What are the antenna connectors in the Yota router. We make an external antenna to enhance the Yota signal with your own hands

Network of base stations expanding operator coverage area mobile communications, grows. The signal quality is improved, and the connection speed increases. But not in all places it is possible to enjoy the super-speed Internet 4G LTE, even by purchasing Yota modem 4G.

Causes of a weak signal:

network overload users;
significant remoteness from the base station (characteristic of small cities and villages);
the place where the modem is located: height, material and wall thickness;
located near interference in the form of multi-storey buildings, forest arrays, electromagnetic fields from high-voltage power lines.

Allow the 4G signal amplification problem can be installed antenna for the Yota modem.

Types of antennas and benefits of their use

The Specialization of the Yota operator is the provision of Internet using high-speed 4G networks. The company sells, in addition to the Yota 4G modem, various modifications of the router, antennas.

Types of industrial antennas:

4G panel antenna directional. It has the function of automatic transition to a 3G signal if the 4G network is missing. There are modifications to work in two frequency ranges;
Parabolic. 4G antenna having a maximum reinforcing coefficient. It is good to apply when the base station is at large distances. It can be used where the signal is completely absent. Disadvantage - high cost;
Circular omnidirectional. Mobile, has a magnetic database and the possibility of installation in different places, including in the car. Does not differ in a high power of amplification and is used in zones with an unstable signal reception;
Internet signal amplifiers are room antennas. Connect to the modem using a USB cable.

Important! There are antennas for Yota with built-in modems and routers. If you need to enhance the signal on the already existing device you need to buy antennas without a 4G modem.

If the modem is not yet, the purchase of a combination device will cost cheaper than the purchase of elements separately.

Antenna Yota provides an increase in the speed of the Internet up to 10 times. Installing the equipment and its configuration will be under power to any user who does not have special knowledge.

Homemade amplifiers

If the subscriber is technically prepared, then they can be made an antenna for Yota with their own hands. At the first stage, the placement of the nearest transmitting center is determined, it turns out, there is a lot of interference in the area of \u200b\u200bdirect visibility. Sometimes the connection is not possible even using the most efficient amplifiers. In major cities, the tower, which is in hundreds of meters from the place of residence, can give the same quality of the 4G signal as in a rustic area at a distance of 10-12 km. This is explained by different network coupling.

Need to contact B. service Yota For necessary information About the nearest tower. There may also be a consultation, as the external amplifier can be correctly positioned. Other data search options are a forum on the provider website, third-party Internet resources.

Antenna for Yota using aluminum jars

The launch of the amplifier for iota is simple, but will not provide an increase in the speed and stability of the Internet in conditions of too weak signal. However, such an external antenna is able to add missing stability in the work of LTE compound. Used exclusively indoors.

In the side surface of the empty cans from under beer or other beverages, a hole is drilled in the form of a modem of Yota. The distance to the center of the velocked hole from the lower surface of the cana is calculated using a special calculator for similar homemade structures. It can be found on the Internet. It is necessary that the transmitting center guide the signal to the amplifier with the smallest interference. By changing the depth of placement of the modem and gently turning the jar towards the tower, you can configure the manufactured antenna on the reception of the signal. The site of Yota is controlled by the Internet and Ping connection speed. Computer modem with an antenna connects through a USB cable extension.

The design resembles a cannon antenna, but with a larger reflector area. The reflector can be a cardboard box, with a plated foil surface, a stainless steel pan, aluminum bowl, metal grid, etc. The Yota modem is fixed inside the tank with screws installed in the side drilled on the side of the hole, or using other devices.

Pseudo-seater can be fixed outside the building, while protecting the modem with a polyethylene film or a plastic tube. If you correctly orient the homemade design, the 4G signal will significantly increase.

Important! Based on the practice of making pseudo-cellulite, the modem needs to be placed perpendicular to the ground, in parallel to the surface of the reflector.

Experienced users note the reliability and simplicity of the Harchenko - thick copper wire antenna, curved in the form of "eight". All sizes indicated on the Internet for this design must be clearly respected. The wire is fixed on top of the reflector, which can serve as an aluminum plate. Wire insulation from the reflector is ensured. The antenna is configured to the frequency of its operator.

The design of the design is made on the street. You need to know where the transmitting centers are located to send it to one of them if possible, avoiding noise. Probably get a powerful signal strengthening, placing the amplifier at sufficient height.

Important! The cable from the antenna must be connected to the modem through the connector that may not be. Then the modem is disassembled, and the soldering is performed directly on the printed circuit board.

Use satellite plates

Television satellite plate - good decision To obtain a stable Internet connection in problem areas. The eet modem is placed in a small plastic container (tube or a bottle of yogurt) and fixes in the focus of the plate, where the television converter is usually located. Computer connection is provided by a USB cable. More difficult to configure antenna.

Moments that need to be taken into account when setting up a parabolic antenna for Internet receiving:

Unlike the setting to the television satellite, the plate for the LTE signal is sent below. This is due to the revision of the reflection;
To accurately tuning during the slow rotation of the antenna, tracking computer Program Yota Quality Changes Connection with the Internet. At the point of the best signal receipt, the directional plate must be fixed;
After fixing the external antenna, you can try to change the location of the focus and see how the 4G signal changes. The Yota modem must be installed so that the USB port is from the opposite end of the plate;
If the 4G signal retains instability, it is necessary to raise the design above. The signal amplification will give a larger diameter of the plate. Satellite meter diameter antenna can guarantee a high-quality connection to remove 8-10 km from the tower;
Simultaneous use of a satellite plate for receiving a television signal and improving the quality of the Internet connection is impossible.

The directional antenna having a patch reflector of a parabolic form will give the best strengthening. But it is difficult to find such a constructive element for the manufacture of antenna, the industry is not issued due to outdated standards. Although the finished designs of this type are on sale.

LTE signal strengthening is performed with both industrial antennas and hand-made. Homemade antenna requires the presence of certain knowledge and skills. If the user does not possess them, the modem may be damaged. In this case, it is better to purchase factory instances in accordance with the existing conditions.

Video

Mobile Internet from Yota is for many users the only alternative to wired providers. In some places it is simply impossible to pave home phone or optics. Cellular networks come to help people. But here you can encounter a small coverage area. In such a situation, the external antenna for the Yota modem will help - it will strengthen the signal and makes the connection more stable. Our review will tell you what to do.

Analysis of forums and official publishes of Yota showed that many users are unhappy with the coverage area. In places where the signal from base stations is too weak, regular problems with communication are observed. The most common complaint is at low speed. Files are not downloaded, pages open slowly and with errors, delivery will be delivered by messages in messengers. Without dealing with the problem, the subscribers begin to blame the operator in everything, although he is here and with nothing.

Communication breaks - a modem simply loses a connection with the basic stations YOTA. Repeated connection May take a few minutes, as it all depends on the power of the signal. In bad weather, the connection is often missing completely. The thing is that the precipitation slightly muffle the already weak high-frequency signal.

If in big city The problems with the reception are rare, then outside the cities, the situation is only worsening - in small villages and villages, the reception is bad, the same applies to country partnerships. And after all, it is here that the whole army of subscribers who need high-speed Internet lives. But a weak signal often makes it impossible to enter the network.

How to strengthen the signal

The most interesting thing is to complain to the operator almost useless. You will take contact details, clarify the location, after which (with a probability of 99.9%) will say that everything is fine - try changing the location of the modem. But in most cases it is impossible to change its position - do not climb on trees with a modem in hand. In our situation, the outer antenna for the Yota 4G modem will be helped. Let's see what we can buy in stores:

Simple room external passive type antenna - looks like some satellite antenna embryo. It seems like focusing a weak signal to the problem mounted in focus. Users do not particularly praise such antennas.
Special aimed antennas - provide acceptance even in the most sophisticated conditionsBut differ in high cost. Above such devices installed amplifiers that enhance the signal in both directions. The gain of such devices is from 16 dB to 24 dB (these are very decent indicators).
Simple directional antennas like "Wave Channel" - not the best option at a strong distance from the nearest base stations. Another thing is that this option is one of the cheapest.
Sector external active antennas for outdoor installation - small rectangles in all-weather execution. Great to work with 3G and 4G signals. It is cheaper than the "Wave Channel" antennas and exceed them in efficiency.
Parabolic antenna - similar to satellite, ensures good strengthening yota signal in passive mode.

Also here you can include various homemade solutions.

What you need to connect antenna

To connect the Yota LTE exit antenna to the modem, you must make sure that the 4G modem has appropriate connectors. For example, presented on sale in currently The model is equipped only with a built-in antenna. External to it do not connect. But there is still a way out of the situation - you can install such a modem in the focus of parabolic (satellite) or simple room passive antenna. For more professional solutions, connections will be required.

Popular iota modems with external antenna:

Huawei E8372 - The model received many positive user ratings, the cost is about 3,000 rubles.
Huawei E3372H - modem with two connectors for connecting an external antenna. The price in stores is about 2.5 thousand rubles.
ZTE MF832D - inexpensive modem with input to connect an external antenna. Cost - 2290, but according to reviews it is not the most stable option.
Yota B315 Internet Center is not a modem, but a whole router with support for outdoor antennas.

To accommodate the external antenna Yota, you will need a high pillar. It can also be installed on the roof of the house. The most difficult thing to calculate, in which side there are nearest basic stations Yota and in what direction they look. You can get such information on specialized private resources on the Internet.

Also on the Internet you will find advice on modem refinement - you will need to fall to it connectors (if there is a technical capabilities).

The external antenna Yota LTE will significantly improve the reception and will provide more or less high-speed Internet access. But for some subscribers, installation may seem quite complex process. If you do not have enough technical knowledge, refer to specialized companies involved in installing antenna equipment. The cost of work will be high, but they will be able to conduct tests and find out the feasibility of assembly work.

Popular model antennas

Next, we will look at the most interesting antenna devices that can be purchased in domestic shops and online stores. We will affect how simple modelsAnd professional - more expensive and efficient.

Antenna Yota Mimo.

It is more correct to say that this is an Internet signal amplifier called Ramo "LTE MIMO Indoor". To connect the modem, you will not need cables, for mounting equipment, high pillars are not needed. This is a room in which the modem needs to stick and connect the antenna connectors to it. Power is powered via a USB cable, the gain coefficient varies within 9-11 dB. The cost of the device is minimal - only 990 rubles. But in the difficult conditions of receiving Yota, the gain may be insufficient.

There is also a similar solution for modems Yota without antenna nests - this is Ramo "Connect 2.0" for 800 rubles.

Pins antennas

It is difficult to highlight some kind of defined model, as their dozens and even hundreds. The cost is within 1000 rubles, the average amplification coefficient is 9 dB. The reception part is fixed on the support-suction cup. This external antenna can be installed outside or inside the house. Also allowed in the car.

Please note that when ordering such an antenna on Aliexpress, its cost will be from 300 rubles. Minus purchases in China - a long time waiting for the order.

Vegatel Ant-900/2700-Po

We have an all-weather external antenna for the Internet of the sector type Internet, is installed on the wall or on the mast. The enhancement coefficient of the Yota signal is up to 10 dB. The device is made in a solid waterproof plastic case. Experts argue that the complete cable should be sent to the garbage and purchase a cable of another brand, characterized by a smaller signal attenuation. The cost of the model is about 1,500 rubles.

MIMO 18 dB panel antenna Box 4G LTE / 3G

If you are looking for an external MIMO 4G antenna with a built-in modem, pay attention to the presented model. It is more correct to say that the modem is not embedded here, and the built-in - remove the cover from the waterproof block, install the Yota USB modem there and close the block. The gain is up to 18 dB, the cost of the model is about 7,000 rubles.

Hite Pro Grid SMA

This external antenna is parabolic, it provides a powerful gain of up to 2x24 dB. The antenna is very large, but she has an excellent orientation diagram - there is a chance to organize the Internet reception in the country at a significant distance from the base stations of the operator. At the same time, it differs more than affordable price - about 9000 rubles. Be sure to look at this model, if you live away from the city and have difficulty with the reception of the Yota signal.

M-Tech Dual Band Box

Before us, the outdoor antenna Yota 4G LTE cost is only 7.5 thousand rubles. It works on two frequencies - 800 and 2600 MHz, providing confident reception of the signal. The gain at a frequency of 800 MHz is 2x14 dB, at a frequency of 2600 MHz - 2 × 21 dB. To work, the product requires a Yota modem with connectors for an external antenna (TS9 or CRC9). Install the modem into the sealed box, send the device towards the nearest base stations and try to enter the Internet.

What to choose as a result

If your modem has an antenna socket, then best options It will be an antenna on the street. In the street conditions, the reception is always better than inside buildings. And if the antenna system is mounted on an antenna pillar or on the roof of the house, then efficiency will increase. We recommend looking at panel or parabolic antennas. To work inside the city apartment there is a fairly simple pin model. If you can not cope with the installation yourself, contact those who are engaged in installing Yota antennas professionally.

Please note that the antenna equipment for the Wi-Max standard modem may not approach 4G LTE modems.

If you have a desire to learn how to work with micro routers and become a specialist in this area, I recommend on a program based on information from the official course. Course standing, read all the details on the link.

This article is part of a single cycle of article pro.

Introduction

In the warm season, and not only, in the summer, just more often, I spend a lot of time outside the city in the suburbs at the cottage. I also work there. In order to work normally, we needed a stable Internet, which for a long time I did not have, and I frankly suffered. Forced to stay in the city for work. My home is located in a very remote and quiet area, next to the forest, which is a certain plus from the point of view of silence and delicacy, and at the same time minus in terms of communication.

Directly cellular It works less normally, you can talk. But with the Internet there was a frank trouble. Operators are caught all, but the Internet "no". I barely catch 3G. Yes, and prices have never been happy. To work normally, I need a lot of traffic, I didn't really want to pay for it on the existing tariffs, so I did not work much.

Everything has changed when I tried the Yota operator with her unlimited Internet. As soon as I saw that my house seems to be in the coverage area, I decided to buy a simony to start and check the connection. I can install 2 sim cards in my smartphone, so I began to use it as a second. I liked the tariffs by the fact that there is no roaming throughout Russia, which is very convenient. I used the Internet in the smartphone when I left the home area.

With this smartphone, I arrived at the cottage and checked the connection. A miracle did not happen, as the Yota works on the same basic stations as a megaphone, therefore the connection was the same as a megaphone, practically no. The Internet was not very convenient to use, the connection was constantly broken, although sometimes something worked out. In general, I was in the zone unsure reception 3G. I decided to turn the next thing: climbed into the attic and put the phone from the window, which goes to the side, where the nearest base station is located. Began to check the connection and was very happy. It has become much better, the Internet worked tolerably on the phone itself, sometimes LTE was caught.

It was very inspired me and I decided to turn on the access point on the phone, leave it in the attic, and from another floor it is connected to the point and work. I first got acquainted with limit Yota..

Restriction Yota.

The essence of the restrictions of the Yota is that she has different tariff plans for different devices with different costs. I had a SIM card with the cheapest tariff, which allowed unlimited to use the Internet on the smartphone. If you try to distribute the Internet to other devices from a smartphone, then Yota determines and displays a page with a warning that it is prohibited on your tariff, but if you want to use the Internet, pay for it separately.

I went to find a look at this topic. It turned out that the topic is very popular. To circumvent restrictions at that time it was enough on the computer install TTL 65, if you have a smartphone on android, and that's it. The bottom line is that on the TTL smartphone itself 64, if 65 will be on the computer, then from the smartphone these packages will fly away from TTL 64 and the Yota will not know that you distribute to someone else. It helped me. For a while I used the Internet so. But with a chance I decided to change something. I'm tired of constantly climbing the attic to install a smartphone, I wanted to distribute the Internet and on other devices, the smartphone was discharged from the operation mode as an access point. His battery is quite powerful, I have enough for the day of work, but still did not like such a scheme. Sewing the Internet to other devices, by the way, learned. I had a handwritten phone. I put a software on him, which already changed the TTL of all flying packets on SMART.

It was necessary to solve the issue with the quality of communication. Here I have already seriously deepened in the topic and began to select a decision under my situation.

The choice of antenna to enhance the LTE signal Yota

He read the forums on the strengthening of LTE signal, began to understand the antennas. The hope of success gave information that if you at least somehow a signal is caught by the phone, the antenna will accurately help and will be much better. That is, improving an existing signal is not a problem. Pickles arise mainly where the signal with normal phone No at all.

As a result, I bought myself - antenna Panel directional MIMO 3G / 4G LTE, 20 dB (1900-2700 MHz) - http://450mhz.ru/antenna/?id\u003d207. Includes 5 meter wires. It was enough for me, I did not buy additional wires. But we needed separate adapters to connect this antenna with uSB modemohm. I bought these - http://450mhz.ru/accessories/?id\u003d91. For the oscillating antenna to the wall of the building you need to buy a separate bracket. I bought such - http://450mhz.ru/accessories/?id\u003d215.

Install an antenna for high-quality reception is necessary in the direct visibility of the base station. It should not be closed by folds of terrain or other buildings. Sense from her in this case will be not enough. I was lucky, my house is quite high and the attic view of the base station is not blocked by anything, just above the spurious roof passes.

Unfortunately, I could not consolidate the antenna to the bracket. I just have no opportunity to do it. The height of the house is large, the prefabricated stairs are very unreliable at such a height. It is impossible to operate tool on them, and even more harder the antenna, it is heavy. In addition, then you need to adjust it correctly, check the connection, turn, it should be done from it from several times. The option would cause the lift and install from it, but I did not go to it, because after the lift is left, I will not have access to the antenna in general, I can not be able to independently be due to the need or check .

It was necessary to assemble along the wall of the house, either on the roof somehow mounted. In general, difficult. I got sick with low blood. I installed the antenna in the attic next to the window and sent to the base station. Slightly twisted, rotator, blended in different directions and chose the optimal position.

This turned out to be enough in order to appear confident reception at the lower border. That is, from 5 sticks, I have stably caught one, sometimes 2. The signal was stable, speed 1-5 megabit. I am enough for me to work. And for the rest. But I want of course more. I think the signal will be even better if the antenna takes to the street and set the same on the crowning higher. But not yet invented how to do it.

Selection USB Modem for Yota

The antenna had to be connected to the modem. According to reviews on the Internet, I chose a model that was guaranteed to work with the SIOTA sim cards. It was Huawei. E3372. / 827F / M150-2 - 4G LTE / 3G USB http://450mhz.ru/usb_modem/?id\u003d192. In the store I bought an already stitched under all Moscow operators. Inserted the SIM card and immediately all worked when the modem is connected to the computer. Or not immediately. I don't remember exactly, I did more than a year ago. I will try to reproduce the entire sequence of my actions. Most likely the modem earned with some other operator, which I checked. I had a simka from Yota for a smartphone, it is unlikely that it just will work in a USB modem.

I found on the Internet a more convenient firmware for the modem and reflash it, simultaneously replacing IMEI, taken from the old broken phone. I found all the information on working with the modem on the 4pda.ru forum. I tried to search for those instructions for which I did, but I did not find it. There is a lot of information, but exactly what I used, I was not caught. Therefore, I will describe only the sequence of the valid that performed. You yourself are looking for fresh instructions for this, there are many of them, I just watched, you need to take a modem and try. I have nothing to check, I don't want to pull the working modem.

I stitched the Huawei E3372 modem with fresh firmware Hilink..
It seems to be separately installed some more convenient web interface, I do not remember exactly.
Replaced IMEI modem, taking from an old phone.
Installed TTL Fix. He was in the form of a small patch.

After that, I could simply insert the Simka Yota, a modem into a computer or router and use the Internet. The first time everything was fine, the farther, the more often I began to receive a page from Yota with a warning about restricting the distribution of the Internet. He began to read the information and realized that only TTL Fix was insufficient. Yota began to a second one who uses the Internet for resources to be accessed. For example, if you have a sim card for a smartphone, and you go to Microsoft update server, or play an online PC game, it is obvious that you distribute the Internet and you need to restrict access.

The first time it was enough to make changes to hosts file On computers, limiting access to resources. The list of resources was looking for on the Internet. But over time, the restrictions appeared more and more often. For example, I noticed that Internet access immediately stopped as soon as I updated the ports on FreeBSD in virtual Machine. Everything else, the Internet began to use other devices - phones, tablets. To customize the lists of restrictions on them all was very difficult or impossible. I began to solve the question dramatically. Eventually .

I ran a little forward without told about uSB connection Modem to microtist.

Setting up USB modem with Yota on Mikrotik

We have an antenna, the modem will flash under the yoy and ready to work. It remains to connect it to router Mikrotik And set up the distribution of the Internet from Yota. With the help of adapters, connect the antenna to the modem and stick it to Mikrotik. I got like this:

My microtic RB951G-2HND with version 6.33.3 version was determined by a modem. I did not have to set anything. The list of interfaces appeared a new title lTE1:

Since the DHCP server is already built into the Hilink firmware, you need to run in the microtus dHCP client On the LTE interface. You will receive an address from the range of 192.168.8.0.

On this, I have everything in my Internet through Yota in a fence house.

Conclusion

I will summarize what was done. At the points I will build all the sequence of actions.

Bought Sim. map Yota. And I was convinced that at least some signal is caught in the country.
I bought a USB modem and reflash it to work on the Yota network, replaced IMEI and installed TTL FIX.
I bought an antenna to enhance the 4G / LTE signal, adapters and connected it to the modem.
I connected the modem to the microtic, set up the distribution of the Internet via WiFi.
Configured OpenVPN Client on microtus to mask Internet traffic from Yot.

On the this moment This configuration works successfully. I have no doubt that after some time there will come up with some new scheme Locking unauthorized distribution of the Internet from tariffs that are not intended for this. We will think then how to do.

I already have an idea how you can overcome future locks from Yota. I even thought to use it now. For example, through the use of RDP to another computer and work on it. On the local computer Disable all connections other than RDP to the specified address. Of course, it is not as convenient, and from other devices will not work out. But it is not very scary. I need the Internet in the main work, and it is even more convenient to me through RDP in some cases. I use the Hollow and customized working environment, which is available from anywhere. If the Internet is stable, then it is practically convenient to work as well as for the local work desk.

And everyone else let nature relax from their gadgets and the Internet. For health is useful. I am waiting for advice, comments, tips on writing. Perhaps someone will offer a simpler and convenient option. I will add another that when I leave, I take a modem with myself and I use as needed in Moscow or somewhere else. Very comfortably. I consider it a significant plus of my decision. Paid unlimited Internet always with me.

Just in case, I will also give a reference on the basis of a microtic. The topic is relevant just for the fence house, since the severity of the solution based on the Microtikov Capsman is very conditional and in Enterprise is not suitable everywhere. But for home use Just once - budget and simple.

I remind you that this article is part of a single cycle of article pro.

Online courses on Mikrotik

If you have a desire to learn how to work with microtic routers and become a specialist in this area, I recommend going through the courses on the program based on information from the official course MIKROTIK CERTIFIED NETWORK ASSOCIATE. In addition to official program, courses will be laboratory worksIn which you can check and consolidate the knowledge gained. All details on the site. The cost of learning is very democratic, good opportunity Get new knowledge in the subject area currently relevant. Course Features:

Practice-oriented knowledge;
Real situations and tasks;
The best of international programs.

Exterioryota antenna - a simple solution to a big problem

The Yota amplifier, as you can guess from the name, is nothing more than an external (installed outside the housing) receiving-transmitting module, made in the form of a street or room antenna, compatible with the modem and routers manufactured under the Yota brand. It assumes the functions of their regular low-power antennas, increasing the integrity and data transfer rate.

Wireless Internet from Yota is such a thing ... often it does not reach the speeds promised by the operator. It is not surprising that the Yota amplifiers enjoy the population with such great demand, which is not just remained unchanged over the years - it is steadily increasing. After all, for many, the amplification of the Yota signal has become a real "headache" - a problem that is seen intractable.

However, exactly until they percade the electronic store site, where you can always buy an antenna for Yota, and not just buy, but this is the most profitable price in the city! The solution of many years of Internet problems, as practice shows, probably not take you not only much time, but also money. Not so serious was this problem if you figure it out ...

How not to make a mistake with the choice of antennaYota.

However, it is not necessary to assume that it will be able to allow it absolutely any antenna for Yota, which you purchased on the occasion of the subway. Such purchases are rare when it turns out to be successful, and therefore you do not need to lay great hopes on them ..

What do we mean by the word "good"? This is such an amplifier for Yota, which will be the same efficient and in the city feature, where the neighboring buildings are closed by radiation of base stations, and beyond where the base stations are strongly removed. Problems with the use of wireless Internet arise everywhere, but you no longer need to worry about them - they don't touch you now!

Having preferred an electronic store site, you are guaranteed to get an effective amplifier of the Yota signal, since others are simply not in our assortment. All you have to do is to determine the technical characteristics that directly depend on technical characteristics You use the Yota device (modem or router).

Objective signs of a good antenna foroTA

Not least materials from which are produced by our amplifiers for Yota have not latter. External antenna, even if it is used in the room, and if in the open space - so in particular, should be made of high-quality weather-resistant, but at the same time do not create interference materials. Otherwise, the Yota amplifier is not that will not provide due efficiency, but will not work for a long time.

Distinctive features forYota.LTE

External antennas designed to enhance the Yota LTE signal (Yota 4G) have become widely demanded relatively recently. The wireless networks of the fourth generation, which came to the major cities of Russia, did not fully, because of which many subscribers were not able to enjoy the traffic and stability of the Connect.

According to its design and the principle of the antenna, the Yota LTE is no different from the antennas intended for use in the networks of previous generations. The difference lies in the data standards supported by it, which are more demanding and to the receiving, and the radiative antenna capabilities, as well as in technologies and devices developed under them.

However, in the same measure as the external antenna Yota, it concerns cable products and connectors used to attach it to the same names and routers. LTE amplifier for YOTA, if it has been connected using low-quality cables and connectors, can lose up to 15% of the received and transmitted signals, thereby crossing all the advantages of its use ...

About the harm low prices on antennasYota 4.G.

But back directly to the Yota LTE signal amplifier. All of them are developed taking into account the most modern achievements in the field wireless communication And therefore no complaints are called. Developed by many companies from the USA, China and some other countries, because for LTE, if you believe international experts, the future, and for its commercial use - a big benefit!

The situation spoil small producers, who, wanting to make it easier to reduce their products (including Yota LTE antennas), use absolutely unusable materials that are capable of any, even the most brilliant project to turn into a "non-viable freak". Examples of this - thousands. Their lion is made up of Chinese-made antennas, intended for use in conjunction with USB modems.

External antennas for Yota (to enhance the signal of the said operator) are presented in Russia very widely. Buy the Yota 4G amplifier today is not a problem, it is in another - in his choice! The latter is quite difficult to the innumerable manifold of trademarks, among which are extremely little trustworthy. Often the buyer has to choose between bad and ... bad, in our opinion it is unacceptable.

Amplifier for modemYota at a bargain price

Fortunately, you are on the website of the electronic store site, whose clients who have decided to purchase one or another device for Yota (signal amplifier, for example), do not face similar problems. The Yota LTE external antenna bought here will certainly be summarized by providing perfect reception and data transfer regardless of the remoteness from the base station.

However, this is not the only strong side of our antennas to strengthen the 4G Yota signal, - their favorable value also worries many, attracting all new and new buyers to the site. Precisely profitable, but not understated; This, let me notice, not the same thing! With cheap, incomprehensible to whom the antennas we do not have, and you do not advise you!

The same antennas for enhancing Yota LTE, which you can see in the catalog of this site, are sold at the best prices in Moscow, which we rightly call profitable! These antennas were not accidental here - they are made of high-quality metal alloys and modern polymers, with the strictest compliance with the requirements of the LTE standard and the global standards associated with it.

Strengthening the modem signalYota technologyMimo.

A separate word deserve antennas that support MultiPle Input Multiple Output technology (MIMO) that have recently appeared in the external device line for Yota. Mimo-antennas are characterized by a more complete use of the bandwidth-provided capacity provided by the LTE standard, which has become possible due to the separation of the receiving-transmitting device into two parts - accepting and transmitting.

The MIMO compliant Internet signal amplifier for Yota is thus not one, but as many as two antennas that need to be installed so that they do not interfere with each other, creating frequency correlations. Such antennas for the LTE modem Yota provide at least twice the best data transfer rate, and this is no change in the level of standards.

To date, the MIMO signal amplifier for the Yota modem acts best solving problems when using Radio Frequency Channels for LTE Standard. Its disadvantage, and then small, it is considered only the need to set two antennas instead of one, but it is successfully eliminated by the use of frequency selectivity technology (by connecting these antennas in one case).

Your choice - antenna and modem (router) in one set

Antenna for 4G modem Yota, like an antenna for another popular Yota-device - Router, you can buy from us not only separately from the modem itself (router), but also with it. After all, the electronic store site sells not only a variety of antennas, but also other devices designed to work in the Wireless network of the Yota operator, as well as accessories for them.

Buying a Yota-modem with an antenna is, without any doubt, the right decision. Antenna, you will have to purchase anyway - not now, so then, having spent annal amount of time on her selection of the modem characteristics, which is not at all as easy as it may seem at first. It is better to do this in advance by buying a modem of the Yota operator with an antenna in a set! So, by the way, not only more convenient, but also cheaper.

Note - Antennas with the built-in Yota modem from us are also sold. Such antennas are predominantly indoor (intended for operation in rooms with normal humidity and temperature); They are optimal for use with laptops and tablet computers, at home, at work, outside the city, on the road - no restrictions!

Sale Antennas for ModemYota and not only

We are engaged not only by selling, but also by installing Yota antennas. This service is one of our most popular: it took advantage of more than 80% of those who have bought these very antennas at one time. Considering how well the specialists of the electronic store site are dealt with Yota's devices, the installation of the antennas does not seem such a challenging task for them.

Here you need to clarify that they are far from always with each other compatible - modem Yota and external antenna. Many modems of this brand, as well as many of its own routers, do not have connectors for connecting such antennas at all, which pushes their owners to experiment with the soldering iron. How can all this turn into? In addition to losing guarantee on the device, nothing ...

With us you can not only purchase modems and routers, but also modify them by adding the possibility of joining the external Yota antennas. Buy alarm amplifier and not to be able to connect it to the modem - this is, of course, unpleasant, but not so much to spoil yourself. Just contact us, and we will eliminate this annoying error of modem manufacturers.

The Yota operator provides its subscribers only wireless Internet. Most of the difficulties of users are connected with this. If a wired technology Allows you to achieve constant high speed and stability (only accidents at stations can be attributed to exceptions), then many factors affect the wireless network.

Let's figure it out if antenna is needed for Yota, and how it can affect the speed and stability of the connection.

External antenna amplifier for modem Yota LTE: need or not?

To understand the question, you need to evaluate the features of the Internet at different times. In the event that the network holds stably, the speed does not fall, then the gain additional devices No need. But in what cases then you should get an amplifier?

Think about buying an amplifier or independent manufacture in the following situations:

constant signal loss in different points at home;
speed \u200b\u200bdrops;
use a large number of devices connected to the Internet through one router / modem.

Users have a choice: to buy corporate equipment, or try to strengthen the signal with your own hands. Let's talk about each method more.

Options for amplifiers

If your task is to provide the Internet a large number of Device, then you will fit the Yota B315 Internet Center with an external antenna. The device itself allows wi-Fi networkAnd the connected external amplifier will increase the stability and reception of the signal.

On the official website you can purchase Yota B315 for 6900 rubles (cost in Moscow and the region). If you do not need an Internet center, then you can do the closer with the external antenna connector - LU150 Lite. Connect the external antenna to the Yota modem only with a special port or USB connector.

Before buying, carefully examine the characteristics of one and second device - the availability of ports must coincide. Connecting the device to the modem is carried out through the pigtail - adapter from the standard antenna socket to the specific connector.
If not sufficiently developed, and the modem is constantly switched to 3G, then when choosing an antenna, this moment also needs to be considered. The device must support both technologies. Otherwise, you will have to buy two antennas.

Strengthening the signal with your own hands

External antennas for the Yota modem, 4G LTE signal amplifiers cost a lot of money. Most users cannot afford to acquire expensive devices. However, it is not necessary to despair in such a situation - you can try to make an antenna for Yota with your own hands.

You can make the amplifier from the remedies. The most common example is a saucepan, aluminum pelvis, foil. The modem is placed inside a pan or a cardboard box, glued foil. Next, the design is attached in the place where the reception of the signal is higher. If you are going to fix the homemade construction on the street, then take care of the protection of the modem from external influences (rain, frost and so on).

Also to enhance the signal appropriate satellite antenna. You must attach a router to the converter, then send the design to the side of a good signal reception. If neither you have no other, then use the copper wire and foil textolite to create antenna Harchenko. More detailed instructions And you can free download from the Internet for it. With the help of our tips you can do without large spending on the amplifiers.