The launch of Windows 7 and nothing happens. Basic solutions when Windows refuses to load

Very often, computer users encounter a problem when the Windows Operations 7 refuses to start. At the same time, many of them do not understand why it can happen. In this case, it would not hurt to know the main and common reasons why such a similar may occur, as well as errors that pop up with this problem and the methods of their elimination.

Error Disk Boot Failure, Insert System disk and. Press Enter.

This is the most common error that appears after the computer is launched. As a rule, the Disk Boot Failure error is displayed instead of starting the operating system. This may indicate that, according to Operation, the disk from which it wanted to run is not systemic. This problem may arise for various reasons, among which are the most common.

It often happens that a disk is inserted into the drive or a USB drive is connected to a PC, the BIOS is configured so that it sets this media to load by default. This leads to the fact that the operator does not start. In this case, you should try to disconnect all third-party drives of the SD memory type, flash drives, smartphones, etc. It is also necessary to remove the drive from the drive, and then try again to start the computer.
Perhaps this time the operation will start.

In addition, the problem may occur when setting incorrect downloads to the BIOS. In this case, the instructions from the method above will not be able to help. Even in the case when the computer started to run normally in the morning, and in the evening it stopped, it is necessary to check this option because bIOS settings Can be lost. This may affect the nursing battery on motherboard or interruptions in the power grid, as well as static discharges. Checking the settings, you need to check that hDD The BIOS is determined.

In addition, if the operator sees the hard drive, you can resort to the help of the system for restoring the system startup. This will be indicated slightly lower. In the case where the system cannot determine the hard disk, if you can, you can try to disconnect the hard drive and re-connect it. At the same time, attention should be paid to the connection hard disk with motherboard.

In addition, such an error may occur for other reasons, among which you can note the problems with the Winchesser itself, the presence of viruses in the system and much more. Whatever it was, it is recommended to check all the ways that were described above. If nothing helps, then there is another solution for solving the problem that fit almost for all cases when "seven" does not want to run.

Boot Bootmgrr is Missing

This error may also appear when the seventh version Operation refuses to start. At the same time, the message bootmgr is missing on the black screen appears. Such an error may appear for various reasons, among which you can mark the activities of viruses, incorrect actions of the user itself, which led to a change in the boot record of the hard drive or some mechanical problems in the hard disk. Options for solving this problem can be searched on the Internet.

NTLDR IS Missing Error. Press Ctrl + Alt + Del to Restart

This error manifests itself almost as described above. At the same time, it is a few different ways to eliminate the previous one. To eliminate this problem, you can use special instructions that are easy to find on the Internet.
Windows 7 is loaded, but displays only a black screen and mouse cursor

If, running a computer, the screen does not display the operating table and no "Start" menu, but only a black screen with a mouse cursor, then it is easy enough to solve this problem. Very often, such a problem occurs after removing the virus using anti-virus utilities or independently. As a rule, not all changes that caused damage was corrected, which led to the appearance of a black screen. This error is fixed quite simply, what can be found in various forums relating to this problem.

Troubleshoot Windows 7 launch errors using integrated utilities

In some cases, when the system refuses to start due to changes in the hardware configuration, incorrect disabling PC or any other errors, when the PC starts, the system recovery screen will appear, with which you can try to resume the launch of the OS.

However, if such a screen does not appear, then you can click on F8 after the BIOS booted, but the operator has not yet started loading. As a result, a menu will appear on the screen with the PC Troubleshooting item, which must be pressed.

After that, the notification will jump in which it will be reported that the operation of the operating files began. Then a proposal will appear to set the language where you want to specify Russian. Next you need to go under your account. To do this, it is better to apply an administrator account. If the password is not installed, then it can be left blank.

After these manipulations, the Operation Recovery window will open in which you can activate automatic search and troubleshooting problems that do not normally start the system. To do this, click on a special link.

After identifying all the problems, the application in automatic mode will eliminate all the errors found that prevented the Windows startup. It happens that the utility does not find any problems.

In this case, you can resort to the help of the OS recovery function. If the problem with the start of the transaction appeared after updating the drivers or something else, this action can help. In principle, it is clear how this procedure can quickly eliminate the problem associated with updating the components of the Operations.

In general, it is almost all the main problems that may arise when the system fails to start. If nothing from the above helped, then you should contact a specialized computers repair company.

Why not run Windows 7? Loading the operating system can be completed by a multiple reasons: due to the hardware failure, due to the incorrectly installed software, due to viruses, but most often due to problems in the Windows itself. To make a description of the process of searching for the source of the failure of the failure, first we will analyze the seven launch sequence.

Windows 7 download steps

The launch of Windows 7 is conditionally divided into three stages that are divided into phases.

1) OSLoader.

OSLoader. - The first stage of Windows 7 download, which starts immediately after the BOIS code is executed. At the beginning of this stage, a small group of the main drivers required for further reading data from the hard disk is loaded. Further winLoad.exe., Windows 7 bootloader, proceeds to initialization and start loading the kernel, loads into rAM Registry bush System. and the next batch of drivers with the startup parameter Boot_STart..

Stage OSLoader. lasts 2-3 seconds. By the time of appearance, the system logo appears on the screen, it is already completed.

2) MainPathBoot

MainPathBoot. - The main and longest stage of Windows loading. Consists of several phases. Visually, this stage continues from the appearance of the system logo on the screen and ends with the beginning of the desktop boot. The duration of this stage can be different - on average, from a dozen seconds to a pair of three minutes.

• Phase Presmss.

During this phase is fully initialized windows kernel 7, the Plug and Play equipment dispatcher is initialized earlier. running drivers Boot_STart. and hardware drivers.

Errors arising during this phase are often associated with the problems of the main computer devices or their drivers.

• Phase SMSinit.

The phase begins from the moment the session dispatcher control is transferred - SMS.EXE.. At this time, the remaining registry bushes are initialized, drivers are loaded with the launch parameter "Auto". At the end of the phase, the control goes to the file WinLogon.exe. - User entry program in Windows. Visually about graduation Smssinit. Specifies the appearance on the input invitations screen.

Failures and decelerations during this phase are often associated with the delay in the download of the video driver or the problems of the video subsystem.

• Phase winlogoninit.

This phase begins with the start WinLogon.exe. (Welcome screen) and ends with the boot of the desktop - the start of the Windows - File shell Explorer.exe.. During her stroke, the system reads and executes scenarios group Policy and launches services (system and third-party). The phase can last long and accompanied by high processor loading.

Failures at this stage are often caused by services. third-party applications, including antivirus.

• Phase Explorerinit.

Starts the start of the shell and ends with the launch of the desktop window manager process. During the course of this phase, the desktop icons appear on the screen. At the same time, there is a further launch of the services, the start of auto-loaded applications, data caching, etc. All this is accompanied by high load on hardware resources - hard disk, memory, processor.

Problems and delays during Explorerinit. Often are associated with an insufficient power or malfunction of the equipment.

3) PostBoot

Stage PostBoot. It begins the appearance of the desktop and ends after loading all that is written in autorun. During this period, the main part of the applications started with Windows begins to work. After graduating from stage, the system goes into inaction.

Delay and failures at the stage PostBoot. Associated with automotive programs, sometimes - with viral activity.

Failures at various stages of system loading

As it was already briefly mentioned, malfunctions at different stages of launching Windows 7 are manifested in different ways: some are associated with equipment, others - with drivers, third - with system registry or other files are critical for download. Understanding which processes occur at each stage of the start system, you can determine the range of possible problems.

Briefly about hardware problems

You will not stop in detail on the equipment in detail, since our topic concerns Windows 7, but sometimes it is possible to determine whether the physical device or system is broken, it is very difficult.

• A repeated failure of the same driver at the Windows start stage may be associated with a device malfunction controlled by this driver.
• A series of diverse errors ( blue screens Death), which arise at different stages of loading, is often due to problems of RAM.
• Lack of image or artifacts on the screen, while the sounds of the loaded system are heard, may indicate the problems of the video card.
• If Windows load does not even start or suddenly stops - "freezes" in one place - it is possible that it fails the hard disk.
• Suddenly shutdowns from the computer during Windows boot say "in favor of" power supply problems or motherboardand sometimes something else.

Damage to boot files

In the early stages of Windows startup, damage or lack of critical files can manifest themselves display on the phrase screen "Bootmgr Is Missing" or other error messages. But it happens that no messages are displayed, and the user simply observes the black screen with the cursor in the form of an arrow or without it.

The bootloader of Windows 7 and 8 operating systems, like other boot items, is not available to the user - it is in a separate hidden section And it can not be deleted by chance. However, the user by ignorance can format this section by booting from an external medium. Then Windows will not be loaded.

In the screenshot is shown boot section Hard disk, access to which is obtained from the recovery environment.

Another part of the important files is on the system disk in the catalog and subdirectories C: Windows. There is also a system registry.

Damage registry

In case of unavailability or damage to the registry, the Windows load may not even start.

The system itself will inform you about failure and automatically starts the built-in recovery wizard. He often helps to identify and eliminate the problem - the registry will recover from backup.

But the self-setting of Windows 7 boot may not always. So, it does not happen if the recovery wizard cannot find backup copies of missing or damaged data. In these cases, the system needs help user.

Windows 7 startup recovery

Recovery environment

Restore the download of Windows 7 much more convenient than Windows XP, because the seven is equipped with a set of tools Windows Recovery Tools (WRT)which is available from the recovery environment. Recovery Wednesday When installing Windows is installed on a hard disk, in a separate section, and has its own bootloader. Therefore, it retains performance regardless of what is happening with the system.

To get on the recovery environment, select from the menu F8. (Additional Windows 7 launch options menu) "Troubleshooting Computer".

For admission to the recovery parameters, the system will ask you to conduct a password. If you do not have administrator rights or forgotten the password, Windows 7 recovery environment will have to run from the installation disk.

After the window opens "System Recovery Settings" - Select the first option from the list: "Run Restore". After self-diagnosis damaged boot files, Registry or individual startup parameters will be restored.

This tool helps solve the problem in most cases, and it should be resorted to it when you do not know exactly why not Windows is not started.

Two ways to restore the system

If the failure occurred after installing the program, due to the virus infection or due to changes in the registry, return the seven ability to boot help "System Restore". But it will be sense from it only when control points of recovery are preserved on the hard disk.

This tool is familiar to many: you choose a suitable checkpoint when the system function normally, and roll back. All changes made later selected dates will disappear, and you can download Windows normally.

If there are no points, but you have saved a backup copy of the external drive, will help the tool "Restoring the image image". Connect the media to the computer with archived and follow the instructions for the recovery wizard.

Manual recovery registry

If the above manipulations did not help and Windows is unclear why, but it does not start, you can try to restore the registry from the backup. Copy windows registry 7 automatically generates every 10 days and saved in the directory C: WindowsSystem32Configregback. To restore the system performance, you need to copy all 5 files from the above folder to the folder C: WindowsSystem32Configwhere there are current registry files. Old files are better not to delete, but rename (in extreme case).

• From the list of parameters, select the command prompt. Open it and start the Notepad command - it will be needed to start Windows Explorer.

• In the Notepad window, go to the menu "File" and choose from it item "Open"

• Go to the directory C: WindowsSystem32Config. To see everything in this folder, change the type of files with. tXT. on the "all files".
• Files Default., Sam, Security, System. and Software. (without expansion) - this is the current registry. Rename them into anything - add them at least the expansion .old.

• Open the folder REGBACK With backups of registry files and one by one, copy them to the folder config.

• After you copy everything, restart the computer. If the Windows load failure occurred due to the registry fault - the problem will be solved.

The reboot button is at the bottom of the window. "Recovery Settings".

Restoring files

Own means of restoration of protected windows files - Utility sFC.exe.may be successfully launched in the recovery environment. Usually it is launched with a parameter / Scannow - for automatic search and corrected problems found. In the recovery environment, you will also have to specify additional parameters: location of the autonomous boot directory and stand-alone directory of Windows (for the Windows folder recovery environment, where it is located, are autonomate catalogs) are parameters / offBootdir. and / offwindir..

Completely the command is written as shown in the picture:

IN offBootdir. You need to specify the path to the system disk, and in offwindir. - The path to the Windows folder. Just do not forget that in the recovery environment, the letters of partitions may not coincide with those that you see in the explorer during normal Windows loading. "Right" letters can be viewed by opening the conductor using a notepad.

If, after this, Windows 7 still does not start, you may have to manually restore the boot files, as well as overwrite the main boot record (MBR) of the hard disk and the boot code of the system partition. This will also help you own funds Windows.

To re-create the boot files, open the command prompt and run the following command: BCDBoot.exe C: Windows.Do not confuse the letter section.

To overwrite the MBR and VBR (boot code of the partition), perform the following commands: bootrec / fixmbr and bootRec / FixBoot.

After that, check the download.

windows 7 has become a classic for home use, It is it that it is installed on each second computer, despite the development of new operating systems from Microsoft. Going out to the market in 2009, "Seven" still will not get rid of problems during the launch, which are pretty spoil the nerves of a multi-year user audience. To simplify the user's life, the computer is running "seven", and this article is written. In it, consider how to perform windows restoration 7, if it does not start.

Bootmgr Is Missing.

The most common problem that appears during the launch of the "seven".

The reasons for its appearance can be:

• damaged hard sectors disk or non-working SSD memory cells on which Windows 7 is installed (in most cases you can perform their recovery);
• spontaneous power off or restart PC via the RESET key;
• virus activities (very rarely);
• inretful access of the user with utilities for breaking the hard disk.

Make a mistake to disappear in several ways. We will look at how to restore the computer with the means of the OS itself.

• If there are problems during the launch of Windows 7, press F8 to call the menu with the list of additional computer start settings.
• Select the option "Troubleshooting ...".

• Choose Russian and press "Next".
• Choose account with administrator rights.
• Click on "Run Repair" to operating system I tried to find and correct the problem alone.

• If the error is not fixed, run the command line from the OS renewal parameters window.
• Sequentially enter the command:

"Bootrec.exe / fixmbr" - Record MBR in system section;

"Bootrec.exe / fixboot" - creating a boot record on the system volume.

• Reboot and run a computer.

Look more: Setting up OpenVPN Windows 7

If, after executing the PC actions described above, it still does not detect the installed Windows 7 during startup, run the BootRec.exe command via the command line with the "RebuildBCD" attribute.

It scans all the information installed on the computer for long-term storage of information for the presence of the installed OS compatible with the "seven" on them, and will allow you to add them to the download list.

And in the most recent case, when nothing helps to make the restoration of the launch of the "seven", reserve old folder BCD, which is responsible for launching a PC, and create a new one. This is done using the chain of the commands below:

Problem "Disk Boot Failure" or message with the text "INSERT SYSTEM DISK"

The start-up error is caused by one of several reasons, the essence of which is the following: The computer tries to find the boot record on the disk that is not bootable. Factors that do not allow Windows 7 will start:

• The device from which the computer begins to load is not a system disk - try turning off all flash drives, telephone, camera, including external hard drives, and restart the system.
• Check the BIOS settings responsible for the priority of the download devices - there is a high probability that the computer starts to load from the disk that is not systemic. Also look at the BIOS or through one of special utilitiesThe Winchester is found on which Windows 7 is installed.
• Reconnect the HDD to another loop and power cable, it is possible a problem lies in the unreliability of the connection or damage to one of the cables, for example, due to its intentional inflection.

The list of reasons can be safely ranked installed windows 7 Due to the fact that the disk with it was formatted due to the inattention or inexperience of the novice user, and it will help her re-installation or restore the remote partition.

If none of the options brought the desired result, try to restore the OS, as described in the previous paragraph, and also make sure the hard drive is working.

Look more: Installing Virtual Windows XP.

Impossibility to run Windows due to damage to the registry files

Among other things, Windows 7 may not boot due to damaged registry files.

As a result, the computer will inform the user about the problem and will launch an application that allows you to restore the operating system.

But the tool for automatic recovery of Windows 7 is far from always efficient and, for example, in the absence of a backup copy of the damaged data, the user will have to manually perform the operating system recovery.

• Call a window with an extended list of Windows startup parameters using F8.
• Select "Troubleshooting ...".
• Next click on the link: "System Restore".

• In the first window, click "Next".

• Choose one of the created points and click "Next".

• Confirm the execution of a given operation by clicking on the "Finish" button and wait until the OS is being restored.

After a few minutes, Windows 7 is completed, the computer will reboot, and most likely, it will start normally.

(Visited 49 777 Times, 156 Visits Today)

windowsProfi.ru.

Why does not run Windows 7 and how to restore the launch

If the user has a problem when Windows 7 does not start in the computer or laptop, then this article will help solve this difficult task. The launch of Windows 7 is sometimes impossible due to errors in the system after hardware problems, incorrectly installed software, malicious utilities, etc.

But the most common reason why Windows 7 does not load, lies in the operating system itself.

Solution to the problem

In the case when all the initial stages of launching Windows 7 in a PC or in a laptop are performed normally, and still does not start Windows 7, then usually beginner users it puts in a dead end. Although if presence detailed instructions, Question: "What to do?" Even newbies will not appear. If the problem is a hardware failure, then it will indicate a laptop speaker signal or stationary computer With post test. If so, then start the OR will fail.

But if a software problem and the process stops at the Windows loading phase 7, then the user has encountered the most common problem solved using the typical action algorithm.

Instructions for action

You must use the OS recovery tool. During the PC launch process, if Windows 7 does not start, the system often recommends the owner of the computer or laptop to select download options. If for some reason this offer has not been received, the user can independently open this menu click on the "F8" button. Then proceed to restore the normal loading "seven".

What if the above instruction did not cope with the problem?

To eliminate the problem when Windows 7 does not start, you must apply the CD from OS:

1. Install the installation disk in the PC drive;
2. Run the system from the disk (in the bio d b. The corresponding order of loading system from media is installed);
3. In the displayed window, click on "Apply restoring functions that eliminate problems with the loading of OS" and click on "Next";
4. Then in the OS Recovery Settings menu, click on the "Start Restore";
5. Wait until the time analysis of the system and eliminate the causes of failures;
6. Perform a reboot of a PC;
7. In the BIOS, set the system launch from the hard disk (when leaving the BIOS, you must save the adjusted adjustments);
8. Reboot the computer again;
9. Ready! Now Windows 7 will boot normally.

Using the command line

If for some reason I could not restore Windows using the setting disk, then there is another way to do through the command line.

First you need to do the steps specified in the paragraph about the restoration of the normal download "Seven". Changes are only that simply in the "System Recovery Settings" menu, you must now specify the "Command Line" section.

What to do when it was not possible to achieve a positive result by executing the above instructions?

If you could not succeed and the user has already reached this part of the article, it means that the problem cannot be attributed to the category of typical failures boot distribution OS. It will take all further actions to make windows safe mode. It is recommended to analyze the disk "C" for the appearance of broken clusters.

For the entrance " safe mode»You must do the following:

Why are preventive measures important?

The Windows 7 provides a special system that can make special reference points, with which, if necessary, restores. Applying this feature of protection, even the user is always happy to return the OS to a working condition.

For example, in case of failures due to the incorrect installation of applications, drivers and other utilities like codecs or when errors occur due to making adjustments to the registry.

It should be noted that in the "seven" it is possible to drive a fixed amount of memory on the hard drive specifically for such protection of the OS. In Windows 7 available exercise self-configuration Protection Along with system data also files or you can do it separately.

windowstune.ru.

Does not start Windows 7 launch recovery does not help

Often, when working on a computer, such a deficiency arises as, Windows 7 does not start, the start-up recovery does not help. In previous versions, the OS did not exist recovery, and therefore the choice windows systems 7 gives the opportunity to do everything as it was without loss. In order to restore the system, we need to decide how to do it. There are several categories. Namely:

Using the load of the last successful entry.

For the rapid elimination of the system, you must start the PC and clamp the F8 key. After selecting the "Last Successful Configuration" item and press ENTER. This method allows you to download the computer, and restore all the data from the registry, as well as the driver files that contribute to the successful download of your OS.

Recovery system in normal order.

If the download does not help, then you need to refer to the restoration of the system, and for this you need to have existing recovery points. They allow you to roll back the computer settings until all the device functioned. The system recovery is in the Start menu, in subparagraph control panel. To do this, select the appropriate date, and follow the instructions in the future. With a good recovery, after a reboot, a window will be released about it.

"System Restore" using the Windows main disk.

If everything still does not start Windows 7, the start-up recovery does not help, then you should refer to secure loading. The menu that is still started with the F8 clamped. In the list of proposed options, the "Troubleshooting of the computer" is selected. After you need to insert the original disk with the operating system corresponding to the installed, and select the "Restore System" field. Next will be released with several recovery options. Considering that the "Startup Recovery" did not help us, then you should select "System Restoring", and further, as in the previous paragraph, we select available recovery points.

Resorting to the backup system, which was created earlier.

In order to use the recovery from the backup, you should connect a USB device with this file. And go to the start, where to choose the control panel and after restoring. If the system does not start, and there is no possibility to do this manipulation, then the previous paragraph should be passed. In a new window, select "Extended Methods ...", further "use the image image created earlier." After that, you will be offered to use the profile archiving. Think here yourself, you need it. After you need to restart the computer, and go through all the instructions for setting it.

Output

If not one of the methods did not help and still does not start Windows 7, the start-up recovery does not help, then you should reinstall the operating system, and it will have to lose all of its data.

pro-Tablet.ru.

Windows 7 does not start. How to restore the launch?

What is the reason for failure windows startup 7 on the computer? The following factors may affect the ability to issue an error when you start Windows: computer infection with viruses, failed equipment configuration, errors when installing software, imperfection of the operating system.

It is required to find the true cause of their issuing, for this it is necessary first of all to figure out which stages is the loading of Windows 7. It consists of 3 main stages that are in turn divided into steps:

Windows 7 download stages

First Stage - Osloader

Immediately after the execution of the BIOS code, the first download stage begins. Here at the first stage there is a connection of the main drivers, which are required to read the data from the hard drive. After that, "WinLoad.exe" proceeds to load the kernel, loads in the RAM of the System registry bus, as well as the BOOT_START program.

The duration of the first stage is no more than three seconds. It ends when the Windows 7 emblem is displayed on the monitor.

Second stage - MainPathBoot

MainPathBoot - Home and Long-time Stage. Duration sometimes reaches a few minutes. The stage begins with the display on the Windows 7 emblem monitor and ends when starting the desktop start.

PRESMSS Stage

The kernel of the operating system is determined, "Plug and Play" is loaded, the "Boot_start" and computer component drivers are defined. If errors appear, this indicates a problem with computer components.

Stage SMSSinit.

Next proceeds to "smss.exe". The remaining registry bushes are determined, the operation of the program of the type "Auto" is included. At the final stage, the management of "WinLogon.exe" is the management utility to the operating system. "SMSSINIT" is completed when the menu is displayed on the monitor with the user name and password.

Here errors speak about the failures of the video card or its drivers.

Stage winlogoninit.

The beginning is carried out from the launch of "WinLogon.exe" and is completed with the appearance of the desktop download "explorer.exe". Includes the implementation of group policy scenarios and service download. This is the most time-consuming stage for the processor and usually takes a lot of time.

Here errors indicate problems with the services of non-Windows programs, for example, antivirus.

Stage Explorerinit.

It continues from the shell loading and ends with the download of the windows dispatcher. During the stage, shortcuts begin to display, parallel the programs are loaded in autoload. This stage is characterized by the largest load on the processor, Winchester and RAM.

Here errors indicate defects of components or the need for their upgrade.

Third Stage - PostBoot

It lasts from the time of displaying the desktop and ends with full opening of programs from autoload.

Errors indicate the problems of applications that are found in the autoload list or the presence of infected files in the computer.

Errors arising from startup stages

Examined which errors occur at various stages of the system startup, it is possible to identify specific problems.

Errors due to the defects of computer component:

1. Repeated errors of some driver indicate a defect of equipment related to this program;
2. Multiple malfunctions at various stages indicate a RAM defect;
3. If there is no image on the computer monitor, but there are windows sounds, this indicates the incorrect work of the video device;
4. If it is impossible to start launch windows either its interruption, it is necessary to check the condition of the hard drive;
5. If occurs full shutdown When starting, the power supply unit or motherboard may be released.

No boot file fault

The flashing on the BootMGR IS Missing monitor indicates the absence or fault of the boot files, and sometimes it happens just an empty black screen.

In the absence of a bootmgr loader in the computer, the system does not boot. This section sometimes accidentally erases the user himself, using boot disk.

Also required files To start the system, are located on a C drive: in the Windows folder.

Registry problems

Window sometimes can restore it using the recovery wizard.

Restore operating system startup

Recovery environment

Windows 7 has "Windows Recovery Tools WRT". To restore, you need to select from the F8 menu "Troubleshooting Computer".

Next, the "System Recovery Settings" menu appears - you need to select "Start Restore".

This will restore parameters and startup files.

Recovery methods

When software type Errors, the operating system will help the "system restoration".

Manual recovery

In case of absence positive result After using the system, it is possible to manually restore the registry from the backup, which is on C: in the WindowsSystem32Configregback directory. You need to copy files from it to the WindowsSystem32Config directory.

Restoring files

Exists useful program "Sfc.exe", which can be launched in the recovery environment. You must specify the following: Parameters and location of the download folder and autonomous directory of the Windows directory). Parameters / OffBootdir and / offwindir.

In the event that the launch problems are not eliminated, you must manually restore the boot files.

windowstune.ru.

Windows 7 launch recovery. How to disable Windows 7 launch recovery

Quite often in computers use Windows 7 startup recovery after the errors encountered. It can both well and not very positively affect your operating system. Today we will talk about how to manage the restoration of the system launch.

What is a means of restoration

Windows 7 start recovery tool restores OS. It can correct a number of problems that interfere with the right windows work. Wherein this process starts scanning a computer, thereby determines the presence of problems and errors, trying to eliminate them and ensure the correct and effective work Your "Iron Friend". By default, in each Windows operating system, the Automatic System Recovery option is enabled. If you wish, it can be turned off. But without special knowledge own computer Do not need to do similar manipulations - let the car be checked, restored and operates in normal way. Although there are such moments when the restoration of Windows 7 launch is long and bored. This is already a signal to think about checking the "iron". Of course, Windows 7 launch recovery does not give 100% warranty proper work Systems - there are such errors with which the recovery means cannot cope. We will talk about them further.

What do not cope with the means of recovery

The Windows 7 start recovery tool cannot solve some problems. As a rule, system files that were damaged, deleted or not delivered at all are restored. For greater recovery is not capable. So, it cannot eliminate the failure of the equipment - for example, a hard disk or memory incompatibility. In addition, Windows 7 launch recovery cannot protect the computer from viruses.

Recovery will not help with the problems of installing the system. So, if the operating system initially got up "crooked", then there will be no sense from the means of recovery. Personal files (Photo / Video / Documents) are not refundable. In order to save your data, you need to archive.

If recovery does not help

In order to solve problems that are not eliminated by restoring the system, it is necessary to detect the problem. On the screen you will have a summary error information and some documentation. Thus, it will be possible to understand what is the matter, and take appropriate measures. As a rule, if recovery does not help, then you need to "correct iron" or reinstall Windows.

Manual loader recovery

There are several ways: restoration windows bootloader 7 manually, using programs, automatically and with system rollback. Now we will talk about how to restore the system about how "hands".

In order to answer the question: "Windows 7 boot recovery - what to do for manual recovery? ", I need to be patient and, of course, the Windows 7 boot disk. Now let's start directly to the recovery process.

1. Set up bIOS Parameters So that your drive stood on the first place and reading place.
2. Insert the installation disk from Windows 7 into your computer and restart the device.
3. You will see a familiar window reinstalling the system. At the bottom of the left you will see the "system restoration". Click on this button.
4. After that, you will pop up the "System Recovery Settings" window. Select the one you want to restore, click "Next".
5. Next, select "Restore System Start" - "Command Line".
6. Write in the window that opens: "bootrec.exe".

BOOTRECE keys

For manual method Recovery After the last item is fulfilled, you will see a window with so-called keys. They explain how the Windows 7 system will be restored. Now we will see which keys are responsible for what.

FixMBr - records the main boot record to the system partition compatible with Windows 7. This option is used when the main maintenance is damaged. boot records Or it is necessary to delete non-standard codes. Existing table sections are not overwritten. Restoring Windows 7 launch can not bother you because of these records, but with FixMBr you get rid of the problem once and forever.

FixBoot - A new boot sector compatible with your operating system is written to the system partition. Used this key With:

Replace the boot sector with non-standard options;

Damage to the boot sector;

If it was launched previous version Windows.

After you choose the necessary tool for restoring Windows 7, write it and press ENTER. Wait for the process to complete. Ready - Windows 7 bootloader works again and restores the system. This will load, restore the system startup will be in good condition.

Recovery programs

In order to "return" the start of the system, you can use various Windows programs, the Windows 7 launch restore will be implemented almost automatically. This method is perfectly suitable when there is no original windows disk. What programs do you have to restore?

HEREN'S BOOT CD

As a rule, by salvation in the absence of the original Windows 7 disk will be the so-called LiveCD, which can be written anywhere: even on the disk, even on the USB flash drive. There are many such programs. The simplest I. convenient way - It is to use Hiren's Boot CD. There are a lot of all kinds of Windows restoration utilities on this disk, but today it will be about the most convenient and most common. Before you start work, you need to record LiveCD, after which it is loaded through the BIOS. When it is implemented, it will be possible to move to the following steps.

Option 1 - Paragon HD Manager

One of the most popular system recovery utilities is Paragon Hard Disk Manager. In order to restore the Windows 7 system through it, it is necessary:

Option 2 - MBRFIX

Another convenient, fast and popular system recovery utility - MBRFIX. It differs little from the previous one. Is that your desire. In order to ensure the restoration of the Windows 7 system, you can't wait long. Enough to perform the following steps:

1. Select when startup LiveCD "Mini Windows XP".
2. In the menu that opens, find and select "Partition / Boot / MBR" - "COMMANDLINE" - "MBRFIX".
3. To restore the bootloader, enter the following entry: MBRFix.exe / Drive 0 FixMBr / Win7 / YES.
4. Wait for the process to complete and restart the computer.

Recovery with command line. This is another good and qualitative way to restore the system. In order to use the command line as a Windows 7 recovery tool, you need:

1. Run secure mode on your computer. Do not forget to select a command line support option.
2. Sign in.
3. Register in command line rstrui.exe.
4. Press ENTER and wait for the completion of the processes.

Disable recovery

You can disable the system start recovery using Windows 7. To disable the vendor restoration of Windows 7 when the computer is started, you need:

1. Go to "Start" - "Control Panel" - "System" - "System Protection".
2. Find the Properties window and open the System Protection tab.
3. In the "Protection Parameters", find and select the disk on which you want to disable the system recovery, click "Set up".
4. In the "Protection of the system for ..." in "Parameters", check the box to "Disable System Protection".
5. Press approx. Such simple I. fast methods You can conduct various manipulations with the restoration of the system. Do not forget that Windows 7 recovery can be done using a system rollback. In this case, your personal data will not be damaged. System rollback is possible only if it can start, that is, if the Windows 7 boot recovery is turned on, which all the time checks the presence of errors, but the operating system is working normally. It will be necessary to "roll back" the OS on the date when there was no problem. Windows is restored using a standard set included in the package. But if your computer has been pronounced in some unpleasant errors, then in the process there may be some problems that will not particularly affect the quality of the system work - you will simply be unusual and inconvenient to work at the computer. The most frequent problem is the disappearance language panel in system.

Language panel and restoration

Language panel is what can be seen and familiar to everyone. As a rule, there is a panel on the toolbar that shows the keyboard layout and allows you to switch it. Sometimes it happens so that it disappears. Then there is a need to restore the launch and work of the language panel in Windows 7. The easiest way is to refer to the built-in recovery tools. Why do you and for what reasons "covered" the language panel "covered" - to judge quite difficult, since there may be a huge amount of them. Nevertheless, everything is easy and simply correct. We will proceed to eliminate the problem with this panel. Methods here are two.

Method 1 - "People's"

1. Press Win + R and run intl.cpl. You can also take advantage of: "Start" - "Control Panel" - "Language and Regional Standards".
2. Go to "Languages \u200b\u200band Keyboards".
3. Open the "Change Keypad" menu.
4. Next, you must select the language panel in the "Languages \u200b\u200band Text Input Services" window.
5. Check the "secured in the taskbar" and "display test tags in the language panel."
6. Next, you need to take changes and click on approx.

Now the language panel must appear.

Method 2 - "Advanced"

1. Press Win + R and enter the REGEDIT.
2. Find a tab in the registry:

HKEY_LOCAL_MACHINE \\ SOFTWARE \\ Microsoft \\ Windows \\ Currentversion \\ Run

3. Check CTFMON for the relevant "program". If it is not, create it.

4. Right-key, click Run and "Create a String Parameter".

5. Assign the name CTFMON and by pressing the PCM to it, click on "Edit".

6. Push: "C: \\ Windows \\ System32 \\ Ctfmon.exe".

7. Click OK.

The language panel will put on its place, the designated Windows 7. What method of returning the panel to the place is suitable for you - decide for yourself. It all depends only on your skills and desires. But do not forget that the computer can be "wrapped" to such an extent that in the end it will stop working at all. Careful S. system files. Well, if you have several computers - you can always see how to fix one or another error occurring in the system.

In extreme cases, only the complete reinstalling system without data saving is saved.

It is carried out using Windows installation disks. Before you completely "demolish" the system, make sure that all methods of recovery do not work. If there is no exit, insert the disk into the drive, configure the BIOS to boot from the disk and proceed to work. Very often, when loader fails, problems may arise with the installation of a new windows version or with waiting time. Try to carefully read everything that the installer writes. Take care - any computer requires due, often very painstaking care.

Such simple methods You can put in order your system. Restoring the Windows 7 launch system and the language panel is not so difficult. If you doubt whether you can independently do it yourself, call the wizard. He will definitely tell you the faithful and high-quality way to correct the errors. Try to spend all the necessary manipulations to protect and check the computer on time and regularly. Good repair!