Headphones are not turned off on the iPhone. Headphone mode is not turned off in iPhone

the iPhone 6 displays the icon speaking in the status bar, the headphones allegedly connected to it and does not make any sounds. But in fact, no headphones are connected. Not a cable or Bluetooth. I can not understand how to solve such a problem. I turned on and off the smartphone, but it does not help!

Decision: Reboot really quite often solves such problems and we always recommend trying this method in the first place.

Disconnect Wi-Fi.
Restart your smartphone.
This method helps most of users.

If this does not give results, the next step is worth trying to clean the headphone jack using a conventional toothpick. If dirt or garbage is present inside, it may be the cause of such a behavior of the iPhone. Also for cleaning the port you can use compressed air.

Try to connect and immediately turn off the wired headphones. Repeat this action several times in a row and again check whether the problem persists.

Before making further actions:

Make sure your computer has the most fresh version iTunes programs. If necessary, make an update.
For iTunes help Make full backup Your iPhone. Transfer all necessary information In the computer, since with further actions it will be removed from the memory of the smartphone.
If you are installed on your iPhone iOS 6 or newer, open the settings\u003e ICloud and deactivate the Find Iphone item.

To return the device to the initial settings, do the following alternately:

Connect your device to the PC with the original USB cable.
In the iTunes program, find and open the management tab of your iPhone, iPad or iPod.
On the General page, click the Restore button.
When you appear a window with a warning about deleting user data, confirm that you want to restore the device. After that, iTunes will start downloading the latest software version for your device and upon completion, reset the settings to the factory state.
After the recovery is carried out, the device will restart and you will see the welcome screen of the setup assistant. Go through all the steps to configure and activate your device. At one of the steps you will be selected - configure the device as a new or restore from the backup. If you do all these procedures from the iPhone, make sure that it has an active SIM card. It will be needed to complete the activation procedure.

Tell us in the comments if this method was useful to you to solve problems with sound. If you are experiencing such problems, describe them in the comments. We will try to find a solution and tell you in detail about it in the following articles.

If the headphone mode is not turned off in the iPhone, this indicates its malfunction. It happens that the phone does not work in the phone, complicating the process of talking and listening to music through headphones.

In order to restore the sound functions in the iPhone, you need to determine the reasons due to which the phone is hung in headphones mode. Most often such situations occur due to the damage to the mechanical nature or the connector blocks. As practice shows, an independent solution to the problem is possible when the headphone mode is turned on in iPhone.

Why not turn off headphones on iPhone?

If the headphone mode is not turned off in the iPhone or sounded sound, you need to check the integrity of the socket. It happens that dust, sand, garbage particles, etc. came to the connector, etc. In addition, it is impossible to turn off headphone mode for such reasons:

failures in work operating system (does not recognize when the headphones are turned on and does not turn off the mode)
mechanical impacts (if the slot is deformed as a result of the fall, then the sound can be lost, and the phone will be constantly in headphones mode)
contact with liquids (if moisture falls into the connector, then you will not be able to disconnect the headphone mode or the phone can turn off completely)

Signs of sound impairment on iPhone

Sound quality is one of the many advantages of modern devices. But there are cases when hearing is lost and speaker does not work in headphones mode. On violation of the work of the smartphone are evidenced by such signs:

not audible interlocutor when talking
no silent mode
earphone mode included in iPhone
sound disappeared
headset does not work
headphone mode does not turn off
volume is not added

Some of these problems you can try to eliminate yourself. If a internal components The iPhone was not injured and the headphones work, it means that there is a chance that the inclusion and shutdown will help if the phone is dependent.

Ways to restore your device

Apple technique is constantly being improved and upgraded, the IPhone breakdowns happen not so often. If the headphone mode is turned on in iPhone, which is not turned off with the usual way, follow these steps:

clean the toothpick connector
pull the nest from dust
restart the device with headphones included
turn on the speaker mode
adjust the volume
disable Wi-Fi

Try turning off the headphones function to switch to speaker mode. If the phone is hindering and does not respond to commands, overload it. If the headphone does not turn off the function, you may need to repair the iPhone.

Qualified repair

If your iPhone shows connected headphones, at the moment when they are disabled, the phone constantly hangs, and the sound functions disappear, consult professional craftsters. They will recover iPhone in a short time.

The hanging of the headphone regime is a fairly common problem, with which they often turn to those skilled in the art. Despite the fact that only original headphones are used in the iPhone, problems also arise with them.

After the fall, the "headphones" mode may be engaged and not to switch to the speaker, in this case, the specialists will determine the connector in a short time, restart the iPhone and eliminate software failures.

Why it is worth contacting the SPEU specialists

Many experienced masters who offer favorable terms of cooperation on Yudu. Experts have everything required tools for

Is your device stuck in headphone mode and reproduces it, only after connecting the headset? In this article, we have collected all the ways to turn off the headphone mode on iPhone 5, 6, 7, 8, X, SE, these methods are also suitable for Apad and Eupoda.

For the start, go to "Settings", "Sounds", and then "Ringtone". Try to include different call melodies and look if your speakers work.

Make sure your battery is charged more than 30%. Perhaps the problem is linked to the insufficient power level.

Finally, close all your open applications, double-clicking "home" and expand them to close each separately. Then restart the iPhone.

Try connecting a Bluetooth headphone

Try connecting the device to the dynamics of Bluetooth or to Bluetooth headphonesAnd then disconnect it. Look, whether the headphone mode on the iPhone is turned off when headphones are disconnected!

When you connect the iPhone to the Bluetooth device, you can exit the "headphone regime". To do this, first turn on the Bluetooth ("Management Center" or using settings).

After connecting K. bluetooth dynamics Play song. During the playback of the song, disconnect the Bluetooth setting on the phone. This will correct the device error.

Check out some settings

The parameter called "Call Audio Routing" determines where the sound is heard during telephone and audiosiles.

So let's check the settings. Go to "Settings"\u003e "Main"\u003e "accessibility" and scroll down the page down to the "Interaction" section. Continue to scroll until you find a call. It should be on "automatically". If it is not, tap it and select "Automatically" from the list.

If the "automatically" mode is already selected, try installing it on Speaker. Now test it by making a call or audiosiles on FaceTime.If the speaker works, then go back to the same configuration and change it to "automatically".

Switching this setup mode can help disable headphone mode on iPhone and Apad.

Try turning on the flight mode

Switch to "Flight Mode". Go to "Settings"\u003e "Flight Mode" and turn it on. Wait 15 minutes or more, and then turn it off and check if your speakers work.

Turn off the headphones

If iPhone in headphone mode without connected headphones, then in the port of the headset can be trash, dirt. To remove them, disconnect, and then re-connect the headphones several times (at least 7-8 times). After that, restart your iPhone (pressing and holding the "Home" and "Nutrition" buttons.) On iPhone 7 and iPhone 8, x Reload you can

Some users reported that they corrected this problem using a hairdryer. You can also use toothpick or Q-Tip and clean the port to remove dirt residues. To use Q-Tip, make sure that you take off most of the cotton so that it fits tightly to the port, but at the same time not stuck in it. Using the Q-Tip inside the socket, do multiple speed to clean the port.

If you decide to use a hairdryer, make sure that it is in the "cold blowing" mode or at the minimum temperature.

Be sure to turn off the phone before taking any steps listed above.

Push the headphone jack

Before blowing the air into the nest for headphones iPhone., take a flashlight and see if there is anything inside. If you noticed something - pull it out. Now carefully and carefully blow the air right into the headphone socket. This should remove any small particles.

Try the sprayer. It is commonly used for cleaning computer keyboards And other electronics. Fortunately, a small plastic straw mount is perfect to the nest for headphones.

Check if your sound is returned to the operating mode.

Several of our readers even used a small vacuum cleaner to clean the headphone jack (and it worked). Just be very careful.

Use dry cleaning napkins

As already mentioned, this problem with the iPhone usually occurs when the headphone connector is damaged or the large garbage accumulation. Therefore, it is necessary to correctly clean the headphone socket. Take cotton fabric and clean the hole several times. Make sure that when cleaning the connector you will not apply water on it.

Some users believe that toothbrush It helps to clean the nest of headphones from dirt and dust. It is necessary to clean with a light touch, you can add a little alcohol (add water and vodka it is impossible). Make sure your phone is turned off before inserting any tool into the headphone socket.

Another way is to make your own cleaning brush using paper clips and transparent ribbon. Bend the clips directly and wrap it with the tip of the sticky side of the tape out. Gently insert a sticky tip into the headphone socket, slightly pressing it on the side to pick up dust and dirt. Do not forget to turn off the phone before you start doing it.

What if the iPhone thinks he is in headphones?

What to do if an iPhone thinks what is he in headphones?

iPhone heard sound only in headphones (solution)

IPhone thinks he's headphones what to do

You can also fold a small piece of tape inside out the sticky part outward. Gently insert the ribbon into the port of the headphone connector and squeeze it on the side. Leave long tips so that they can be easily removed.

In addition, on the inside of the connector there is a small hole, in which dirt and dust often gets stuck. Try to clean it with a pin with a small amount of alcohol. It should help remove headphone mode on iPhone and Apad.

Check for water damage

Headphone socket is one of the most vulnerable iphone areas, and it may be damaged unconsciously. If you like to run or train while listening to your favorite tracks, there is a possibility that the sweat can get into the headphone socket.

Even if at that time he was in your pocket. To solve this problem, try to check your device, for water damage. You can always use silica gel dryers on your phone or other adsorbents.

Did the sound on the iPhone 6? Problem and solution!

Lost sound on the iPhone, what to do?

What if the iPhone disappeared the sound?

Did the sound on the iPhone? Problem and solution!

Sound on the iPhone 7 solution!

Try to include some music or other app

First connect headphones, open iTunes and play any song. Wait until screen iPhone automatically blocked. Then unlock it, close iTunes, double-clicking on it and turning up, disconnect the headphones. Open YouTube, Pandora, Spotify or another application and enable music.

Put the maximum volume and check whether the speakers work. If so, go to other applications and make sure that the sound also works.

This is one of those councils of experts who mainly work to correct the headphone regime on iPhone 6. To begin with play a song on the phone and allow your phone to be automatically blocked during playback.

Now connect the headphones to the device and open it. Manually stop playing the song and disconnect the headphones. This will allow your phone to get out of the "headphone regime".

Update to stable version iOS

There may also be a problem with your version of iOS.. Therefore, it is strongly recommended to update it. It will also solve any other problem with your device.
Open "Settings"\u003e "Basic"\u003e "Software Update" and "Download and Install" New iOS update On your device.

Reset all settings on your iPhone

Some users have enough reboot smartphone. If all of the above solutions have not worked, this method can help. Deletes all existing settings on your phone.

Simply select "Settings"\u003e Reset\u003e "Reset All Settings" and confirm your password. Your phone will reset the settings and restarts in as usual mode. Using the iPhone application, can you easily restore the firmware?

These methods helped you turn off headphone mode on iPhone? If not, try tips that are collected from different forums.

Users of users who encountered a problem

The user reports that the problem when the iPhone is stuck in headphones mode disappeared. After he finished backup ICloud, and it found that the problem of jams in headphones on the iPhone and Aipad disappeared. If you create backup Through iTunes, it can also work for this backup method.

Tips readers:

Call someone with headphones enabled and press the speaker. As soon as you hang up, turn on the iPhone on Silent, then turn off.
For iPhone 7 and other models without headphone jacks, try to connect charger Back to your iPhone, and then disconnect it. If necessary, repeat.
Use air by spraying it into the headphone socket or port, at the same time pressing both volume controls.
A simple solution - Enable the audio off button and press the volume buttons. Do not forget to turn off the sound off button.
Open apple application Voice Memos and write down a new voice. It can also solve the problem.
Try the FaceTime Call. Be patient because you will not hear the sound within 10-30 seconds, but stay on the call. The speaker will then turn on, and the phone will be released from the "headphone regime".

Phone 5 Sound works only in headphones

On your phone a headphone icon appeared? You are not alone, with such a "glitch" people face quite often. This is not only an unpleasant fact that shows a temporary malfunction of the system, but also the real reason for further "hanging" of the device. That is why mobile devices are trying to solve the problem faster.

Common causes of malfunction

One of the most famous and common causes is a blow. A failure may happen from him that affects the further work of the mobile apparatus.
Moisture. It can be a copied condensate from the temperature drop when the device gets from the frost into a warm room, as well as the liquid spilled onto the mobile.
Mechanical contamination of the jack of the connector, which appears in the process of its normal operation.
Inactive removal of the headset from the connector. It can "confuse" the phone and make it "think" that the headphones are still inside and are connected to it.

Important!If the problem lies in the fact that the device is spilled with liquid, then you should not try the following options below, but simply you need to attribute your device in service center.

If you want to try to solve the problem yourself, then you should immediately turn off the smartphone, disassemble it by driving the battery, and let it seek in a warm place for about a day. If this method has not worked, it means you should accurately pass the device to repair.

Diagnostics

Often the cause of the fault is quite obvious to the user, but there are several actions that can be performed to more accurately diagnose:

If the icon appeared due to an inaccurate extraction, the user may not immediately notice the problem. Nevertheless, he will be able to exclude other error options due to the fact that this is the only option in which the headphones were physically in the device at the time of its occurrence.
Moisture. If a small condensate has accumulated on the device itself, it is quite difficult to determine it. A sign of such a problem can serve as a conversion of frosty temperatures in a very warm room. Most devices at the same time normally carry such differences, but there are exceptions, whose fault is manifested through the headphone icon.
Pollution. It may not be obvious to the user. Moreover, when it is presented, the headset can be effectively used for its intended purpose, but if there is a similar problem, it is completely solved by simple manipulations.
Inactive extraction. "Symptoms" of this problem are similar to those that are in contamination. In both cases, the definition of the problem occurs during its solution.

How to remove a burning icon from a smartphone screen

There are several simple actions to solve the problem.

Important! If all actions were tested and there is no result - you need to contact the service center for repairing the device.

Reboot. This solves the problem in 80% of cases.
Visual inspection of the nest of the entrance. Even if the pollution is not detected, it is worth "blowing" this nest and try to gently "knock out" from it particles of dust. After that, it is also recommended a reboot.
Remove the battery and let dry. This option should be tried the last. If the device was not flooded, and there is a suspicion of the formation of condensate, it is enough to remove the battery and give it to succeed 3-4 hours.

As you can see, the reasons for failures can be a lot. The main thing is to find the reason why this happens and perform the correct connection.

It's no secret that modern phones This is not a gadget for calls, it is personal Computer. With the iPhone you can call, send messages, view the Internet, listen to music in headphones and a lot more. Software developers are trying to make our lives easier, simplifying the management of the iPhone, but at the same time adding new features to it, this situation is constantly balanced on the verge of the maximum possible functionality of the gadget and intuitiveness of management of complex functions. In order for a person to finally not confuse, many trivial actions are made automatically. For example, if you have connected headphones to an iPhone, it will automatically start playing the sound and calls to the headphones as soon as you turn off the headphones, the iPhone will understand this and again starts outputing music, alerts and calls to your own speaker.

All would be good, but in rare cases, such automation gives a failure and when the headphones are disconnected from the iPhone, it continues in headphones mode, and in this case you remain without sound. What to do? How to disconnect the headphone mode to the iPhone, if the headphones are already disabled?

Causes of abnormal disabling headphone mode in iPhone

In order to cope with the problem, you need to understand its cause and essence. If you for a long time Connected and turned off the headphones from an iPhone, which automatically recognized this, and in the past several times stopped disconnecting the headphone mode, it means that something went wrong: either happened software failureOr has a hardware error.

I lasted the entire Internet, both Russian-speaking and bourgeois and wrote down all the main reasons for which people did not disable headphones in the iPhone even after their disconnection:

Program crash at the moment when you turned off the headphones from the phone;
The iPhone processor was maximally loaded by some kind of background task and ignored the headphone shutdown;
Low quality headphones led to a violation of automatic shutdown of headphone mode;
Problems with a connector on iPhone;
Hit in the nest of foreign objects;
Entering the water supply;
High humidity indoors.

Methods to solve the problem of the impossibility of disconnecting the headphone regime in the iPhone

Above, I designated the main reasons for which you can stop working in iPhone automatic shutdown Headphone regimes. Now let's deal with how to solve each of the above problems. In 90% of cases, one of the solutions is triggered and you will not have to attract the phone to the service center. However, I want to warn that if the problem arose once she can repeat in the near future. If the problem starts to appear regularly and even if it is solved by one of the following proposed methods, I highly recommend attributing an iPhone to the service center for a radical correction of the problem. It's like health, if you started to hurt the back, then you should not hope for different ointments that are treated with symptoms, not a problem. To cure your back or find out the cause of the pain you need to refer to the doctor, just as appliances and iPhones.

Headphone mode does not turn off due to the iPhone software failure

If for some reason you have a reason to suspect exactly the phone's software in the fact that the headphone mode in the iPhone does not automatically turn off, you need to do the following:

Disable headphones and restart iPhone

If the reason was exactly in software, It is very high likely that after the usual reboot, everything will come to normal. If after rebooting the headphone mode still works, although the headphones themselves are disabled, the following operations should be done.

Connect the charger to iPhone and restart the phone again. Please note that the charger must be connected to the power grid.

If this manipulation did not help, and you are 100% confident that the reason for the failure has become software, you only have one solution.

Connect the charger to iPhone and make Hard Reset. . Return the phone to the factory mind. This means that all your data, contacts, SMS, and everything else will be removed from the phone, and it will become as it was when you first turned on after the purchase. Please note that this is the most radical method and resort to it. I advise only when you are 100% sure that the problem is in the software and only if none of other ways to disconnect the headphone regime helps.

Headphone mode in the iPhone is not turned off due to moisture from the phone

It often happens that moisture falls inside the iPhone, even a small number of it is enough to have a challenge with the phone. For example, you got under the rain, and you need to see the route, timetable traffic, or accept phone call. It would seem that you have made a phone from your pocket or bags for a few minutes, quickly made your affairs and removed it back, but one drop of water has managed to get into the audio part. This is enough to ensure that problems with headphone regimen in iPhone began at a certain coincidence.

So, you suspect that the headphones mode began to climb due to moisture from either an iPhone itself or in the audio part. There are several ways to solve this problem:

First of all, the phone must be dried. If you have the opportunity to use a vacuum cleaner or hairdryer - this the best decision. So, remove the nozzle from the vacuum cleaner or the hair dryer so that you have a naked tube. Turn on the vacuum cleaner and bring the iPhone audio dispenser to the pipe, push the phone a couple of minutes so that the air flow can evaporate the water inside the audio. After that, try to connect and turn off the headphones. If the reason was in water, then this method should help. If you have a hairdryer, you need to do the same, but with a small difference. Set the hair dryer to the cold air, you do not need to once again warm the phone with a hot air stream. Do not turn on the hairdryer to maximum power, it will not help. Turn on the hairdryer in the "cold air" mode at minimum power and start blowing in the audio in the course of one minute, after which try insert and get the headphones.
If there is no access to household appliances, it is possible to use dry rice. Watch the phone with a rag dry, open the bundle of dry rice and put the phone into it for several hours. Rice should absorb moisture, which is in the phone. It is not so effective method For several reasons: First, you will have to wait long, and secondly, rice does not very effectively absorb moisture and it is necessary to use it only if there is no other possibility. After the phone lay down for a few hours in a dry rice, get it up and try to connect and disable headphones, the headphone mode in the iPhone should turn off.

If you have a cook salt and a paper napkin, it is better to wrap the phone into a napkin and put it in salt. Remember that when using salt, the phone must be protected from direct contact with the salt using gauze, napkins or other material that will skip moisture, but will not allow direct contact of the iPhone with salt.

Headphone mode in the iPhone is not turned off due to mechanical contamination of the audio

If you suspect that the reason for not disconnecting the headphone regime in the phone can be a banal contamination of the audio, then it is easy to fix it.

Remember - cleaning contacts must be carried out carefully, carefully, they are rather fragile and easy to beast. It is not necessary to put it hard on them or curvature, light touches should be enough if the problem does not turn off the headphone mode in the iPhone really consists in contamination of contacts.

To remove dirt from contacts inside the audio, you will need an ordinary toothpick. Take the usual wooden toothpick and any bright flashlight. Will be lantern inside the audio disgrace so that you can see contacts inside. Carefully try to consider contamination from the contacts with the toothpick. It usually grabs several movements so that the contacts have a normal operation. If this does not help go to the next step.
You will need toothpick or match, piece of wool and alcohol. Slightly moisten the wool in alcohol and turn it on the match or toothpick. Now this cotton try to clean the contacts within the audio part. Of course, cotton wool should be a bit so that the toothpick can perform progressive movements inside the audio. It should not be poured by the alcohol connector, it is only enough small droplets applied to cotton.