ROUTER ASUS IP address by default. All about ASUS routers

In this instruction, I want to tell how to make a reset of the ASUS router to the factory settings on the example of one very common model - RT-N12. Due to the fact that all WiFi routers and the latest versions of the ADSL modems of this manufacturer use the same AsusWrt firmware, this material will be useful to each who wants to reset the router asus settings of any model: RT-N10, RT-N11 VP, and T .P.

How to reset the ASUS router button

On any modem or router produced by Asus, there is a special "Reset" button. It allows you to reset the asus router settings without logging into its web interface. It is very convenient in cases where it illuminated or an error was made in the configuration due to which access to the device management was lost.

The "Reset" button is made in the form of a hole of a small diameter and, as a rule, is located on the back of the device housing. To press it, you need to use the fuction, clip or pin. Usually it is necessary to keep the "Reset" button for 5-10 seconds. At the same time, the device itself must be enabled.
After that, the network device is restarted with the new basic configuration.

Reset Router Asus through the configurator

This way to return the ASUS router to the factory configuration is more convenient if there is access to it over the network and at the same time it is problematic to approach and press the reset. For example, when the device is attached high under the ceiling. Well, or just laziness to go to him.
So, to reset the RT-N12 settings or any other router Asus, you must first use the web browser to go to its settings via IP or domain Router.asus.com.

In response to this, the operating system of the device will ask - exactly do we want to make a reset of the ASUS RT-N12 router settings to the state in which they go from the factory.

Click on "Yes" and wait until the process is not completed at 100%.

After that, you will need to update the page and again go to the router web configurator.

If everything is done correctly, a special master must be launched, which will help you restore the router settings after discharge.

This step-by-step instruction is devoted to how to configure Wi-Fi Router ASUS RT-N12 to work with providers:

Beeline (L2TP)
Rostelecom, Dom.ru (PPPoe).

The manual will include the following important settings: Proper connection of the router, how to enter ASUS RT-N12 settings, configure Internet connection, configuring a wireless network protection (Wi-Fi password).

How to connect ASUS RT-N12

Despite the fact that it seems obvious, all the instructions begin with exactly how to connect the router correctly, because even here there are errors, because of which the Wi-Fi connection is not working.

From behind your router there are five ports - four LAN ports and one WAN port (Internet). It is to the last one, which differs from four other ports, you should connect the cable of your Internet provider - Beeline, Rostelecom or any other.

In addition, I recommend setting up a wireless router from a computer or laptop that has a wired connection with it for which one of the LAN ports on the router with the same port on the PC network card should be connected.

And the last moment: it is advisable to check the settings of the connection in Windows () - this step can now be skipped, but if you fail to go to the router settings, go back first to it.

Do not forget to turn on the device into the outlet. And also, for all subsequent steps, disconnect the Internet on the computer, (if you have a "high-speed connection", "Beeline" on the PC itself) active should be active on a local network.

How to go to the router settings

On the back of the ASUS RT-N12 (as well as on other routers), there is information about the address, login (username) and password - they need to be used to log in to the web interface of the settings. In order to go, run the browser and enter the specified address in the address string, for Asuseto routers 192.168.1.1.

When you are asked to enter a login and password, enter admin.for both for the other (provided that you did not change them during previous attempts to configure everything).

And now attention: If this is the first time you went here after purchase or if you just dumped the router, automatic setup will start - you will need to press "Next" and fill off the proposed fields.

You will be prompted to change the password to enter the "admin" of the router (the one that was admin), after that an attempt to determine the type of connection and, if it is determined, you will be prompted to enter a login and password on the Internet, and then - set the name Wi- Fi network and password on Wi-Fi.

I will not describe automatic setting. If it goes successfully (and it may be so for Rostelecom and Dom.ru), then my instructions you do not need - as a result you will fall to the main page of the ASUS RT-N12 manual settings, and the Internet will work. If after that, the Internet did not earn, then I will tell you how to configure everything manually.

Configuring Beeline Connection

In order to configure Internet Beeline on ASUS RT-N12, on the main settings page, click on the left "Internet", and on the page that opens, fill in your connection settings as follows:

Wan Connection Type - L2TP
Username - Your Login Beeline
VPN server - tp.internet.beeline.ru

And save the settings. If you all entered the correctly, and the Beeline connection is broken on the computer (this is necessary), after half a minute, the router will set the Internet connection and in a separate browser tab, you can open any sites, and connected via Wi-Fi phones, tablets and laptops will also have access to the Internet.

You can proceed to setting up a wireless Wi-Fi network if you want to change something in its parameters (below in this manual).

Configuring Rostelecom, Dom.ru (PPPoe)

To configure the Internet Rostelecom or Dom.ru on this router, press "Internet" in the menu on the left, after which fill out the fields offered as follows:

WAN Connection Type - PPPoE
Get an IP address automatically - yes
Connect to the DNS server automatically - yes
Username - Your Login Rostelecom or Dom.ru (for the Internet)
Password is your password for the Internet.

The remaining parameters are not needed. Save the settings and, if everything was done correctly, after a short time the Internet will be connected to the router, and you can open the site and everything else from this computer, as well as other devices connected to the router (at the same time, high-speed connection on the computer must be disabled ).

If required, configure the wireless network parameters - its name and password.

Configure Wi-Fi Wireless Network Parameters

To configure Wi-Fi, in the left menu, select "Wireless Network", then set the options you want.

Routers or routers allow you to carry out the wireless connection of several consumers to the Internet. ASUS brand devices thanks to the optimal combination of price and quality were widespread. For efficient operation, you need to enter the correct parameters of its operation. To do this, you will need to log in to the ASUS router settings. Tell how to do it.

Enter the equipment settings and adjust them besides the personal computer or laptop is also possible using a smartphone or tablet. Make changes to the function parameters are best at the cable connection with the consumer. Setting up a wireless network router can lead it to

Attaching the peripheral device to the router using the supplied cable does not represent any complexity.

In one end, it is inserted into the LAN slot of the router, another - to the computer connector corresponding to the configuration.
Then the router connects to the power supply network, the main Internet cable located in the WAN connector can not be disconnected.

Wireless connection

The network broadcast by the new router is publicly available to connect to it does not need to enter the password. It will be called in most cases ASUS and the icon with the highest signal level will be placed nearby. The connection is carried out:

If the router was used earlier or an unknown password is installed on it, you need to return it to the factory settings. On the housing, there is a hole with a small diameter, indicated by the "Reset" inscription. It contains a button that should be press and retaining about 10 seconds with a thin sharp tool like the needle. Device parameters Back to factory values.

We enter the router settings

In order to get into the ASUS router administrative control panel, the following steps:

Step 1. The consumer is connected to the device using a cable or wireless network.

Step 2. From an open browser, log in to the router settings menu. To access the router settings, its IP address will be required. You can find it using a cable connection or in the access menu of wireless networks. In addition, the input data is indicated on the sticker located in the rear of the body of the instrument.

On a note! Of course, if the login and password changed earlier, new data should be entered. If they are lost, you will have to restore the factory parameters of the router according to the method described above. The admin panel opens.

Included with the device comes recorded on disk software. It contains useful utilities, and instruction manual. With it, it is easiest to change the ASUS router settings.

Sometimes after performing these actions, the administrative control panel of the router does not open, and the inscription appears: "Page is not available." In this case, the following should be taken:

with a wireless connection, check the parameters of the passage of the IP;
if the automatic receipt of the address is activated, and the error remains, you need to connect using the cable;
check the integrity of its compound;
in the LED display on the router housing, make sure that the electrical power supply of the device.

In addition, you can try to enter the administrative control panel of the router using another Internet traffic consumer.

Conclusion

In conclusion, we note that the entrance to the settings of the ASUS router does not represent much difficult. Following the items of simple instructions, it can be performed independently, without resorting to the help of specialists. The firmware is better to carry out the cable connection. Changes made on a wireless network may result in equipment damage.

Video - How to go to the settings and quick setup of the ASUS router

The entry procedure in ASUS's routers does not have special differences from other router manufacturers and routers. Nevertheless, many users have problems with this, because it is often required to enter your router settings to, for example,

In this article we will tell you how to go to the ASUS router and what to do if I forgot the password from it.

Where to begin?

As soon as this condition is performed, open any browser and try to enter the following IP addresses alternately and press "Enter":

192.168.1.1
192.168.0.1

Input in the address bar of the browser IP address of the router

Enter login and password from the router (default Admin, Admin)

Here I enter the default login and password values \u200b\u200b- admin.

If you changed default values, then enter them.

As soon as the correct combination of authorization data is entered, you will fall into the settings of the ASUS router.

ASUS router settings view

What if the login and password from the router does not appear?

In this case, the fact that the address space was changed in the settings. In this case, you can familiarize yourself with, in which we told how to find the IP address of the router.

You can also simply reset the router on the factory settings by long pressing the RESET button on the back of the router.

RESET RETTER button RESET

In this case, all settings will be reset to the factory and IP address of the router can be viewed on the bottom sticker.

Factory login password and ip address of the ASUS router on the bottom sticker

How to enter the ASUS router if you forgot your password?

In this case, as in the previous one, only a reset to the factory settings will help you. After that, the password and the IP address will become standard, that is, those that are written on the sticker at the bottom of the router.

It is worth considering that if you reset the ASUS router to the factory settings, then you will most likely stop working the Internet and Wi-Fi. In this case, it will have to configure again.

In this article, we invite you to familiarize yourself with the instructions for setting up the ASUS router by following the data of the router on the admin panel using the data provided for this.

Routers from the ASUS manufacturer Some of the most popular and common in our country, especially the models: RT-AC51U, RT-AC68U, RT-N12, RT-N16, RT-N11P, RT-AC3200, RT-N14U, RT-N66U, RT -Ac87U, RT-AC66U, RT-N56U, RT-N56U. The process of their setup is not much different from the setting of equipment produced under other brands, but there are still differences. Therefore, we decided to create separate instructions for Asus routers.

ASUS equipment setup We produce standard:

Connect to the router using a power cable or via the Wi-Fi network.
Using any browser, go to the control panel.

Please note that you can easily enter the settings and make their change, not only from a stationary PC, but also from any mobile device: tablet, smartphone. However, it is more convenient to do this using a stationary PC or laptop. At the same time, it is better that the device is connected via the cable, but if you use a wireless connection, then consider the router firmware should not be carried out using Wi-Fi, because A great probability instead of a working device to obtain non-working equipment.

Input to the ASUS router settings - 2 ways to connect

In the case of the connection of the router to the computer, this page-instruction can be scrolling below, as we start from the connection process.
If you have no connection, it must be installed in one of two ways: through network cable or Wi-Fi compound. Consider both options in more detail:

Connect to router through network cable (Network).

Everything is very simple: we take the cable that comes with the router and connect it to the device using the LAN connector. The connectors are signed and therefore the error here is minimal, since you can choose any of the four (see figure below). The second end of the cable is inserted into the system block connector or laptop. This is how it should happen:

Now you need to connect the router power. Disable WAN cable, which is connected to the device? You can not do this, this cable does not place the correct setting.

Connect to the Wi-Fi router

If you have already previously configured the connection to the ASUS router, then it will not be any problems for you. In the case of a new router, immediately after switching on, it will begin to search for a wireless network that will be called ASUS in most cases.

The network will be without a password, and you just need to join it by clicking on the network and choosing " Connect«:

How to go to the ASUS router settings, if you forgot the password from Wi-Fi?

If you do not remember the password from Wi-Fi and there is no way to find out with other connected devices, you will have to use a wired connection. If the cable is not, then you can do this: reset all the settings of the router to factory and set the settings again. To reset the ASUS device to factory settings, you must click and hold 10 Seconds button Reset..

Entrance to ASUS admin at 192.168.1.1

After connecting, you must open any browser in the address bar Register the address: 192.168.1.1 . Go to this address. If the configuration of this router is performed for the first time, the page will open where the settings are displayed. Find in these settings to the quick setup of the ASUS device. Password and login request appeared? Use standard, for example, login admin. and password - admin..

Of course, if you previously changed the password and login, then enter your own. If the password and login are replaced, but now you cannot remember them, then you need to reset the settings to the factory, as described above.

Where to get the address that is prescribed in the browser address bar to access the settings? It is indicated on the case of the router itself. Here:

Don `t come in In the router settings? What to do?

The answer to this question depends on what error and at what stage of the process you have. Some users face problems when connecting to the router, many in a thom or different browser do not open the settings and the message appears. the page is not available". These are the most common problems and to eliminate them can be tried to do the following:

Check the IP receipt settings if you are using a local network or wi-fi. Read more in the article;
Check in the Network IP settings, and the problem did not disappear, then try using a network cable.
If the connection initially was carried out by cable, then it is necessary to check the correctness of its connection.
Make sure the router is connected to the power grid (the red indicator should flash).
Try to go to settings from another device using a cable and wi-fi.
Reset the router settings to factory and try the connection procedure again.