connect it back to the iPhone. We believe that you do not need to fully reboot the iPhone with a SIM card.

7. Restore iPhone. using iTunes.

The iPhone restore completely restarts the iPhone software (iOS) and this can eliminate many software problems. When we restore your iPhone, the likelihood that the software problem can lead to a reboot of your iPhone comes down to zero - that's why Apple Tech does it often.

Your iPhone must be connected to a computer to restore. I recommend making a special type of recovery that Apple Techs is called DFU Restore, which is stronger than normal recovery and can solve more problems with your phone. You will not find it anywhere on the Apple website - take my article to learn how to restore your iPhone in this way.

After the recovery is complete, you can re-download all personal information from the backup. copies iPhone In iTunes or Icloud. If your problem has not decided, then read further.

8. Hardware verification

Hardware problems are a common reason why the iPhone is stuck in a reboot cycle. If you use a phone case, remove it before continuing.

Carefully look at the charging port at the bottom of the iPhone. Check if any garbage is stuck inside, which can affect the phone number.

If you notice some rubbish inside the port, take toothbrushwhich you have never used, and carefully clean the charging port. Short circuit Or another problem inside the charging port can cause all sorts of problems with your iPhone.

9. Repair your phone.

We eliminated the possibility that due to problems with software, your iPhone will reboot, and we checked hardware problems on the outside of your iPhone. If your iPhone is still rebooted, your iPhone probably needs to be repaired.

If you want to get help at the local Apple Store store, make sure you have a meeting with an employee. A less expensive alternative is Puls, postal repair service, which can also help you with a solution to this problem. Read in our post.

Summarizing

When you read it, I hope we have corrected the problem that forced your phone to constantly reboot. I would hear your experience in the comments section below, and if you have any other questions, do not hesitate to ask them in the Payette Forward community. Read in our article.

Consider a rare, but very unpleasant situation when the iPhone restarts itself during standby mode or in active mode. Moreover, the device model is not important. At the very end of the article, we will tell how to cope with the situation.

How to find out because of which the iPhone itself reboots

IN recent versions operating system iOS Added the ability to register events. If you translate into familiar terms, then all events in the system are recorded. If your device begins to work unstable, you can use this log. With it, it is quite simple to calculate the problem area if the reason for the shutdown is a program failure.

The activation record of the function or application will always always go before recording an emergency disconnection. If there is no write record, then the reason for the shutdown lies in the hardware failure and you need to contact the service center, because Without the intervention of repair engineers can not do.

1. If the phone spontaneously turns off or during call iPhone. reboots, then the likelihood is that accumulator battery Loses contact with the device. Speaking easier, the battery moves away from contacts. This is due to the fact that with long-term use of the device there is a small backlash (gap between the connecting elements) of the battery lid.
   When talking or active use, the housing is excised, which causes the disconnection of the contacts. To check, take the phone and sharply shake it several times. If shutdown occurred, then the reason is detected.
2. If the root cause is not in this, then trace the statistics. Perhaps when you call, when you start a specific function or application or simply, when loading an iPhone is rebooted, then the most likely program failure.
   If the structure of the operating system arose failures or the application is not tested for full compatibility with the device, then when activated, sharp interruptions are possible in operation as a spontaneous disconnection or reboot. In order to avoid (and for solving) such problems, we recommend producing permanent updates Software products and use only certified applications.

As practice shows, if the firmware update or resetting the settings to the factory in the iPhone, it is possible to solve the problem with a reboot only with the help of qualified assistance to the wizard of the service center.

As you may have experienced, the iPhone can not always work as you expected. That is why the iPhone user can report problems on its device, for example, "iPhone hung screen", "iPhone does not turn on" and "iPhone X and iPhone 8 reboots", which is the main topic of this article. If you are worried about a frequent reboot of your iPhone 8, iPhone 8 Plus or iPhone X, read this article and find out how to cope with the IPhone X problem, iPhone 8 Plus and iPhone 8 reboots, how to fix it? Possible solutions below.

Tip 1: Forced reboot your iPhone 8, 8 Plus, X

If your iPhone X, iPhone 8 Plus and iPhone 8 reboots, the first simple, but effective solution you can try, it is forced to restart your iPhone, which is also useful when solving the problem " touch screen, does not work". The method of forced restart iPhone 8, iPhone 8 Plus or iPhone X differs from the method of rebooting the previous iPhone. Perform the following steps to find out how to do it.

Step 1 : Click and quickly release the zoom button volume .

Step 2. : Click and quickly release the button. volume Reduction .

Step 3. : Then press and hold side Turn on and off button ( Sleep / Wake) until Apple's logo appears.

If your iPhone 8, 8 Plus and X restarts every few minutes, try reset all the settings on your iPhone. On your iPhone in iOS, open " Settings » > « Main " > « Reset " > « Reset all settings ", To reset.

Check if your iPhone 8, iPhone 8 Plus or iPhone X restarts due to some old applications on your iPhone for the incompatibility of the application and the IOS operating system. In this case, you can delete this application from your iPhone or update these applications to the latest version.

If something is wrong with your battery iPhone.The problem with the "iPhone Reboot" can occur. If so, just replace old battery On the iPhone to a new one and see if the problem is not solved.

Find your iPhone 7 or iPhone 6, did they start rebooting after iOS update? Best way Solve the problem is the transition from iOS 11 on iOS 10. Although it is not easy to do, this is the most effective solution to the problem in a similar situation.

Tip 6: Restore your iPhone to factory settings.

If none of the above tips can solve the "iPhone X and iPhone 8" problem, you can try the last advice that is to restart the iPhone to the factory settings to set it up as a new one. When resetting all the data of your phone, including video, photos, music, before resetting.

Notes:

For iPhone users, such as you need to have a transfer tool iOS data and file management to help transmit and manage content iOS. Fully free softwarerecommended if Mobimover is installed on your PC under windows control 7 or later, you can export files from a computer to iPhone / iPad (in iOS 11 or newer), create backups content iPhone / iPad on a computer, synchronize data from one IDEVICE to another without any costs and limit.

Files that you can pass include photos, movies, TV shows, music videos, homemade videos, music, melodies, audiobooks, voice notes, contacts, messages, notes and more. Want to add ringtones to your iPhone X? Do not worry. Mobimover can help you with this. Want to synchronize contacts from your old iphone. on new? No problems. Use Mobimover to help you with this. Sounds great? Install Mobimover on your computer and try yourself.

And we decided to connect it to your computer. And at the time of connection you encounter such a problem: either shut down a blue screen (do not confuse with the "Blue Death Screen" (BSOD), with an error message, like "*** STOP: 0x0000007E (0xc0000005, 0x00000000000000005, 0x00000000000000005, 0x00000000000000005), Either the computer is simply spontaneously starting to reboot. The error occurs as a result of the incompatibility of the drivers, or when damaged.

In particular, such a problem is seen when connect iPhone To the computer on which Logitech webcam is installed. The conflict arises due to the incompatibility of the webcam driver with the iPhone driver (Specifies the Stop message: 0x0000007e). How is the problem solved? And the problem is solved in two ways.

Method 1

You need to simply update the webcam drivers. To do this, you should go to the site of Logitech. Look for the desired drivers by the name of your camera and just download them. After found necessary driverInstall it, restart the computer and try to connect your iPhone again. If suddenly the problem with an error and reboot will be repeated again, then the method 2 will help you.

Method 2

We find and delete all the drivers for the webcam. Here's how to do it:

1. Right-click on My Computer. In the drop-down menu, select the line "Properties". In the open window of "Properties" by clicking on the "Equipment" liner;
2. we see the inscription "Device Manager" and click on it. Next, among devices installed on the computer, looking for your webcam;
3. hover over the webcam the cursor and right-click;
4. in the menu that opens, select "Properties" and click on the "Properties" of the left mouse button;
5. a menu will open in which you select the "Driver" insert and delete this driver. To a request for confirmation of the removal press "yes";
6. now connect your i-phone to the computer again. The problem should no longer repeat.

And now how to solve the same problem, but on Windows Vista. So:

1. Right mouse click on "My Computer" and in the dropping window I choose "Properties";
2. click "Device Manager";
3. next - we reveal the branch with the name of the computer (display all devices);
4. we are looking for your webcam, we find it, click on it right mouse button and choose the line "Properties";
5. we find the "Driver" tab and click "Delete";
6. confirm the removal (click "Yes") and plug your iPhone again: everything should work!