How to disable the annoying notifications from the Realtek HD manager. No icon from Realtek HD dispatcher! How to enter the REALTEK control panel, and then I can't configure the sound Realtek HD writes a disabled connector

Good day!

Realtek HD is probably one of the most popular audio drivers that allows you to fine-tune the level and sound quality in Windows. To open its parameters - you need to start the RealTek Manager, the link to which must be either in the tray (next to the clock) or in the Windows OS.

But, recently (due to the fact that Windows 10 "puts" drivers independently) - References to the Realtek Sound Management Manager not! And however, may be "to blame" and failed versions of ...

Actually, below the sieve consistently, what and how to make the cherished link (label, icon) appeared ...

To help!

Volume icon does not react or disappeared at all ... what to do -

What if there is no REALTEK HD icon

"Manual" check

And so, if in the control panel and in the tray realtek dispatcher (And you remember that you installed it) - try entering the "C: \\" disk, and in the folder "Program Files" Find catalog "REALTEK" . If such a catalog is: Most likely, it should be the "RTKNGUI64.EXE" file - try to run it by clicking on it LKM (approx.: This is the dispatcher).

If the manager starts, and you can proceed to setting the sound - simply create a shortcut for this program (clicking on it PCM) so as not to look for it every time.

Removing the "old" version of the driver

Note: By the way, The latest version of the REALTEK 2.82 driver is failed. I have a PC when installing it does not appear icon on the sound control manager!

If the driver prompts to restart the PC - agree!

If you have a PC

Testing several versions of the driver from Realtek - it turned out that the "Files" of them is only one, the last 2.82 (and that, only on some machines!). Checking the somewhat older versions of audio drivers, it was possible to determine that 2.81 is a completely correct-working output. Links to them led below.

(Link to the official site). You can first try it if it does not work - remove the driver (see Step 1, 2 above), and install 2.81 Version.
⭐ ✔ (link to techspot.com). The correctly operating version of the audio driver. Recommend!

If you have a laptop

* In my case, there are several of them: what is interesting if you simply install the latest version of May 22 - then the link to the Sound Management Manager will not appear!
If you first install the very first release (weighs more than others), and then up to update it myself last version - That everything will work correctly!

❹

Installing a new version of the audio driver

Immediately, it does not represent anything difficult - it is enough to start the executable file and wait for the completion of the wizard. After, restart the PC / laptop.

Installing another version of Realtek HD 2.81

Speed \u200b\u200bSound Setup - Realtek HD

On the sim today everything ...

Good luck!

The vast majority of motherboards and laptops are equipped with audiockers from Realtek. They are able to give a good sound, and therefore most users do not buy external audio cards. However, the Realtek HD manager itself is quite crooked (although IE 6.0 is recommended to the official website, where IE 6.0 is recommended and the screen resolution in 800x600 is not surprising), in particular - it fills up a user with many notifications: about connecting the device, disabling, about the choice of gain etc.

Remove the connection / disable notifications / disabled devices is not difficult - it is enough to login in\u003e System\u003e Notifications and disable them from the Realtek HD Manager:

However, on most motherboards with Z-chipsets, REALTEK ALC1XXX (usually 1150 or 1220) are standing (usually 1150 or 1220), which support different levels of amplification: roughly speaking, the greater the level of amplification - the louder is your headphones. It is necessary so that the sound in the headphones with the impedance 200-300 ohms was not quiet. And here the problem is that each time the headphone is connected, the RealTek dispatcher is activated, it chooses the gain and tells you about it:

And okay, it would choose the gain right - but in my case it is also mistaken (the sound per 100% volume is still quiet), and at the same time the selected gain settings are saved only before turning off the headphones. The response of official technical support was simple: Okay, we work on it (yep, for half a year), so I decided to find a solution to this problem with notifications, and in general I could do it.

To begin with, install an audioer version 6.0.1.8339 (you can find out the version in the RealTek Manager itself) or higher. True, it is not on the official website of REALTEK, however, on the website of the manufacturer's motherboard, it should be. With older drivers it may not work, because it was in this driver who added saving custom settings Sound after rebooting (but, alas, not after reconnecting headphones).

After that, open the Realtek HD Manager, connect all the necessary audio devices (columns, headphones, microphones) to the necessary audio ports and configure them as you need (for example, I chose the "Extreme" gain profile, on MSI or Gigabyte motherboards, everything can look different):

Also uncheck in the RealTek settings a tick with "Connecting an automatic pop-up dialog for a connected device".

Now go to the Task Manager\u003e Startup and disconnect the Realtek HD Realtek Manager when starting the system (thereby you just disconnect the Realtek HD graphical interface, the driver itself will continue to work):

After that, reboot, wait for the system loading and connect the headphones - no notifications will appear anymore, and your strengthen level will continue.

However, this method has a minus - if you need to connect a new audio device, you still have to start the REALTEK HD manager again and configure it, and at the same time all your other audio devices. To do this, in the Task Manager on the Tabs tab, right-click on the Realtek HD Manager\u003e Open the location of the file, and in the Explorer window that opens, run the selected.exe:

The article describes the instruction, what to do if the Realtek HD Manager is not in the control panel. Realtek HD is free to distribute software that contains drivers to interpret sound streams. This package is a follower of a number of editors of the AC'97 firmware, which were created in 2004 by Intel. The hardware that controls HD Audio reproduces 192 kg2 / 24-quality two-channel output and 96 kHz / 24-bit in multi-channel mode. Total supported up to 8 channels simultaneously. When operating Realtek HD Audio, such a phenomenon is often encountered when the sound drivers work stably, without failures, and there is no sound manager in the control panels. In this case, we cannot configure sound scheme software method.

Search on computer audio manager Realtek HD

If you are going to edit a sound diagram or microphone, but there is no Realtek manager anywhere, no at the bottom in the tray, there is also no devices in the "Device Manager. No among installed programs - In this case, contact the "Control Panel", now click "Sound" - it should be displayed at this point. Check out additionally its presence in the Device Manager in the list of equipment, in the "Sound ... Devices" section.

Removing the old driver and installing new Realtek

If you can not find the sound manager Realtek in the control panel, try removing old driver On the sound equipment of your computer. For this:

Download Realtek HD Driver from the Official Site

If you searched all services and the corresponding panels, and Realtek HD is nowhere - you need to download it. To do this, open the boot page by http://www.realtek.com.tw/downloads/ and specify from 3 necessary for your system.

Before downloading from the RealTek site, you will need to register an account and log in to it.

The problem occurs sometimes due to the current driver, which was not taken from the official site. If the Windows where the problem occurs is also not official, but downloaded from the torrent or installed from the left "duals", in this case, you cannot REALTEK HD work window on your computer. Install the original manager of the dispatcher and restart OS.

What to do if the sound of headphones disappeared

Then run - "" on your system and check the audio tabs. Also open in the panel windows Applications And select "Sound" - Check the sound circuit, possibly the "Sound" checkbox is installed. Check also additional settings Sound.

It happens so when in Skype headphones start working after removing the tick " Automatic setting" Try to install, with the removal of the old, driver to sound.

You can download a special pack-pack, which has drivers for all occasions. Such a package is the "Driver Pack Solution". The advantage of such that this program itself scans your system and calculates old drivers and in the case of the outdated driver, downloads and installs new version Alone. Perhaps this particular package will help you detect and install the necessary version for a sound device with which problems arise.

Sound setting in headphones

Take a check over your system for viruses, using your antivirus software. In the event of various kinds of problems and errors in the system - it is necessary to check the entire hDD On viruses in a deep way of checking, because viruses are capable of calling any kind of errors and failures in the system, even if the Realtek HD manager is not in the control panel.

Many owners of built-in audio chips from Realtek, if in everyday work and do not use, at least they know that the so-called "Realtek HD Manager" is very often used to configure this equipment. What is this softwareFor which it is used, how to configure it properly and whether to keep on the computer, then it is proposed to understand. Special attention will be paid to some common problems associated with inoperability. installed drivers and appropriate software.

What is the REALTEK HD Manager for Windows?

For a start, a few words about the software itself. This package is created specifically for Realtek Soundcart built in motherboards Sound-On-Board and Discrete Chips with Sound Support high Qualitywhich explicitly indicates the corresponding reduction in the title (HD - HIGH DEFITING). However, it is naive to believe that the "Realtek HD Sound Manager" is just a certain software shell to manage playback settings and an improvement in the sound atmosphere using a plurality of additional effects. In fact, this package includes a complete set of drivers that ensure the correct operation of the sound system of the computer. By the way, it is these drivers that can be used for equipment from other manufacturers, but only subject to declared support and compatibility.

Main advantages

As for the main possibilities of such software, users basically give him a preference because it is implemented by support for some hidden opportunities Sanobard who are installed standard Drivers may be inaccessible to use. But as the main advantages most often called the following:

full support for all known sound formats without installing additional codecs;
high flowing frequency of sound;
complete support for bulk sound technologies computer Games based on SENSAURA technology;
improved speech recognition when recording or entering voice commands;
ability to work with all the self-adjusting devices of the Plug & Play standard.

If you pay attention to the last item, submitted in the list, it is easy to figure out that the Realtek HD Manager itself can be used not only to configure the equipment of this manufacturer, but also successfully use for other similar equipment without prejudice to the quality of sound and the occurrence of conflicts with devices. As a rule, this optional module is often installed directly during the installation of the drivers, but only if it uses "native" distributions, and not Windows database.

Where to find "Realtek HD Manager"?

As a control system element, this applet is usually represented in the appropriate section "Control Panels", and sometimes (after installation) can be activated in the autoloading section of the system and complement the system tray with its own module that works in the background.

But it happens that the "Realtek HD Manager" in the "Control Panel" is not. Do not hurry to blame in everything installed system or software. It is possible that you downloaded not the same distribution, or the installation was made with errors.

What if it is missing on the computer?

If the "REALTEK HD Manager" in the "Control Panel" no, it may very much that it is simply not installed in the system. The fact is that when installing "non-rigging" drivers, this situation is one of the most common.

In this case, it is recommended to go to the official resource of the developer and in the download section from the list select a software module with codecs (High Definition Audio. Codecs), save the hard disk installer, and then make an independent installation of this software.

How to establish this software?

Installation usually does not cause problems even at the most unprepared user.

The main thing is to pay attention to the launch of the installer solely with the rights and on behalf of the administrator, and upon completion of the installation, it is recommended to produce a recommended immediate reboot. If, after this, "Realtek HD Manager" is not possible in the system, the installation should be repeated by downloading additional packages. By the way, it is possible to identify that the driver (although working) is installed, you can in the Device Manager, where the Digital Signature and the Supplier name will correspond to the Microsoft Corporation.

In addition, when the distribution is loaded, separately note that in the description of some download links may be attended by something like "Drivers ONLY". This means that you only download drivers without the dispatcher itself.

Right on the download page in the present table at the bottom of the bottom find an additional stand-up applet with 3D SOUNDRACK effects.

However, even after that, there is no corresponding point, or it is, but "Realtek HD Manager" does not start or not visible in the system tray, it is possible that its display is simply disabled.

In this case, some experts advise to proceed to edit the registry (REGEDIT), in the HKCU branch via the Software section, find the RTKNGUI64 directory with the General folder invested, and on the right to change the show value of the Showtrayicon key from scratch per unit, after which the system is rebooted.

Sometimes on Windows 7 and higher after updating the drivers present in the R2.82 package, helps manual start The RAVCPL64.exe file from the HDA folder in the Audio directory, which is directly in the Realtek directory of software files. When the Realtek HD Manager appears, under the "OK" button, you need to press the icon marked by the letter "I", after which it is possible to select the display of the applet in the tray icons. Reboot is usually not required, but just in case it is better to perform it.

If, after that, "Realtek HD Manager" does not start, most likely, you will need to turn off automatic installation Drivers (which is most often required for Windows 10), and then repeat the installation of "native" drivers. Also, the problem may be trite for the fact that an unsupported sound card of another manufacturer is installed on a computer or on a laptop.

Basic parameters and sound settings

Now let's look at how to configure the "Realtek HD Manager". Basically, the parameters relate to effects and the environment.

It is important to pay attention to the configuration of the speakers, as well as to take into account the amendments to the type of room in which it is better to choose a room, exhausted felt (the sound will be softer). Effects, in principle, can be attributed to the standard type, but you can use a variety of pre-installed patterns. Separately, it is worth staying on the quality and sound format. It is better to choose a depth of 24 bits and sampling frequency of 48,000 Hz. Immediately you can configure the parameters related to the microphone.

Additional information and opportunities

As additional features Manager It is worth noting that with it, you can get information on the type installed sound card And its drivers used by the audio controller and the version of the DirectX platform. In addition, you can use digital, and analog inputs or audio outputs for which the basic parameters are installed automatically or using custom settings.

Questions of installation of additional codecs

Finally, if we talk about codecs, usually, it is not necessary to install anything additionally to install any audio or video when playing any format.

Although, if there is a desire, just in case you can use the universal K-Lite package, and among the versions to choose a mega package (Mega Codec Pack), which contains the maximum possible number of codecs and decoders.

RESULTS

If you take a summary, it can be noted that the drivers and the dispatcher itself will use all the users who do not imagine listening to music or watching a video without crystal clear sound. Settings are quite simple. However, if similar parameters can be set to the means of the system itself, the need for the dispatcher itself, by and large, disappears, since such options are identical (for example, they are all present in Windows 10). But for the convenience of control, the main program will fit very well, even, according to some users, despite several overloaded graphical interface.

In the event of problems with the launch, the methods for their elimination usually help. If the dispatcher for any reason does not want to work, it may well be that the installed sound card is simply not supported. In this case, it is no longer possible to re-install or edit the register of meaning - it still will not give it due.