WINDOVS is not installed in a new hard drive. What measures need to be taken to install Windows

What errors did not have to hear and see when installing Windows OS (and I started to do it since Windows 98). Immediately I want to say that most often, to blame software errors, I personally would give them percentage of 90 ...

In this article, I would like to dwell on several such program cases, because of which Windows 7 is not installed.

Case number 1

This case happened to me by himself. In 2010, I decided that it was enough, it's time to change Windows XP on Windows 7. I myself was an opponent and Vista and 7-ki at first, but I had to move all the same because of the problems with the drivers (manufacturers of new equipment simply stopped producing drivers for more Old OS) ...

Because CD-Rom'a at that time I did not have (by the way, I do not even remember why) the choice of how to install, naturally fell on the USB flash drive. By the way, the computer then worked for me under windows control XP.

I purchased in a general disk with Windows 7, made an image from him from him, ... Next, I decided to start the installation, reboot the computer ,. And here I come across the problem - the flash drive is not visible, it happens just download windows XP S. hard disk. As soon as I did not change the BIOS settings, I discharged them, changed the priorities of downloads, etc. - all in vain ...

Do you know what was the problem? In the fact that the flash drive was not recorded. Now I do not remember what utility I recorded that flash drive (probably it was all the case in it), but helped me correct this misunderstanding program Ultraiso (about how to record a USB flash drive in it). After overwriting a flash drive - installing Windows 7 passed like oil ...

Case number 2.

I have one friend, it disassembles well in computers. As it asked to go and prompt at least something, why it may not be installed OS: an error occurred, more precisely, the computer simply depended, and every time at different times. Those. It could happen at the beginning of the installation, and could be 5-10 minutes. Later ...

I went, checked first BIOS - it seems to be properly configured. Next began to check the flash drive with the system - there were no complaints to it, even for the experiment I tried to install the system to adjacent PCs - everything fell without problems.

The solution came spontaneously - try to insert a USB flash drive to another USB connector. In general, from the front panel system Block I rearrange the flash drive to the back - and what would you think? The system after 20 minutes was installed.

Next, for the experiment, I inserted a USB flash drive in the front panel and began to copy a large file to it - an error occurred in a couple of minutes. The problem was in USB - I do not know exactly what (perhaps hardware is something). The main thing is that the system was installed and I was released. 😛

Case number 3.

When installing Windows 7 on the sister's computer, a strange situation was happening: the computer immediately fooled. Why? Unclear…

The most interesting thing is that in the usual mode (OS has already been installed on it) everything worked normally and no problems were observed. I tried different distributions of the OS - did not help.

The case was in the BIOS settings, or rather in the drive for floppy drive floppy. I agree that most of it is not, but in the BIOS then the setting can be and it is the most interesting, turned on!

After turning off the floppy drive - the hangs stopped and the system was safely established ...

(If it is interesting, in this article in more detail. The only thing she is a little old ...)

Other common reasons for which Windows 7 does not install:

1) Incorrect recording of a CD / DVD or flash drive disk. Be sure to check! ()

2) if the system is installed from the flash drive, be sure to use uSB ports 2.0 (installation of Windows 7 with USB 3.0 will fail). By the way, in this case, most likely, you will see a mistake that was not found required driver Drive (screenshot below). If you see such an error - simply stop the USB flash drive in USB 2.0 (USB 3.0 - marked in blue) and start the installation of Windows.

4) Before installing the OS, I recommend turning off the printers, televisions, etc. from the system unit, to leave only the monitor, mouse and keyboard. It is necessary in order to reduce the risk of all kinds of errors and incorrectly specific equipment. For example, if you have an additional monitor or TV to HDMI - when installing the OS, it may incorrectly set (I apologize for the tautology) the default monitor and you will disappear from the screen!

5) If the system is still not installed, perhaps you do not have a software problem, and the hardware? In the framework of one article, it is not possible to consider everything, I recommend contacting service center or to good friends who understand computers.

All the best…

Good day My dear readers!

I recently decided to put the operating system from scratch and faced a problem that led me to confusion. Like that installation of windows 7 requires a driver.

First actions

If you encounter such a problem, do not despair, I will tell you what to do. To begin with, I will explain why this could happen. Almost all users use distributions that downloaded from the network and independently recorded on the USB flash drive or disk. Nobody gives warranty that downloading files has passed without incident. Maybe some part did not stop, and now Windows asks the driver for an optical drive. Plus, it is possible that the disk image itself was broken or infected with the virus (check the image on viruses can be the same Comodo Internet Security). You can't know this right?

The first thing to be done is to find another image with a distribution and write it once again to a replaceable carrier. It is also important to be sure that your storage device is completely proper. Otherwise, it is possible to give not one hour. Try to change the USB port when the flash drive is connected. Maybe he loosened and began to climb.

If it does not help, go to the next step.

Errors because of the components

While trying to install an operating system from other distributions, pay attention, the driver drivers require your computer. For example, if the system needs software for a hard disk, each time, it is quite possible that the problem is in the BIOS or in the hard drive connector.

If the OS when installing requires a drive driver, it is quite possible that the bios settings also moved. It happens that with careless circulation, the SATA cable that feeds the components from motherboard. Because of this, the BIOS settings are knocked down, then requires their adjustment.

In order to enter its settings, it is necessary immediately after restarting the laptop to clamp one or more keys. Depending on the laptop model, the desired buttons vary. I will give a sign that helps you find these keys.

If everything is done correctly, then such a sign will appear.

Further, in the hard disk section, find your device and change its priority to disable or none. Winchesters are two types - SATA and IDE. If you do not know which one is your model, then check both tabs with HDD in BIOS. Reboot and make back changes. Then again restart the PC and try installing the system again. If the PC again requires the driver for the hard disk, then the problem is hardware.

The same applies to your drive. Only in the bios you turn off no longer hard drive, but the drive.

Solving hardware problems

If everything that is described above does not help, you will have to disassemble your car. By and large, there are no problems with this on laptops. Turned over, promoted, gathered. But I will describe everything in stages.

Initially, you turn off the PC, pull out the feed cable and take out the battery. Be sure! Otherwise, you can burn all components, as the power element has a charge, and it can lead to short closure! You need to solve the problem with the drivers, and not buy a new computer.

Then, you need to unscrew all the bolts, but do not lose them. Remove the panel and part of the housing. Before you will appear almost the same picture, as in the image below.

Self hDD Located here.

You need to turn off and connect again, but first remove the mounts, otherwise they will prevent it. Just move it to the side, pull out, just in case, blow the contacts. It will be better if you wipe them with an ordinary handle eraser. Then attach the device back. Also put the mount. Just in case you can watch the video on the network, how it is done

If the system required the drivers for a drive, then you need to shoot your drive, respectively. Then you collect everything, restart the PC and try to set the system again.

If everything went well, the system was established without errors, then the first thing to do is put the drivers on the Wi-Fi. You will need to enter the network and download the program to diagnose your hard drive. For example, HDD REGENERATOR for Windows. Download you can here. Install the software and run full check. The program itself will tell you what you do and in what state your device.

If all the indicators are normal, then you need to update the drivers to the HDD itself. Where to download them? Lusha is only on the manufacturer's website. If it is difficult, use the utility Driver Booster. FREE. Download you can from here. Run the scan, and it will make all the necessary actions. It will only be left to restart the laptop. Thus, the problem with the driver error is solved on the root.

Always carefully treat your laptop. Do not drop, do not beat on it, especially in the area of \u200b\u200bthe hard disk. This is a fragile component that is easy to damage. In it, the reading head is at a distance of a hair thickness from magnetic dies. If the scratch appears on them, you will have to buy a new device!

Conclusion

I brought you all the methods that will help solve the problem with a mistake of this kind. In most cases, it arises precisely because of the previously broken file image file or when the downloader program errors. It is not observed with licensed discs of operating systems. It can often be found in assembly distributions. Such I do not recommend that you install.

Homegrown programmers can watch anything all anywhere, and you will have to suffer. Read user comments before download. If the battered distribution, you will write those who have already tried it.

On this I say goodbye to you, my dear readers. Share a link to an article with your friends in social networks And subscribe to blog updates! I wish you not to meet problems with your computers! To new meetings in my articles!

It often happens that for acquaintance with the new OS, the user does not run to the store for a new computer or laptop, and puts new version On your tested computer time. And this is quite acceptable, since in recent years, Microsoft, in this regard, has gone to significant concessions to its own users. For example, the same device that could provide a comfortable work of Vista, you can easily install even Windows 8.

Here you insert the installation disk into the drive, the system began to install ... Stop! And what to do if if 7 requires a driver? Unfortunately, this problem is not so rarely found, and therefore it is necessary to talk about the methods of its decision.

First, we will discuss the reasons for which the OS still at the installation stage can begin to "be". First of all, you could write to the disk initially "broken" image of the system. Where did you get it from? If from some "left" site, then it is better to look for a source more repetitive. For example, the official image of the system. But even if you are using the official installation disk purchased for your money, and when installing Windows 7 requires a driver, the reason should be sought in something else.

On old PCs or laptops that still remember the times of "forever living" XP, BIOS can simply not perceive the new OS. If you just have the case, it will not hurt to go to the site of the manufacturer of your motherboard and download last version firmware.

If it is not, then everything becomes even more difficult. In this case, you will have to contact technical support The manufacturer and find out what exactly needs to be done for installation. Requires the driver to the system most often on the disks, as well as on the USB of the last specification, which often happens when you try to put a "seven" on a laptop using a replaceable carrier. Note that the latest specification of this interface for data transmission Win7 "from the box" does not support, so when installing simply use USB ports with an older specification. Usually, latest models The laptops are equipped with a single port of USB 3.0 and a couple of 2.0, so there should be no problems.

More often when installing Windows 7 requires a drive driver, as not all of the old-generation OS disk controllers are supported. To solve this task, you again have to "wool" website developers, communicate with technical support and travel on the forums experienced users. Most often, at the installation stage, you have to connect a floppy drive with the search drivers, but it is much easier to find the versions of the installation d

the claims in which all the necessary components are already implemented. Such can be found on the forums of "happy" owners specific model laptop.

Similarly, it should be done in the case when the installation of Windows 7 requires drivers hard disk. Most likely, the problem again lies in so that you in any case will have to look at the driver on it, persistently appealing to the help of the manufacturer and friendly users.

We hope that you have learned about the main reasons why when installing Windows 7 requires a driver for some devices.

And often incomprehensible novice user - a message that "we failed to create a new one or find an existing section. For more information, see the installation program log files. " (Or WE COULDN'T CREATE A NEW PARTITION OR LOCATE AN EXISTING ONE IN STLICAL SYSTEM VERIES). Most often, the error appears when installing the system to a new disk (HDD or SSD) or after pre-action for formatting, conversion between GPT and MBR and changing the partition structure on the disk.

In this manual, information on why such an error occurs, and, of course, to correct it in various situations: when there are no important data on the system section or disk, or in cases where such data is and needed to be saved. Similar errors when installing OS and how to solve them (which, including may appear after some ways offered on the Internet, correct the problem described here):, (in contexts other than GPT and MBR).

The first of the ways to correct the problem assumes one of two options:

1. On the disk to install Windows 10 there are no important data and everything is subject to removal (or already deleted).
2. There is more than one partition on the disk and on the first of them there are no important data that you want to save, while the partition size is sufficient to install the system.

In these situations, the solution will be very simple (data from the first partition will be deleted):

As you can see, everything is quite simple and any actions on the command line using DiskPart (Deleting partitions or cleaning the disk using the Clean command) in most cases are not required. Attention: The installation program needs to create system partitions on the disk 0, and not 1, etc.

Finally - video Instructions for correcting the error when setting the method described above, and then additional methods for solving the problem.

How to fix "Failed to create a new one or find an existing section" When installing Windows 10 to a disk with important data

The second common situation - installing Windows 10 is made on the disk, which previously served to store data, the most likely, as described in the previous solution, it contains only one partition, but the data on it should not be injured.

In this case, our task is to squeeze a section and release a disk space so that system sections are created there. operating system.

You can do it with both the Windows 10 installation program and third-party free programs To work with partitions of disks, in this case the second method, if possible, use it, will be preferable (further explains why).

We release a place for system partitions using diskpart in the installation program

This method is good because to use it, we will not need something extra, in addition to launched program Installations of Windows 10. Minus the method is that after installation, we will receive a not quite ordinary partition structure on the disk when the bootloader is on the section with the system, and additional hidden system sections are at the end of the disk, and not at its beginning, as it usually happens (In this case, everything will work, but in the future, for example, when problems with the loader, some standard ways of solving problems may not work as expected).

In this scenario, the necessary actions will be as follows:

1. While in the Windows 10 Installation Program, press SHIFT + F10 (or SHIFT + FN + F10 on some laptops).
2. The command line opens, use the following commands in order.
3. diskpart.
4. list Volume
5. sELECT VOLUME N. (where n is the single volume number on the hard disk or the last partition on it, if there are several of them, the number is taken from the execution of the previous command. Important: it should be about 700 MB of free space).
6. shrink desired \u003d 700 minimum \u003d 700 (In my screenshot - 1024, because there was no confidence how much space is really needed. 700 MB is enough, as it turned out).
7. eXIT

After that, close command line, And in the Selection Selection window, click "Update". Select a section to install (not unoccupied space) and click "Next". At the same time, Windows 10 will continue to install, and the unoccupied space will be used to create system sections.

Using Minitool Partition Wizard Bootable to free up space section sections

In order to make a place for Windows 10 system partitions (not at the end, and at the beginning of the disk) and not losing important data is suitable, in fact, any boot software for working with the partition partitions. In my example it will be a free Minitool Partition Wizard utility available in the form ISO Image On the official website https://www.partitionwizard.com/partition-wizard-bootable-cd.html (update: from the official site removed boot ISO. But it is in a web archive if you view the specified page for previous years).

You can write this ISO to a disk or boot flash drive (bootable flash drive can be done using, select MBR or GPT for BIOS and UEFI, respectively, file system - FAT32. For computers with EFI download, and this is most likely, your case can be simply copied All the contents of the ISO image on the USB flash drive with file system FAT32).

Then you load from the created drive (secure download must be disabled, see) and make the following:

After applying the changes, restart the computer from the Windows Distribution - this time an error that failed to create a new one or find an existing section appear should not, and the installation will be successfully (when installing, select the section, and not unoccupied disk space).

I hope the instruction could help, and if something suddenly did not work out or remain questions - ask in the comments, I will try to answer.

Good day to all, my interested readers and lovers dig in their computers!

Yesterday I ran into a problem when installing Windows seven on a laptop of your colleague. That is, the operator did not want to install anything at all. I had to flip almost the entire Russian segment of the Internet, but I found the answer. And today I will tell you why Windows 7 is installed from a flash drive or disk and how can it be fixed.

What causes could be?

Let's imagine that as soon as you try to put Windows on a laptop from a carrier, the computer simply does not see the device. Most likely, the BIOS is not set up the download parameter from it. You need to fix it manually. To do this, when downloading your PC you need to click F2. or Del.. This screen appears.

Go to the BOOT tab (i.e. download), and then choose the very first line. Denoting priority parameters. All as in the image below.

There we see that the first in the list (that is, the most upper) is a hard disk. And you need to set the USB flash drive.

Click on the first position and select FLOPPY DRIVE, which means mobile disk (In the commoner "Flap").

If the solution through the BIOS did not help, most likely, the USB flash drive itself simply has taken its own. This happens quite often, so be ready for it. With frequent use, the medium operates on average for 2-3 years.

Another situation is possible. For example, when installing the system on lenovo laptop Load starts, everything works until the file unpacking starts.

In this case, everything is sad. Most likely, the distribution of the operating system was recorded crooked. Either, the image itself had broken files that are now affected during installation. We will have to re-swing the Windows itself and rewrite it again onto the carrier. Otherwise, you will have to take a license disk.

By the way, even if you are installing the OS from the Bolveshka, be prepared for the fact that the laptop can request the optical drive driver. This, again, means that the distribution itself caught you with an error. In this case, you can simply try to disable your drive in the BIOS and re-start the installation.

Black screen

Imagine the problem. Have laptop asus and carrier with the operating system. When starting the system, the monitor goes out for installation. The presence of a black screen can signal two things.

Hard disk refused. You need to climb into the BIOS and see whether it is determined. If not, most likely you damaged it. If he is still in the list, it means that you need to turn off and then turn on.

There is no driver. It is possible that there is no needed in the distribution itself. By the way, this often happens to windows images 7, which recorded self-taught programmers and allowed errors when assembling the ISO file.

Deputy Clay. From the monitor to the bottom base part of the HP laptop (or any other) there is a cable that passes through the left or right loop of the cover. If you disassemble your computer, they could easily damage the conjunction, or disconnect it by negligence. Remove the PC housing and check.

The computer is infected with a virus. Urgently download antiviruses, such as Comodo Internet Security or AVG AntiVirus Free and scan the system.

NEW HARD

Very often, when buying a new hard drive, problems occur with the installation of the operating system. This is connected with a new device. For correction go to the BIOS and in aHCI mode We find our hard.

All, now you can safely install the OS.

If you have a macro system for UEFI, then the device will be determined automatically, without your intervention, since this type of bios is more modern.

What to do if nothing helped?

First, you should not panic. Most likely, the program hangs due to hardware error, that is, the problem is in the "hardware". Download here from here Program Victoria.

Turn it on, let it analyze your hard drive. Especially its surface for errors, as well as the presence of sewn drivers. If there are bade blocks, then start to save on a new hard, as such problems are not treated. They mean that on the magnetic plate, inside the housing of your hard drive, scratches were formed. It is possible that they appeared from the blow on a computer, or from cutting shake, so carefully treat your car.

It also happens that already after installation, the devices drivers are not found. In this case, you will have to find discs that have been supplied with your laptop. They have the desired software. Or swing here from here - Driver booster. Run it and he scars and installs everything you need.

Conclusion

So I told you what to do if you encounter any of the above errors. Here, by the way, video that will help you figure out what.

Remember that you should not immediately carry your laptop to the service. Money will be guided with you just just for the diagnosis, and not small. Paint my blog, read the materials, in them a lot of useful. Perhaps you yourself decide the problem, and you do not have to upload your blood earned. The main thing, do not try to climb the pieces of iron. Especially in the hard disk. Browse the body - dust will fall, which can lead to full data loss.

On this I will finish this article. I hope you will not find any problems with your computers. In any case, share this material with your friends, familiar and colleagues in social networks. Subscribe to the updates of my blog, and you will always know about the release of new articles! All are good and about new meetings!